Recovering a broken SNAP server? - Storage

This is a discussion on Recovering a broken SNAP server? - Storage ; I have a SNAP Server which won't reboot properly. Usually it will end up in the Recovery Console. This allows me to Upgrade/Repair my OS (which I've tried but doesn't help) or blow away my data (which I'm loath to ...

+ Reply to Thread
Results 1 to 3 of 3

Thread: Recovering a broken SNAP server?

  1. Recovering a broken SNAP server?

    I have a SNAP Server which won't reboot properly. Usually it will end
    up in the Recovery Console. This allows me to Upgrade/Repair my OS
    (which I've tried but doesn't help) or blow away my data (which I'm
    loath to do).

    So far as I can tell from the diags below it's still able to access the
    filesystems. I'd settle for getting some kind of console access to it
    so that I could extract the data. But it disables the keyboard/screen
    on bootup, and I don't know another way to get into it.

    Any suggestions?


    Snap Server * Recovery




    Diagnostics
    This page shows some basic hardware information which may be useful in
    diagnosing problems with your Snap Server.
    Kernel Version
    3.2.019
    200412142302


    Platform Bytes
    05.01.00


    Model Byte
    06


    Serial Number
    409280


    Bios Stamp
    S18Q3B01


    Failsafe Stamp



    BackplaneHW
    cat: /proc/qinfo/BackplaneHW: No such file or directory


    BackplaneSW
    cat: /proc/qinfo/BackplaneSW: No such file or directory


    Key
    0


    RawE2
    Description Value
    ================= ========================
    MAC Address 00c0b6063ec0
    Compatibility 0000
    Wol 0000
    Controller 01
    Connectors 02
    Primary Phy 4701
    Secondary Phy 0000
    Platform Bytes 255.255.255
    Model Byte 255
    EEPROM ID 4001
    Flags feed
    Subvender f00d

    Struct Version 02
    Server Name 'pop'
    Primary Auto IP 00
    Primary IP 172.21.2.106
    Primary Mask 255.255.0.0
    Primary GW 172.21.1.55
    Primary DHCP 172.19.1.83
    Primary WINS 172.21.2.1
    Primary DNS 172.21.2.1
    Secondary Auto IP 01
    Secondary IP 172.21.10.6
    Secondary Mask 255.255.0.0
    Secondary GW 172.21.1.55
    Secondary WINS 172.21.2.1
    Secondary DNS 172.21.2.1
    Secondary DNS 172.21.2.1

    FS Action Flag 01
    System Config 02
    Diagnostics Flag 00 ff

    Lease Dwords 4223504f 4222fbef 42233b37
    Digest 0000 0000
    Checksum fef2



    Network Address
    cat: /proc/qinfo/NetworkAddress: No such file or directory


    Network devices
    eth0 Link encap:Ethernet HWaddr 00:C0:B6:06:3E:C0
    inet addr:172.21.2.106 Bcast:172.21.255.255
    Mask:255.255.0.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:11685 errors:0 dropped:0 overruns:0 frame:0
    TX packets:4406 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0

    eth1 Link encap:Ethernet HWaddr 00:C0:B6:06:3E:C1
    BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0

    Kernel IP routing table
    Destination Gateway Genmask Flags Metric Ref Use
    Iface
    172.21.0.0 0.0.0.0 255.255.0.0 U 0 0 0
    eth0


    CPU Info
    processor : 0
    vendor_id : GenuineIntel
    cpu family : 15
    model : 2
    model name : Intel(R) Pentium(R) 4 CPU 2.40GHz
    stepping : 9
    branding : 9
    cpu MHz : 2399.401
    L1 cache size : 20 KB
    L2 cache size : 512 KB
    fdiv_bug : no
    hlt_bug : no
    f00f_bug : no
    coma_bug : no
    fpu : yes
    fpu_exception : yes
    cpuid level : 2
    wp : yes
    flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
    pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
    bogomips : 4784.12



    Attached Disks
    Device Model Capacity (sectors)
    hda Maxtor 7Y250P0 490234752
    hdc Maxtor 7Y250P0 490234752
    hde Maxtor 7Y250P0 490234752
    hdg Maxtor 7Y250P0 490234752

    Disk Partitions
    major minor #blocks name

    9 100 546112 md100
    9 101 273024 md101
    34 0 245117376 hdg
    34 1 16041 hdg1
    34 2 546210 hdg2
    34 3 1 hdg3
    34 4 241873915 hdg4
    34 5 273104 hdg5
    34 6 273104 hdg6
    33 0 245117376 hde
    33 1 16041 hde1
    33 2 546210 hde2
    33 3 1 hde3
    33 4 241873915 hde4
    33 5 273104 hde5
    33 6 273104 hde6
    22 0 245117376 hdc
    22 1 16041 hdc1
    22 2 546210 hdc2
    22 3 1 hdc3
    22 4 241873915 hdc4
    22 5 273104 hdc5
    22 6 273104 hdc6
    3 0 245117376 hda
    3 1 16041 hda1
    3 2 546210 hda2
    3 3 1 hda3
    3 4 241873915 hda4
    3 5 273104 hda5
    3 6 273104 hda6

    PCI Devices
    00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32)
    00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge
    00:03.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
    53c896 (rev 07)
    00:03.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
    53c896 (rev 07)
    00:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev
    27)
    00:05.0 IDE interface: CMD Technology Inc: Unknown device 0680 (rev 02)
    00:0f.0 ISA bridge: ServerWorks CSB6 South Bridge (rev a0)
    00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev a0)
    00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05)
    00:0f.3 Host bridge: ServerWorks GCLE-2 Host Bridge
    00:10.0 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit
    Ethernet (rev 12)
    00:10.2 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit
    Ethernet (rev 12)
    02:00.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5704
    Gigabit Ethernet (rev 02)
    02:00.1 Ethernet controller: BROADCOM Corporation NetXtreme BCM5704
    Gigabit Ethernet (rev 02)


