Error: Doorbell On Sunultra 20 Under Sles8 - Suse

This is a discussion on Error: Doorbell On Sunultra 20 Under Sles8 - Suse ; Hallo, may I have some ideas concerning the ERROR messages during the boot process of our SunUltra 20 under SLES8 SP3 with an attached Hitachi SATA drive: .... .... RAMDISK: Compressed image found at block 0 Freeing initrd memory: 1245k ...

+ Reply to Thread
Results 1 to 2 of 2

Thread: Error: Doorbell On Sunultra 20 Under Sles8

  1. Error: Doorbell On Sunultra 20 Under Sles8

    Hallo,
    may I have some ideas concerning the ERROR messages during the
    boot process of our SunUltra 20 under SLES8 SP3 with an attached
    Hitachi
    SATA drive:
    ....
    ....
    RAMDISK: Compressed image found at block 0
    Freeing initrd memory: 1245k freed
    VFS: Mounted root (ext2 filesystem).
    SCSI subsystem driver Revision: 1.00
    kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
    libata version 0.71 loaded.
    sata_nv version 0.05
    PCI: Setting latency timer of device 00:07.0 to 64
    PCI: Setting latency timer of device 00:08.0 to 64
    ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD400 irq 21
    ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD408 irq 21
    ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01
    87:4763 88:407f
    ata1: dev 0 ATA, max UDMA/133, 488390625 sectors (lba48)
    ata1: dev 0 configured for UDMA/133
    ATA: abnormal status 0x7F on port 0x977
    ata2: thread exiting
    ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC000 irq 20
    ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC008 irq 20
    ATA: abnormal status 0x7F on port 0x9E7
    ata3: thread exiting
    ATA: abnormal status 0x7F on port 0x967
    ata4: thread exiting
    scsi0 : sata_nv
    scsi1 : sata_nv
    scsi2 : sata_nv
    scsi3 : sata_nv
    Vendor: ATA Model: HITACHI HDS7225S Rev: 0.71
    Type: Direct-Access ANSI SCSI revision: 05
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    SCSI device sda: 488390625 512-byte hdwr sectors (250056 MB)
    Partition check:
    sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 >
    Fusion MPT base driver 2.05.05+
    Copyright © 1999-2002 LSI Logic Corporation
    mptbase: Initiating ioc0 bringup
    mptbase: ioc0: ERROR - Doorbell ACK timeout(4)!
    <===============================
    mptbase: ioc0: ERROR - Doorbell ACK timeout(4)!
    <===============================
    ioc0: 53C1030: Capabilities={Initiator}
    mptbase: Initiating ioc1 bringup
    ioc1: 53C1030: Capabilities={Initiator}
    mptbase: 2 MPT adapters found, 2 installed.
    Fusion MPT SCSI Host driver 2.05.05+
    scsi4 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=222, IRQ=19
    scsi5 : ioc1: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=222, IRQ=16
    blk: queue f01e7418, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
    hda: attached ide-cdrom driver.
    hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
    ....
    ....
    Nevertheless the system is running without any problems but it would
    be
    nice to know the meaning of these errors.

    THX, Rainer B.


  2. Re: Error: Doorbell On Sunultra 20 Under Sles8

    RBläs wrote:

    > Hallo,
    > may I have some ideas concerning the ERROR messages during the
    > boot process of our SunUltra 20 under SLES8 SP3 with an attached
    > Hitachi
    > SATA drive:
    > ...
    > ...

    --------------------snip-----------------------------
    > Copyright © 1999-2002 LSI Logic Corporation
    > mptbase: Initiating ioc0 bringup
    > mptbase: ioc0: ERROR - Doorbell ACK timeout(4)!
    > <===============================
    > mptbase: ioc0: ERROR - Doorbell ACK timeout(4)!
    > <===============================
    > ioc0: 53C1030: Capabilities={Initiator}
    > mptbase: Initiating ioc1 bringup
    > ioc1: 53C1030: Capabilities={Initiator}
    > mptbase: 2 MPT adapters found, 2 installed.
    > Fusion MPT SCSI Host driver 2.05.05+
    > scsi4 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=222, IRQ=19
    > scsi5 : ioc1: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=222, IRQ=16
    > blk: queue f01e7418, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
    > hda: attached ide-cdrom driver.
    > hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
    > ...
    > ...
    > Nevertheless the system is running without any problems but it would
    > be
    > nice to know the meaning of these errors.
    >
    > THX, Rainer B.



    A kernel bug. Since your system works it's probably o.k. but you may want
    to consider updating your system or your kernel.

    Here's an article:

    http://lists.us.dell.com/pipermail/l...ry/012405.html


+ Reply to Thread