Network Problem configuration on SUSE 10.2 - Suse

This is a discussion on Network Problem configuration on SUSE 10.2 - Suse ; Problem of network configuration Help me please, I have installed the OpenSuSe 10.2, all seem right but I'm not able to connected to any devices in my network space and I'm not able too to going out to internet. I ...

+ Reply to Thread
Results 1 to 3 of 3

Thread: Network Problem configuration on SUSE 10.2

  1. Network Problem configuration on SUSE 10.2

    Problem of network configuration

    Help me please,

    I have installed the OpenSuSe 10.2, all seem right but I'm not able to
    connected to any devices in my network space and I'm not able too to
    going out to internet.

    I have follow the same procedure of configuration for SUSE 9.3, where
    all worked fine without any problems.

    After I have finished to install the new Open SUSE 10.2 I'm not able
    to connect to the web space.

    I give some details about my configuration:


    # ifconfig
    eth0 Link encap:Ethernet HWaddr 00:08:A1:05:868
    inet addr:192.168.0.14 Bcast:192.168.0.255 Mask:
    255.255.255.0
    UP BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:904 errors:421 dropped:0 overruns:0 frame:0
    TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:72631 (70.9 Kb) TX bytes:510 (510.0 b)
    Interrupt:209 Base address:0xe800

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:59 errors:0 dropped:0 overruns:0 frame:0
    TX packets:59 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:4156 (4.0 Kb) TX bytes:4156 (4.0 Kb)


    I have used an IP static address, with traditional method ifup
    selected in the YaST utility.

    I do the ifdown of eth0, my network device.

    # ifdown eth0
    eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    compatible 10/100 Ethernet (rev 31)
    eth0 configuration: eth-id-00:08:a1:05:86:d8




    I do an ifup command:

    # ifup eth0
    eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    compatible 10/100 Ethernet (rev 31)
    eth0 configuration: eth-id-00:08:a1:05:86:d8



    And the end look the status:


    # ifstatus eth0
    eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    compatible 10/100 Ethernet (rev 31)
    eth0 configuration: eth-id-00:08:a1:05:86:d8
    eth0 is up
    2: eth0: mtu 1500 qdisc pfifo_fast
    qlen 1000
    link/ether 00:08:a1:05:86:d8 brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.14/24 brd 192.168.0.255 scope global eth0
    eth0 IP address: 192.168.0.14/24
    Configured routes for interface eth0:
    default 192.168.0.1 - -
    169.254.0.0 - 255.255.0.0 eth0
    Active routes for interface eth0:
    192.168.0.0/24 proto kernel scope link src 192.168.0.14
    169.254.0.0/16 scope link
    default via 192.168.0.1
    1 of 2 configured routes for interface eth0 up



    My router is IP:192.168.0.1 and work fine in window and old version of
    SUSE with the same configuration !!! The roting table is:

    # route -n
    Kernel IP routing table
    Destination Gateway Genmask Flags Metric Ref
    Use Iface
    192.168.0.0 0.0.0.0 255.255.255.0 U 0 0
    0 eth0
    169.254.0.0 0.0.0.0 255.255.0.0 U 0 0
    0 eth0
    127.0.0.0 0.0.0.0 255.0.0.0 U 0 0
    0 lo
    0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0
    0 eth0


    I have tried to disable the IPV6 but it's the same.

    When I try to do a ping :

    # ping 192.168.0.14
    PING 192.168.0.14 (192.168.0.14) 56(84) bytes of data.
    64 bytes from 192.168.0.14: icmp_seq=1 ttl=64 time=0.069 ms
    64 bytes from 192.168.0.14: icmp_seq=2 ttl=64 time=0.055 ms
    ....

    Ok, to ping itself work !!!

    When I try to ping my router:

    # ping 192.168.0.1
    PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
    >From 192.168.0.14: icmp_seq=1 Destination Host Unreachable
    >From 192.168.0.14 icmp_seq=1 Destination Host Unreachable
    >From 192.168.0.14 icmp_seq=2 Destination Host Unreachable
    >From 192.168.0.14 icmp_seq=3 Destination Host Unreachable

    ....

    The same thing happen when I try to ping every other machines present
    on my network place.

    If I try to ping it from another machines, seem not present on the
    network.

    Well, hope the somebody can help me to resolve this problem, thank you
    very much..