    Kernel Boot Messages
    ****************************************** **********************
    ************************************************** **************
    Load Guardian OS...
    VERSION: 3.2.019
    DATE: 200412142302
    ****************************************** **********************
    ************************************************** **************
    Linux version 2.4.19-snap (root@BuildSys) (gcc version
    egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Dec 14
    23:03:28 PST 2004
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001ffff000 (ACPI data)
    BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    On node 0 totalpages: 131056
    zone(0): 4096 pages.
    zone(1): 126960 pages.
    zone(2): 0 pages.
    Kernel command line: root=/dev/ram ramdisk=16384 console=ttyS0,115200n8
    rw
    Initializing CPU#0
    Detected 2399.401 MHz processor.
    Calibrating delay loop... 4784.12 BogoMIPS
    Memory: 512572k/524224k available (1671k kernel code, 11264k reserved,
    341k data, 72k init, 0k highmem)
    Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
    Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
    Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
    CPU: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
    CPU: L1 I cache: 12K, L1 D cache: 8K
    CPU: L2 cache: 512K
    CPU: After vendor init, caps: bfebfbff 00000000 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
    CPU: Common caps: bfebfbff 00000000 00000000 00000000
    CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=2
    PCI: Using configuration type 1
    PCI: Probing PCI hardware
    PCI: Discovered primary peer bus 01 [IRQ]
    PCI: Discovered primary peer bus 02 [IRQ]
    i2c-core.o: i2c core module
    i2c-dev.o: i2c /dev entries driver module
    i2c-core.o: driver i2c-dev dummy driver registered.
    Install SMBus adapter driver (i2c-piix4)
    i2c-dev.o: Registered 'SMBus CSB6 adapter at 0580' as minor 0
    i2c-core.o: adapter SMBus CSB6 adapter at 0580 registered as adapter 0.
    i2c-piix4.o: PIIX4 bus detected and initialized
    i2c-proc.o version 2.6.1 (20010825)
    Qhwif: Found Platform TYPHOON,(ID=402002)
    Qhwif_ACPI: ----- Completed ACPI Initialization -----
    Qhwif: Qhwif proc entries installed OK
    i2c-core.o: driver HDD_LED registered.
    i2c-core.o: client [HDD_LED] registered to adapter [SMBus CSB6 adapter
    at 0580](pos. 0).
    Qhwif: qinfo proc entries installed OK
    Qhwif: Qhwif driver successfully loaded as typhoon driver
    LEDdrv: LED driver successfully loaded as Typhoon driver
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    VFS: Disk quotas vdquot_6.5.1
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    SGI XFS 1.2pre4 with ACLs, quota, no debug enabled
    xnvram: v 2.2 initializing platform ID=402002
    xnvram: installed OK
    Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
    SERIAL_PCI enabled
    ttyS00 at 0x03f8 (irq = 4) is a 16550A
    Non-volatile memory driver v1.1
    QuantaWDT driver registered I/O region 420<6>Uniform Multi-Platform
    E-IDE driver Revision: 6.31
    ide: Assuming 33MHz system bus speed for PIO modes; override with
    idebus=xx
    CMD680: IDE controller on PCI bus 00 dev 28
    CMD680: chipset revision 2
    CMD680: 100% native mode on irq 11
    ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hdaio, hdbio
    ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdcio, hddio
    ServerWorks CSB6: IDE controller on PCI bus 00 dev 79
    ServerWorks CSB6: chipset revision 160
    ServerWorks CSB6: not 100% native mode: will probe irqs later
    ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdeMA, hdfio
    ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdgMA, hdhio
    hda: Maxtor 7Y250P0, ATA DISK drive
    hdc: Maxtor 7Y250P0, ATA DISK drive
    hde: Maxtor 7Y250P0, ATA DISK drive
    hdg: Maxtor 7Y250P0, ATA DISK drive
    ide0 at 0xc400-0xc407,0xc002 on irq 11
    ide1 at 0xb800-0xb807,0xb402 on irq 11
    ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
    ide3 at 0x170-0x177,0x376 on irq 15
    hda: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    hdc: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    hde: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    hdg: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    Partition check:
    hda: hda1 hda2 hda3 < hda5 hda6 > hda4
    hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 > hdc4
    hde: hde1 hde2 hde3 < hde5 hde6 > hde4
    hdg: hdg1 hdg2 hdg3 < hdg5 hdg6 > hdg4
    RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    loop: loaded (max 8 devices)
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: raid1 personality registered as nr 3
    md: raid5 personality registered as nr 4
    raid5: measuring checksumming speed
    8regs : 2363.200 MB/sec
    32regs : 1563.200 MB/sec
    pIII_sse : 3095.600 MB/sec
    pII_mmx : 2847.600 MB/sec
    p5_mmx : 2796.800 MB/sec
    raid5: using function: pIII_sse (3095.600 MB/sec)
    md: spare personality registered as nr 8
    md: md driver 0.91.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    LVM version 1.0.6(25/10/2002)
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 4096 buckets, 32Kbytes
    TCP: Hash tables configured (established 32768 bind 32768)
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Linux IPX 0.47 for NET4.0
    IPX Portions Copyright (c) 1995 Caldera, Inc.
    IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
    NET4: AppleTalk 0.18a for Linux NET4.0
    RAMDISK: Compressed image found at block 0
    Freeing initrd memory: 2734k freed
    EXT2-fs warning: checktime reached, running e2fsck is recommended
    VFS: Mounted root (ext2 filesystem).
    Freeing unused kernel memory: 72k freed
    init_guardianflash_mtd: Found Quanta Platform
    Guardian.0: Found 1 x 512KiB AMD AM29F004BT at 0x0
    SCSI subsystem driver Revision: 1.00
    sym.0.3.1: setting PCI_COMMAND_PARITY...
    sym.0.3.0: setting PCI_COMMAND_PARITY...
    sym0: <896> rev 0x7 on pci bus 0 device 3 function 1 irq 3
    sym0: using 64 bit DMA addressing
    sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
    sym0: open drain IRQ line driver, using on-chip SRAM
    sym0: using LOAD/STORE-based firmware.
    sym0: handling phase mismatch from SCRIPTS.
    sym0: SCSI BUS has been reset.
    sym1: <896> rev 0x7 on pci bus 0 device 3 function 0 irq 7
    sym1: using 64 bit DMA addressing
    sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
    sym1: open drain IRQ line driver, using on-chip SRAM
    sym1: using LOAD/STORE-based firmware.
    sym1: handling phase mismatch from SCRIPTS.
    sym1: SCSI BUS has been reset.
    scsi0 : sym-2.1.17a
    scsi1 : sym-2.1.17a
    i2c-core.o: driver Qhwmon registered.
    i2c-core.o: client [Qhwmon] registered to adapter [SMBus CSB6 adapter
    at 0580](pos. 1).
    Qhwmon: proc entries installed OK
    Qhwmon: ExpUnit setup skipped!
    Qhwmon: Hardware monitor driver successfully loaded as Typhoon driver
    Qinfo: i2c driver attached, getting eeprom image
    Qinfo: E1 csum = E2 csum and both good
    Qinfo: eeprom image received.
    Qinfo: Reading from EEPROM... CheckSum = 0000
    Qinfo:0000: 00 c0 b6 06 3e c0 00 00 00 00 01 02 01 47 00 00
    .....>........G..
    Qinfo:0010: ff ff ff ff 01 40 ed fe 0d f0 02 70 6f 70 00 00
    ......@.....pop..
    Qinfo:0020: 00 00 00 00 00 00 00 00 00 00 00 ac 15 02 6a ff
    ...............j.
    Qinfo:0030: ff 00 00 ac 15 01 37 ac 13 01 53 ac 15 02 01 ac
    .......7...S.....
    Qinfo:0040: 15 02 01 00 ac 15 0a 06 ff ff 00 00 ac 15 01 37
    ................7
    Qinfo:0050: ac 15 02 01 ac 15 02 01 01 4f 50 23 42 ef fb 22
    ..........OP#B.."
    Qinfo:0060: 42 37 3b 23 42 01 01 02 00 ff 00 00 00 00 00 00
    B7;#B...........
    Qinfo:0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f2 fe
    .................
    Qinfo: Bios Version: :S18Q3B01:
    [events: 0000006f]
    md: bind
    [events: 0000006f]
    md: bind
    [events: 0000006f]
    md: bind
    [events: 0000006f]
    md: bind
    md: hda2's event counter: 0000006f
    md: hde2's event counter: 0000006f
    md: hdg2's event counter: 0000006f
    md: hdc2's event counter: 0000006f
    md: md100: raid array is not clean -- starting background
    reconstruction
    md: RAID level 1 does not need chunksize! Continuing anyway.
    md100: max total readahead window set to 124k
    md100: 1 data-disks, max readahead per data-disk: 124k
    raid1: device hda2 operational as mirror 0
    raid1: device hde2 operational as mirror 3
    raid1: device hdg2 operational as mirror 2
    raid1: device hdc2 operational as mirror 1
    raid1: raid set md100 not clean; reconstructing mirrors
    raid1: raid set md100 active with 4 out of 4 mirrors
    md: updating md100 RAID superblock on device
    md: hda2 [events: 00000070]<6>(write) hda2's sb offset: 546112
    md: syncing RAID array md100
    md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
    md: using maximum available idle IO bandwith (but not more than 100000
    KB/sec) for reconstruction.
    md: using 124k window, over a total of 546112 blocks.
    md: hde2 [events: 00000070]<6>(write) hde2's sb offset: 546112
    md: hdg2 [events: 00000070]<6>(write) hdg2's sb offset: 546112
    md: hdc2 [events: 00000070]<6>(write) hdc2's sb offset: 546112
    [events: 00000071]
    md: bind
    [events: 00000071]
    md: bind
    [events: 00000071]
    md: bind
    [events: 00000071]
    md: bind
    md: hda5's event counter: 00000071
    md: hdc5's event counter: 00000071
    md: hde5's event counter: 00000071
    md: hdg5's event counter: 00000071
    md: md101: raid array is not clean -- starting background
    reconstruction
    md: RAID level 1 does not need chunksize! Continuing anyway.
    md101: max total readahead window set to 124k
    md101: 1 data-disks, max readahead per data-disk: 124k
    raid1: device hda5 operational as mirror 0
    raid1: device hdc5 operational as mirror 3
    raid1: device hde5 operational as mirror 2
    raid1: device hdg5 operational as mirror 1
    raid1: raid set md101 not clean; reconstructing mirrors
    raid1: raid set md101 active with 4 out of 4 mirrors
    md: updating md101 RAID superblock on device
    md: hda5 [events: 00000072]<6>(write) hda5's sb offset: 273024
    md: delaying resync of md101 until md100 has finished resync (they
    share one or more physical units)
    md: hdc5 [events: 00000072]<6>(write) hdc5's sb offset: 273024
    md: hde5 [events: 00000072]<6>(write) hde5's sb offset: 273024
    md: hdg5 [events: 00000072]<6>(write) hdg5's sb offset: 273024
    XFS mounting filesystem md(9,100)
    Starting XFS recovery on filesystem: md(9,100) (dev: 9/100)
    Ending XFS recovery on filesystem: md(9,100) (dev: 9/100)