    Massimo


  2. Re: Network Problem configuration on SUSE 10.2

    On Thu, 07 Jun 2007 11:05:55 +0000, bonchi.massimo wrote:

    > Problem of network configuration
    >
    > Help me please,
    >
    > I have installed the OpenSuSe 10.2, all seem right but I'm not able to
    > connected to any devices in my network space and I'm not able too to
    > going out to internet.
    >
    > I have follow the same procedure of configuration for SUSE 9.3, where
    > all worked fine without any problems.
    >
    > After I have finished to install the new Open SUSE 10.2 I'm not able to
    > connect to the web space.
    >
    > I give some details about my configuration:
    >
    >
    > # ifconfig
    > eth0 Link encap:Ethernet HWaddr 00:08:A1:05:868
    > inet addr:192.168.0.14 Bcast:192.168.0.255 Mask:
    > 255.255.255.0
    > UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:904
    > errors:421 dropped:0 overruns:0 frame:0 TX packets:7 errors:0
    > dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
    > RX bytes:72631 (70.9 Kb) TX bytes:510 (510.0 b) Interrupt:209
    > Base address:0xe800
    >
    > lo Link encap:Local Loopback
    > inet addr:127.0.0.1 Mask:255.0.0.0
    > inet6 addr: ::1/128 Scope:Host
    > UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:59
    > errors:0 dropped:0 overruns:0 frame:0 TX packets:59 errors:0
    > dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
    > RX bytes:4156 (4.0 Kb) TX bytes:4156 (4.0 Kb)
    >
    >
    > I have used an IP static address, with traditional method ifup selected
    > in the YaST utility.
    >
    > I do the ifdown of eth0, my network device.
    >
    > # ifdown eth0
    > eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    > compatible 10/100 Ethernet (rev 31)
    > eth0 configuration: eth-id-00:08:a1:05:86:d8
    >
    >
    >
    >
    > I do an ifup command:
    >
    > # ifup eth0
    > eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    > compatible 10/100 Ethernet (rev 31)
    > eth0 configuration: eth-id-00:08:a1:05:86:d8
    >
    >
    >
    > And the end look the status:
    >
    >
    > # ifstatus eth0
    > eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    > compatible 10/100 Ethernet (rev 31)
    > eth0 configuration: eth-id-00:08:a1:05:86:d8
    > eth0 is up
    > 2: eth0: mtu 1500 qdisc pfifo_fast
    > qlen 1000
    > link/ether 00:08:a1:05:86:d8 brd ff:ff:ff:ff:ff:ff inet
    > 192.168.0.14/24 brd 192.168.0.255 scope global eth0 eth0 IP
    > address: 192.168.0.14/24
    > Configured routes for interface eth0:
    > default 192.168.0.1 - -
    > 169.254.0.0 - 255.255.0.0 eth0
    > Active routes for interface eth0:
    > 192.168.0.0/24 proto kernel scope link src 192.168.0.14
    > 169.254.0.0/16 scope link
    > default via 192.168.0.1
    > 1 of 2 configured routes for interface eth0 up
    >
    >
    >
    > My router is IP:192.168.0.1 and work fine in window and old version of
    > SUSE with the same configuration !!! The roting table is:
    >
    > # route -n
    > Kernel IP routing table
    > Destination Gateway Genmask Flags Metric Ref Use
    > Iface
    > 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
    > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
    > 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
    > 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
    >
    >
    > I have tried to disable the IPV6 but it's the same.
    >
    > When I try to do a ping :
    >
    > # ping 192.168.0.14
    > PING 192.168.0.14 (192.168.0.14) 56(84) bytes of data. 64 bytes from
    > 192.168.0.14: icmp_seq=1 ttl=64 time=0.069 ms 64 bytes from
    > 192.168.0.14: icmp_seq=2 ttl=64 time=0.055 ms ...
    >
    > Ok, to ping itself work !!!
    >
    > When I try to ping my router:
    >
    > # ping 192.168.0.1
    > PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
    >>From 192.168.0.14: icmp_seq=1 Destination Host Unreachable From
    >>192.168.0.14 icmp_seq=1 Destination Host Unreachable From 192.168.0.14
    >>icmp_seq=2 Destination Host Unreachable From 192.168.0.14 icmp_seq=3
    >>Destination Host Unreachable

    > ...
    >
    > The same thing happen when I try to ping every other machines present on
    > my network place.
    >
    > If I try to ping it from another machines, seem not present on the
    > network.
    >
    > Well, hope the somebody can help me to resolve this problem, thank you
    > very much..
    >
    > Massimo



    If you can't ping the router, then try another cable. See if there's green light over the RJ-45 ether cable
    where it is connected at the motherboard.