    SnapNIC: found MAC 0xc0b6063ec1
    ,<5>
    SnapNIC: found MAC 0xc0b6063ec0
    ,<5>SnapNIC: Found all NICs (2)
    SnapNIC: Register 2 NIC devices sorted by MAC
    Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension
    (NICE) ver. 7.0.0 (08/14/03)
    eth0: Broadcom BCM5704 1000Base-T found at mem febd0000, IRQ 5, node
    addr 00c0b6063ec0
    eth0: Broadcom BCM5704 Integrated Copper transceiver found
    eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
    802.1Q VLAN ON
    eth1: Broadcom BCM5704 1000Base-T found at mem febf0000, IRQ 9, node
    addr 00c0b6063ec1
    eth1: Broadcom BCM5704 Integrated Copper transceiver found
    eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
    802.1Q VLAN ON
    xnvram: CMOS is currently locked.
    Qinfo: valid key presented - eeprom unlocked
    Qinfo: Key 0 - Locking eeprom
    Qhwif: Enable watchdog management- 30 min timeout
    bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit
    flow control ON
    xnvram: i=0 bcount[0]=5
    xnvram: i=0 bcount[0]=5
    md: md100: sync done.
    md: syncing RAID array md101
    md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
    md: using maximum available idle IO bandwith (but not more than 100000
    KB/sec) for reconstruction.
    md: using 124k window, over a total of 273024 blocks.
    md: md101: sync done.


  2. Re: Recovering a broken SNAP server?

    Well, I can attach a USB floppy. But I'd need the right boot image for the
    floppy, I think?

    wrote in message
    news:1132579495.082558.147570@g49g2000cwa.googlegr oups.com...
    I have a SNAP Server which won't reboot properly. Usually it will end
    up in the Recovery Console. This allows me to Upgrade/Repair my OS
    (which I've tried but doesn't help) or blow away my data (which I'm
    loath to do).

    So far as I can tell from the diags below it's still able to access the
    filesystems. I'd settle for getting some kind of console access to it
    so that I could extract the data. But it disables the keyboard/screen
    on bootup, and I don't know another way to get into it.

    Any suggestions?


    Snap Server * Recovery




    Diagnostics
    This page shows some basic hardware information which may be useful in
    diagnosing problems with your Snap Server.
    Kernel Version
    3.2.019
    200412142302


    Platform Bytes
    05.01.00


    Model Byte
    06


    Serial Number
    409280


    Bios Stamp
    S18Q3B01


    Failsafe Stamp



    BackplaneHW
    cat: /proc/qinfo/BackplaneHW: No such file or directory


    BackplaneSW
    cat: /proc/qinfo/BackplaneSW: No such file or directory


    Key
    0


    RawE2
    Description Value
    ================= ========================
    MAC Address 00c0b6063ec0
    Compatibility 0000
    Wol 0000
    Controller 01
    Connectors 02
    Primary Phy 4701
    Secondary Phy 0000
    Platform Bytes 255.255.255
    Model Byte 255
    EEPROM ID 4001
    Flags feed
    Subvender f00d

    Struct Version 02
    Server Name 'pop'
    Primary Auto IP 00
    Primary IP 172.21.2.106
    Primary Mask 255.255.0.0
    Primary GW 172.21.1.55
    Primary DHCP 172.19.1.83
    Primary WINS 172.21.2.1
    Primary DNS 172.21.2.1
    Secondary Auto IP 01
    Secondary IP 172.21.10.6
    Secondary Mask 255.255.0.0
    Secondary GW 172.21.1.55
    Secondary WINS 172.21.2.1
    Secondary DNS 172.21.2.1
    Secondary DNS 172.21.2.1

    FS Action Flag 01
    System Config 02
    Diagnostics Flag 00 ff

    Lease Dwords 4223504f 4222fbef 42233b37
    Digest 0000 0000
    Checksum fef2



    Network Address
    cat: /proc/qinfo/NetworkAddress: No such file or directory


    Network devices
    eth0 Link encap:Ethernet HWaddr 00:C0:B6:06:3E:C0
    inet addr:172.21.2.106 Bcast:172.21.255.255
    Mask:255.255.0.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:11685 errors:0 dropped:0 overruns:0 frame:0
    TX packets:4406 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0

    eth1 Link encap:Ethernet HWaddr 00:C0:B6:06:3E:C1
    BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0

    Kernel IP routing table
    Destination Gateway Genmask Flags Metric Ref Use
    Iface
    172.21.0.0 0.0.0.0 255.255.0.0 U 0 0 0
    eth0


    CPU Info
    processor : 0
    vendor_id : GenuineIntel
    cpu family : 15
    model : 2
    model name : Intel(R) Pentium(R) 4 CPU 2.40GHz
    stepping : 9
    branding : 9
    cpu MHz : 2399.401
    L1 cache size : 20 KB
    L2 cache size : 512 KB
    fdiv_bug : no
    hlt_bug : no
    f00f_bug : no
    coma_bug : no
    fpu : yes
    fpu_exception : yes
    cpuid level : 2
    wp : yes
    flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
    pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
    bogomips : 4784.12



    Attached Disks
    Device Model Capacity (sectors)
    hda Maxtor 7Y250P0 490234752
    hdc Maxtor 7Y250P0 490234752
    hde Maxtor 7Y250P0 490234752
    hdg Maxtor 7Y250P0 490234752

    Disk Partitions
    major minor #blocks name

    9 100 546112 md100
    9 101 273024 md101
    34 0 245117376 hdg
    34 1 16041 hdg1
    34 2 546210 hdg2
    34 3 1 hdg3
    34 4 241873915 hdg4
    34 5 273104 hdg5
    34 6 273104 hdg6
    33 0 245117376 hde
    33 1 16041 hde1
    33 2 546210 hde2
    33 3 1 hde3
    33 4 241873915 hde4
    33 5 273104 hde5
    33 6 273104 hde6
    22 0 245117376 hdc
    22 1 16041 hdc1
    22 2 546210 hdc2
    22 3 1 hdc3
    22 4 241873915 hdc4
    22 5 273104 hdc5
    22 6 273104 hdc6
    3 0 245117376 hda
    3 1 16041 hda1
    3 2 546210 hda2
    3 3 1 hda3
    3 4 241873915 hda4
    3 5 273104 hda5
    3 6 273104 hda6

    PCI Devices
    00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32)
    00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge
    00:03.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
    53c896 (rev 07)
    00:03.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
    53c896 (rev 07)
    00:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev
    27)
    00:05.0 IDE interface: CMD Technology Inc: Unknown device 0680 (rev 02)
    00:0f.0 ISA bridge: ServerWorks CSB6 South Bridge (rev a0)
    00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev a0)
    00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05)
    00:0f.3 Host bridge: ServerWorks GCLE-2 Host Bridge
    00:10.0 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit
    Ethernet (rev 12)
    00:10.2 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit
    Ethernet (rev 12)
    02:00.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5704
    Gigabit Ethernet (rev 02)
    02:00.1 Ethernet controller: BROADCOM Corporation NetXtreme BCM5704
    Gigabit Ethernet (rev 02)