  3. Re: Network Problem configuration on SUSE 10.2

    On Jun 7, 7:05 am, bonchi.mass...@gmail.com wrote:
    > Problem of network configuration
    >
    > Help me please,
    >
    > I have installed the OpenSuSe 10.2, all seem right but I'm not able to
    > connected to any devices in my network space and I'm not able too to
    > going out to internet.
    >
    > I have follow the same procedure of configuration for SUSE 9.3, where
    > all worked fine without any problems.
    >
    > After I have finished to install the new Open SUSE 10.2 I'm not able
    > to connect to the web space.
    >
    > I give some details about my configuration:
    >
    > # ifconfig
    > eth0 Link encap:Ethernet HWaddr 00:08:A1:05:868
    > inet addr:192.168.0.14 Bcast:192.168.0.255 Mask:
    > 255.255.255.0
    > UP BROADCAST MULTICAST MTU:1500 Metric:1
    > RX packets:904 errors:421 dropped:0 overruns:0 frame:0
    > TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
    > collisions:0 txqueuelen:1000
    > RX bytes:72631 (70.9 Kb) TX bytes:510 (510.0 b)
    > Interrupt:209 Base address:0xe800
    >
    > lo Link encap:Local Loopback
    > inet addr:127.0.0.1 Mask:255.0.0.0
    > inet6 addr: ::1/128 Scope:Host
    > UP LOOPBACK RUNNING MTU:16436 Metric:1
    > RX packets:59 errors:0 dropped:0 overruns:0 frame:0
    > TX packets:59 errors:0 dropped:0 overruns:0 carrier:0
    > collisions:0 txqueuelen:0
    > RX bytes:4156 (4.0 Kb) TX bytes:4156 (4.0 Kb)
    >
    > I have used an IP static address, with traditional method ifup
    > selected in the YaST utility.
    >
    > I do the ifdown of eth0, my network device.
    >
    > # ifdown eth0
    > eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    > compatible 10/100 Ethernet (rev 31)
    > eth0 configuration: eth-id-00:08:a1:05:86:d8
    >
    > I do an ifup command:
    >
    > # ifup eth0
    > eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    > compatible 10/100 Ethernet (rev 31)
    > eth0 configuration: eth-id-00:08:a1:05:86:d8
    >
    > And the end look the status:
    >
    > # ifstatus eth0
    > eth0 device: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
    > compatible 10/100 Ethernet (rev 31)
    > eth0 configuration: eth-id-00:08:a1:05:86:d8
    > eth0 is up
    > 2: eth0: mtu 1500 qdisc pfifo_fast
    > qlen 1000
    > link/ether 00:08:a1:05:86:d8 brd ff:ff:ff:ff:ff:ff
    > inet 192.168.0.14/24 brd 192.168.0.255 scope global eth0
    > eth0 IP address: 192.168.0.14/24
    > Configured routes for interface eth0:
    > default 192.168.0.1 - -
    > 169.254.0.0 - 255.255.0.0 eth0
    > Active routes for interface eth0:
    > 192.168.0.0/24 proto kernel scope link src 192.168.0.14
    > 169.254.0.0/16 scope link
    > default via 192.168.0.1
    > 1 of 2 configured routes for interface eth0 up
    >
    > My router is IP:192.168.0.1 and work fine in window and old version of
    > SUSE with the same configuration !!! The roting table is:
    >
    > # route -n
    > Kernel IP routing table
    > Destination Gateway Genmask Flags Metric Ref
    > Use Iface
    > 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0
    > 0 eth0
    > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0
    > 0 eth0
    > 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0
    > 0 lo
    > 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0
    > 0 eth0
    >
    > I have tried to disable the IPV6 but it's the same.
    >
    > When I try to do a ping :
    >
    > # ping 192.168.0.14
    > PING 192.168.0.14 (192.168.0.14) 56(84) bytes of data.
    > 64 bytes from 192.168.0.14: icmp_seq=1 ttl=64 time=0.069 ms
    > 64 bytes from 192.168.0.14: icmp_seq=2 ttl=64 time=0.055 ms
    > ...
    >
    > Ok, to ping itself work !!!
    >
    > When I try to ping my router:
    >
    > # ping 192.168.0.1
    > PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.>From 192.168.0.14: icmp_seq=1 Destination Host Unreachable
    > >From 192.168.0.14 icmp_seq=1 Destination Host Unreachable
    > >From 192.168.0.14 icmp_seq=2 Destination Host Unreachable
    > >From 192.168.0.14 icmp_seq=3 Destination Host Unreachable

    >
    > ...
    >
    > The same thing happen when I try to ping every other machines present
    > on my network place.
    >
    > If I try to ping it from another machines, seem not present on the
    > network.
    >
    > Well, hope the somebody can help me to resolve this problem, thank you
    > very much..
    >
    > Massimo


    Massimo -- i just got the same thing you did -- at first i thought it
    was the cable, and when i switched it to another port on the switch it
    pinged locally and yahoo.com fine. Then after doing some more (local)
    work -- copying the CDs to a local directory -- i am again cut off and
    decided to google this.

    Must be the NIC, because i have used same CDs for two other stations
    over the last two weeks and all went like greased lightning.

    Now i'm going to learn how to use YaST to replace a NIC(!) -- that is
    unless you or anyone has found a fix?

    br, -craig



+ Reply to Thread