    Kernel Boot Messages
    ****************************************** **********************
    ************************************************** **************
    Load Guardian OS...
    VERSION: 3.2.019
    DATE: 200412142302
    ****************************************** **********************
    ************************************************** **************
    Linux version 2.4.19-snap (root@BuildSys) (gcc version
    egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Dec 14
    23:03:28 PST 2004
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001ffff000 (ACPI data)
    BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
    BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    On node 0 totalpages: 131056
    zone(0): 4096 pages.
    zone(1): 126960 pages.
    zone(2): 0 pages.
    Kernel command line: root=/dev/ram ramdisk=16384 console=ttyS0,115200n8
    rw
    Initializing CPU#0
    Detected 2399.401 MHz processor.
    Calibrating delay loop... 4784.12 BogoMIPS
    Memory: 512572k/524224k available (1671k kernel code, 11264k reserved,
    341k data, 72k init, 0k highmem)
    Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
    Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
    Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
    CPU: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
    CPU: L1 I cache: 12K, L1 D cache: 8K
    CPU: L2 cache: 512K
    CPU: After vendor init, caps: bfebfbff 00000000 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
    CPU: Common caps: bfebfbff 00000000 00000000 00000000
    CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=2
    PCI: Using configuration type 1
    PCI: Probing PCI hardware
    PCI: Discovered primary peer bus 01 [IRQ]
    PCI: Discovered primary peer bus 02 [IRQ]
    i2c-core.o: i2c core module
    i2c-dev.o: i2c /dev entries driver module
    i2c-core.o: driver i2c-dev dummy driver registered.
    Install SMBus adapter driver (i2c-piix4)
    i2c-dev.o: Registered 'SMBus CSB6 adapter at 0580' as minor 0
    i2c-core.o: adapter SMBus CSB6 adapter at 0580 registered as adapter 0.
    i2c-piix4.o: PIIX4 bus detected and initialized
    i2c-proc.o version 2.6.1 (20010825)
    Qhwif: Found Platform TYPHOON,(ID=402002)
    Qhwif_ACPI: ----- Completed ACPI Initialization -----
    Qhwif: Qhwif proc entries installed OK
    i2c-core.o: driver HDD_LED registered.
    i2c-core.o: client [HDD_LED] registered to adapter [SMBus CSB6 adapter
    at 0580](pos. 0).
    Qhwif: qinfo proc entries installed OK
    Qhwif: Qhwif driver successfully loaded as typhoon driver
    LEDdrv: LED driver successfully loaded as Typhoon driver
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    VFS: Disk quotas vdquot_6.5.1
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    SGI XFS 1.2pre4 with ACLs, quota, no debug enabled
    xnvram: v 2.2 initializing platform ID=402002
    xnvram: installed OK
    Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
    SERIAL_PCI enabled
    ttyS00 at 0x03f8 (irq = 4) is a 16550A
    Non-volatile memory driver v1.1
    QuantaWDT driver registered I/O region 420<6>Uniform Multi-Platform
    E-IDE driver Revision: 6.31
    ide: Assuming 33MHz system bus speed for PIO modes; override with
    idebus=xx
    CMD680: IDE controller on PCI bus 00 dev 28
    CMD680: chipset revision 2
    CMD680: 100% native mode on irq 11
    ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hdaio, hdbio
    ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdcio, hddio
    ServerWorks CSB6: IDE controller on PCI bus 00 dev 79
    ServerWorks CSB6: chipset revision 160
    ServerWorks CSB6: not 100% native mode: will probe irqs later
    ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdeMA, hdfio
    ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdgMA, hdhio
    hda: Maxtor 7Y250P0, ATA DISK drive
    hdc: Maxtor 7Y250P0, ATA DISK drive
    hde: Maxtor 7Y250P0, ATA DISK drive
    hdg: Maxtor 7Y250P0, ATA DISK drive
    ide0 at 0xc400-0xc407,0xc002 on irq 11
    ide1 at 0xb800-0xb807,0xb402 on irq 11
    ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
    ide3 at 0x170-0x177,0x376 on irq 15
    hda: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    hdc: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    hde: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    hdg: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    UDMA(100)
    Partition check:
    hda: hda1 hda2 hda3 < hda5 hda6 > hda4
    hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 > hdc4
    hde: hde1 hde2 hde3 < hde5 hde6 > hde4
    hdg: hdg1 hdg2 hdg3 < hdg5 hdg6 > hdg4
    RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    loop: loaded (max 8 devices)
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: raid1 personality registered as nr 3
    md: raid5 personality registered as nr 4
    raid5: measuring checksumming speed
    8regs : 2363.200 MB/sec
    32regs : 1563.200 MB/sec
    pIII_sse : 3095.600 MB/sec
    pII_mmx : 2847.600 MB/sec
    p5_mmx : 2796.800 MB/sec
    raid5: using function: pIII_sse (3095.600 MB/sec)
    md: spare personality registered as nr 8
    md: md driver 0.91.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    LVM version 1.0.6(25/10/2002)
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 4096 buckets, 32Kbytes
    TCP: Hash tables configured (established 32768 bind 32768)
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Linux IPX 0.47 for NET4.0
    IPX Portions Copyright (c) 1995 Caldera, Inc.
    IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
    NET4: AppleTalk 0.18a for Linux NET4.0
    RAMDISK: Compressed image found at block 0
    Freeing initrd memory: 2734k freed
    EXT2-fs warning: checktime reached, running e2fsck is recommended
    VFS: Mounted root (ext2 filesystem).
    Freeing unused kernel memory: 72k freed
    init_guardianflash_mtd: Found Quanta Platform
    Guardian.0: Found 1 x 512KiB AMD AM29F004BT at 0x0
    SCSI subsystem driver Revision: 1.00
    sym.0.3.1: setting PCI_COMMAND_PARITY...
    sym.0.3.0: setting PCI_COMMAND_PARITY...
    sym0: <896> rev 0x7 on pci bus 0 device 3 function 1 irq 3
    sym0: using 64 bit DMA addressing
    sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
    sym0: open drain IRQ line driver, using on-chip SRAM
    sym0: using LOAD/STORE-based firmware.
    sym0: handling phase mismatch from SCRIPTS.
    sym0: SCSI BUS has been reset.
    sym1: <896> rev 0x7 on pci bus 0 device 3 function 0 irq 7
    sym1: using 64 bit DMA addressing
    sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
    sym1: open drain IRQ line driver, using on-chip SRAM
    sym1: using LOAD/STORE-based firmware.
    sym1: handling phase mismatch from SCRIPTS.
    sym1: SCSI BUS has been reset.
    scsi0 : sym-2.1.17a
    scsi1 : sym-2.1.17a
    i2c-core.o: driver Qhwmon registered.
    i2c-core.o: client [Qhwmon] registered to adapter [SMBus CSB6 adapter
    at 0580](pos. 1).
    Qhwmon: proc entries installed OK
    Qhwmon: ExpUnit setup skipped!
    Qhwmon: Hardware monitor driver successfully loaded as Typhoon driver
    Qinfo: i2c driver attached, getting eeprom image
    Qinfo: E1 csum = E2 csum and both good
    Qinfo: eeprom image received.
    Qinfo: Reading from EEPROM... CheckSum = 0000
    Qinfo:0000: 00 c0 b6 06 3e c0 00 00 00 00 01 02 01 47 00 00
    .....>........G..
    Qinfo:0010: ff ff ff ff 01 40 ed fe 0d f0 02 70 6f 70 00 00
    ......@.....pop..
    Qinfo:0020: 00 00 00 00 00 00 00 00 00 00 00 ac 15 02 6a ff
    ...............j.
    Qinfo:0030: ff 00 00 ac 15 01 37 ac 13 01 53 ac 15 02 01 ac
    .......7...S.....
    Qinfo:0040: 15 02 01 00 ac 15 0a 06 ff ff 00 00 ac 15 01 37
    ................7
    Qinfo:0050: ac 15 02 01 ac 15 02 01 01 4f 50 23 42 ef fb 22
    ..........OP#B.."
    Qinfo:0060: 42 37 3b 23 42 01 01 02 00 ff 00 00 00 00 00 00
    B7;#B...........
    Qinfo:0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f2 fe
    .................
    Qinfo: Bios Version: :S18Q3B01:
    [events: 0000006f]
    md: bind
    [events: 0000006f]
    md: bind
    [events: 0000006f]
    md: bind
    [events: 0000006f]
    md: bind
    md: hda2's event counter: 0000006f
    md: hde2's event counter: 0000006f
    md: hdg2's event counter: 0000006f
    md: hdc2's event counter: 0000006f
    md: md100: raid array is not clean -- starting background
    reconstruction
    md: RAID level 1 does not need chunksize! Continuing anyway.
    md100: max total readahead window set to 124k
    md100: 1 data-disks, max readahead per data-disk: 124k
    raid1: device hda2 operational as mirror 0
    raid1: device hde2 operational as mirror 3
    raid1: device hdg2 operational as mirror 2
    raid1: device hdc2 operational as mirror 1
    raid1: raid set md100 not clean; reconstructing mirrors
    raid1: raid set md100 active with 4 out of 4 mirrors
    md: updating md100 RAID superblock on device
    md: hda2 [events: 00000070]<6>(write) hda2's sb offset: 546112
    md: syncing RAID array md100
    md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
    md: using maximum available idle IO bandwith (but not more than 100000
    KB/sec) for reconstruction.
    md: using 124k window, over a total of 546112 blocks.
    md: hde2 [events: 00000070]<6>(write) hde2's sb offset: 546112
    md: hdg2 [events: 00000070]<6>(write) hdg2's sb offset: 546112
    md: hdc2 [events: 00000070]<6>(write) hdc2's sb offset: 546112
    [events: 00000071]
    md: bind
    [events: 00000071]
    md: bind
    [events: 00000071]
    md: bind
    [events: 00000071]
    md: bind
    md: hda5's event counter: 00000071
    md: hdc5's event counter: 00000071
    md: hde5's event counter: 00000071
    md: hdg5's event counter: 00000071
    md: md101: raid array is not clean -- starting background
    reconstruction
    md: RAID level 1 does not need chunksize! Continuing anyway.
    md101: max total readahead window set to 124k
    md101: 1 data-disks, max readahead per data-disk: 124k
    raid1: device hda5 operational as mirror 0
    raid1: device hdc5 operational as mirror 3
    raid1: device hde5 operational as mirror 2
    raid1: device hdg5 operational as mirror 1
    raid1: raid set md101 not clean; reconstructing mirrors
    raid1: raid set md101 active with 4 out of 4 mirrors
    md: updating md101 RAID superblock on device
    md: hda5 [events: 00000072]<6>(write) hda5's sb offset: 273024
    md: delaying resync of md101 until md100 has finished resync (they
    share one or more physical units)
    md: hdc5 [events: 00000072]<6>(write) hdc5's sb offset: 273024
    md: hde5 [events: 00000072]<6>(write) hde5's sb offset: 273024
    md: hdg5 [events: 00000072]<6>(write) hdg5's sb offset: 273024
    XFS mounting filesystem md(9,100)
    Starting XFS recovery on filesystem: md(9,100) (dev: 9/100)
    Ending XFS recovery on filesystem: md(9,100) (dev: 9/100)

    SnapNIC: found MAC 0xc0b6063ec1
    ,<5>
    SnapNIC: found MAC 0xc0b6063ec0
    ,<5>SnapNIC: Found all NICs (2)
    SnapNIC: Register 2 NIC devices sorted by MAC
    Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension
    (NICE) ver. 7.0.0 (08/14/03)
    eth0: Broadcom BCM5704 1000Base-T found at mem febd0000, IRQ 5, node
    addr 00c0b6063ec0
    eth0: Broadcom BCM5704 Integrated Copper transceiver found
    eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
    802.1Q VLAN ON
    eth1: Broadcom BCM5704 1000Base-T found at mem febf0000, IRQ 9, node
    addr 00c0b6063ec1
    eth1: Broadcom BCM5704 Integrated Copper transceiver found
    eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
    802.1Q VLAN ON
    xnvram: CMOS is currently locked.
    Qinfo: valid key presented - eeprom unlocked
    Qinfo: Key 0 - Locking eeprom
    Qhwif: Enable watchdog management- 30 min timeout
    bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit
    flow control ON
    xnvram: i=0 bcount[0]=5
    xnvram: i=0 bcount[0]=5
    md: md100: sync done.
    md: syncing RAID array md101
    md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
    md: using maximum available idle IO bandwith (but not more than 100000
    KB/sec) for reconstruction.
    md: using 124k window, over a total of 273024 blocks.
    md: md101: sync done.



  3. Re: Recovering a broken SNAP server?

    So, I can attach a USB floppy, boot up, and see the top-level OS partition
    with the kernel on it. But I can't mount any of the other file systems,
    perhaps because they're RAID.

    It also looks like the stuff that disables the keyboard/screen is actually
    built into the kernel - so there's not much scope of stopping it doing that.

    "News" wrote in message
    news:43875118$0$23983$4d4eb98e@read.news.uk.uu.net ...
    > Well, I can attach a USB floppy. But I'd need the right boot image for

    the
    > floppy, I think?
    >
    > wrote in message
    > news:1132579495.082558.147570@g49g2000cwa.googlegr oups.com...
    > I have a SNAP Server which won't reboot properly. Usually it will end
    > up in the Recovery Console. This allows me to Upgrade/Repair my OS
    > (which I've tried but doesn't help) or blow away my data (which I'm
    > loath to do).
    >
    > So far as I can tell from the diags below it's still able to access the
    > filesystems. I'd settle for getting some kind of console access to it
    > so that I could extract the data. But it disables the keyboard/screen
    > on bootup, and I don't know another way to get into it.
    >
    > Any suggestions?
    >
    >
    > Snap Server * Recovery
    >
    >
    >
    >
    > Diagnostics
    > This page shows some basic hardware information which may be useful in
    > diagnosing problems with your Snap Server.
    > Kernel Version
    > 3.2.019
    > 200412142302
    >
    >
    > Platform Bytes
    > 05.01.00
    >
    >
    > Model Byte
    > 06
    >
    >
    > Serial Number
    > 409280
    >
    >
    > Bios Stamp
    > S18Q3B01
    >
    >
    > Failsafe Stamp
    >
    >
    >
    > BackplaneHW
    > cat: /proc/qinfo/BackplaneHW: No such file or directory
    >
    >
    > BackplaneSW
    > cat: /proc/qinfo/BackplaneSW: No such file or directory
    >
    >
    > Key
    > 0
    >
    >
    > RawE2
    > Description Value
    > ================= ========================
    > MAC Address 00c0b6063ec0
    > Compatibility 0000
    > Wol 0000
    > Controller 01
    > Connectors 02
    > Primary Phy 4701
    > Secondary Phy 0000
    > Platform Bytes 255.255.255
    > Model Byte 255
    > EEPROM ID 4001
    > Flags feed
    > Subvender f00d
    >
    > Struct Version 02
    > Server Name 'pop'
    > Primary Auto IP 00
    > Primary IP 172.21.2.106
    > Primary Mask 255.255.0.0
    > Primary GW 172.21.1.55
    > Primary DHCP 172.19.1.83
    > Primary WINS 172.21.2.1
    > Primary DNS 172.21.2.1
    > Secondary Auto IP 01
    > Secondary IP 172.21.10.6
    > Secondary Mask 255.255.0.0
    > Secondary GW 172.21.1.55
    > Secondary WINS 172.21.2.1
    > Secondary DNS 172.21.2.1
    > Secondary DNS 172.21.2.1
    >
    > FS Action Flag 01
    > System Config 02
    > Diagnostics Flag 00 ff
    >
    > Lease Dwords 4223504f 4222fbef 42233b37
    > Digest 0000 0000
    > Checksum fef2
    >
    >
    >
    > Network Address
    > cat: /proc/qinfo/NetworkAddress: No such file or directory
    >
    >
    > Network devices
    > eth0 Link encap:Ethernet HWaddr 00:C0:B6:06:3E:C0
    > inet addr:172.21.2.106 Bcast:172.21.255.255
    > Mask:255.255.0.0
    > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    > RX packets:11685 errors:0 dropped:0 overruns:0 frame:0
    > TX packets:4406 errors:0 dropped:0 overruns:0 carrier:0
    > collisions:0
    >
    > eth1 Link encap:Ethernet HWaddr 00:C0:B6:06:3E:C1
    > BROADCAST MULTICAST MTU:1500 Metric:1
    > RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    > collisions:0
    >
    > lo Link encap:Local Loopback
    > inet addr:127.0.0.1 Mask:255.0.0.0
    > UP LOOPBACK RUNNING MTU:16436 Metric:1
    > RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    > collisions:0
    >
    > Kernel IP routing table
    > Destination Gateway Genmask Flags Metric Ref Use
    > Iface
    > 172.21.0.0 0.0.0.0 255.255.0.0 U 0 0 0
    > eth0
    >
    >
    > CPU Info
    > processor : 0
    > vendor_id : GenuineIntel
    > cpu family : 15
    > model : 2
    > model name : Intel(R) Pentium(R) 4 CPU 2.40GHz
    > stepping : 9
    > branding : 9
    > cpu MHz : 2399.401
    > L1 cache size : 20 KB
    > L2 cache size : 512 KB
    > fdiv_bug : no
    > hlt_bug : no
    > f00f_bug : no
    > coma_bug : no
    > fpu : yes
    > fpu_exception : yes
    > cpuid level : 2
    > wp : yes
    > flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
    > pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
    > bogomips : 4784.12
    >
    >
    >
    > Attached Disks
    > Device Model Capacity (sectors)
    > hda Maxtor 7Y250P0 490234752
    > hdc Maxtor 7Y250P0 490234752
    > hde Maxtor 7Y250P0 490234752
    > hdg Maxtor 7Y250P0 490234752
    >
    > Disk Partitions
    > major minor #blocks name
    >
    > 9 100 546112 md100
    > 9 101 273024 md101
    > 34 0 245117376 hdg
    > 34 1 16041 hdg1
    > 34 2 546210 hdg2
    > 34 3 1 hdg3
    > 34 4 241873915 hdg4
    > 34 5 273104 hdg5
    > 34 6 273104 hdg6
    > 33 0 245117376 hde
    > 33 1 16041 hde1
    > 33 2 546210 hde2
    > 33 3 1 hde3
    > 33 4 241873915 hde4
    > 33 5 273104 hde5
    > 33 6 273104 hde6
    > 22 0 245117376 hdc
    > 22 1 16041 hdc1
    > 22 2 546210 hdc2
    > 22 3 1 hdc3
    > 22 4 241873915 hdc4
    > 22 5 273104 hdc5
    > 22 6 273104 hdc6
    > 3 0 245117376 hda
    > 3 1 16041 hda1
    > 3 2 546210 hda2
    > 3 3 1 hda3
    > 3 4 241873915 hda4
    > 3 5 273104 hda5
    > 3 6 273104 hda6
    >
    > PCI Devices
    > 00:00.0 Host bridge: ServerWorks GCNB-LE Host Bridge (rev 32)
    > 00:00.1 Host bridge: ServerWorks GCNB-LE Host Bridge
    > 00:03.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
    > 53c896 (rev 07)
    > 00:03.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
    > 53c896 (rev 07)
    > 00:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev
    > 27)
    > 00:05.0 IDE interface: CMD Technology Inc: Unknown device 0680 (rev 02)
    > 00:0f.0 ISA bridge: ServerWorks CSB6 South Bridge (rev a0)
    > 00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev a0)
    > 00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05)
    > 00:0f.3 Host bridge: ServerWorks GCLE-2 Host Bridge
    > 00:10.0 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit
    > Ethernet (rev 12)
    > 00:10.2 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit
    > Ethernet (rev 12)
    > 02:00.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5704
    > Gigabit Ethernet (rev 02)
    > 02:00.1 Ethernet controller: BROADCOM Corporation NetXtreme BCM5704
    > Gigabit Ethernet (rev 02)
    >
    >
    > Kernel Boot Messages
    > ****************************************** **********************
    > ************************************************** **************
    > Load Guardian OS...
    > VERSION: 3.2.019
    > DATE: 200412142302
    > ****************************************** **********************
    > ************************************************** **************
    > Linux version 2.4.19-snap (root@BuildSys) (gcc version
    > egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Dec 14
    > 23:03:28 PST 2004
    > BIOS-provided physical RAM map:
    > BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    > BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    > BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    > BIOS-e820: 000000001fff0000 - 000000001ffff000 (ACPI data)
    > BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
    > BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
    > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    > 0MB HIGHMEM available.
    > 511MB LOWMEM available.
    > On node 0 totalpages: 131056
    > zone(0): 4096 pages.
    > zone(1): 126960 pages.
    > zone(2): 0 pages.
    > Kernel command line: root=/dev/ram ramdisk=16384 console=ttyS0,115200n8
    > rw
    > Initializing CPU#0
    > Detected 2399.401 MHz processor.
    > Calibrating delay loop... 4784.12 BogoMIPS
    > Memory: 512572k/524224k available (1671k kernel code, 11264k reserved,
    > 341k data, 72k init, 0k highmem)
    > Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
    > Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
    > Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    > Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
    > Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
    > CPU: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
    > CPU: L1 I cache: 12K, L1 D cache: 8K
    > CPU: L2 cache: 512K
    > CPU: After vendor init, caps: bfebfbff 00000000 00000000 00000000
    > Intel machine check architecture supported.
    > Intel machine check reporting enabled on CPU#0.
    > CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
    > CPU: Common caps: bfebfbff 00000000 00000000 00000000
    > CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
    > Enabling fast FPU save and restore... done.
    > Enabling unmasked SIMD FPU exception support... done.
    > Checking 'hlt' instruction... OK.
    > POSIX conformance testing by UNIFIX
    > PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=2
    > PCI: Using configuration type 1
    > PCI: Probing PCI hardware
    > PCI: Discovered primary peer bus 01 [IRQ]
    > PCI: Discovered primary peer bus 02 [IRQ]
    > i2c-core.o: i2c core module
    > i2c-dev.o: i2c /dev entries driver module
    > i2c-core.o: driver i2c-dev dummy driver registered.
    > Install SMBus adapter driver (i2c-piix4)
    > i2c-dev.o: Registered 'SMBus CSB6 adapter at 0580' as minor 0
    > i2c-core.o: adapter SMBus CSB6 adapter at 0580 registered as adapter 0.
    > i2c-piix4.o: PIIX4 bus detected and initialized
    > i2c-proc.o version 2.6.1 (20010825)
    > Qhwif: Found Platform TYPHOON,(ID=402002)
    > Qhwif_ACPI: ----- Completed ACPI Initialization -----
    > Qhwif: Qhwif proc entries installed OK
    > i2c-core.o: driver HDD_LED registered.
    > i2c-core.o: client [HDD_LED] registered to adapter [SMBus CSB6 adapter
    > at 0580](pos. 0).
    > Qhwif: qinfo proc entries installed OK
    > Qhwif: Qhwif driver successfully loaded as typhoon driver
    > LEDdrv: LED driver successfully loaded as Typhoon driver
    > Linux NET4.0 for Linux 2.4
    > Based upon Swansea University Computer Society NET3.039
    > Initializing RT netlink socket
    > Starting kswapd
    > VFS: Disk quotas vdquot_6.5.1
    > Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    > SGI XFS 1.2pre4 with ACLs, quota, no debug enabled
    > xnvram: v 2.2 initializing platform ID=402002
    > xnvram: installed OK
    > Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
    > SERIAL_PCI enabled
    > ttyS00 at 0x03f8 (irq = 4) is a 16550A
    > Non-volatile memory driver v1.1
    > QuantaWDT driver registered I/O region 420<6>Uniform Multi-Platform
    > E-IDE driver Revision: 6.31
    > ide: Assuming 33MHz system bus speed for PIO modes; override with
    > idebus=xx
    > CMD680: IDE controller on PCI bus 00 dev 28
    > CMD680: chipset revision 2
    > CMD680: 100% native mode on irq 11
    > ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hdaio, hdbio
    > ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdcio, hddio
    > ServerWorks CSB6: IDE controller on PCI bus 00 dev 79
    > ServerWorks CSB6: chipset revision 160
    > ServerWorks CSB6: not 100% native mode: will probe irqs later
    > ide2: BM-DMA at 0xffa0-0xffa7, BIOS settings: hdeMA, hdfio
    > ide3: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdgMA, hdhio
    > hda: Maxtor 7Y250P0, ATA DISK drive
    > hdc: Maxtor 7Y250P0, ATA DISK drive
    > hde: Maxtor 7Y250P0, ATA DISK drive
    > hdg: Maxtor 7Y250P0, ATA DISK drive
    > ide0 at 0xc400-0xc407,0xc002 on irq 11
    > ide1 at 0xb800-0xb807,0xb402 on irq 11
    > ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
    > ide3 at 0x170-0x177,0x376 on irq 15
    > hda: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    > UDMA(100)
    > hdc: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    > UDMA(100)
    > hde: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    > UDMA(100)
    > hdg: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63,
    > UDMA(100)
    > Partition check:
    > hda: hda1 hda2 hda3 < hda5 hda6 > hda4
    > hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 > hdc4
    > hde: hde1 hde2 hde3 < hde5 hde6 > hde4
    > hdg: hdg1 hdg2 hdg3 < hdg5 hdg6 > hdg4
    > RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    > loop: loaded (max 8 devices)
    > md: linear personality registered as nr 1
    > md: raid0 personality registered as nr 2
    > md: raid1 personality registered as nr 3
    > md: raid5 personality registered as nr 4
    > raid5: measuring checksumming speed
    > 8regs : 2363.200 MB/sec
    > 32regs : 1563.200 MB/sec
    > pIII_sse : 3095.600 MB/sec
    > pII_mmx : 2847.600 MB/sec
    > p5_mmx : 2796.800 MB/sec
    > raid5: using function: pIII_sse (3095.600 MB/sec)
    > md: spare personality registered as nr 8
    > md: md driver 0.91.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    > md: Autodetecting RAID arrays.
    > md: autorun ...
    > md: ... autorun DONE.
    > LVM version 1.0.6(25/10/2002)
    > NET4: Linux TCP/IP 1.0 for NET4.0
    > IP Protocols: ICMP, UDP, TCP, IGMP
    > IP: routing cache hash table of 4096 buckets, 32Kbytes
    > TCP: Hash tables configured (established 32768 bind 32768)
    > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    > NET4: Linux IPX 0.47 for NET4.0
    > IPX Portions Copyright (c) 1995 Caldera, Inc.
    > IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
    > NET4: AppleTalk 0.18a for Linux NET4.0
    > RAMDISK: Compressed image found at block 0
    > Freeing initrd memory: 2734k freed
    > EXT2-fs warning: checktime reached, running e2fsck is recommended
    > VFS: Mounted root (ext2 filesystem).
    > Freeing unused kernel memory: 72k freed
    > init_guardianflash_mtd: Found Quanta Platform
    > Guardian.0: Found 1 x 512KiB AMD AM29F004BT at 0x0
    > SCSI subsystem driver Revision: 1.00
    > sym.0.3.1: setting PCI_COMMAND_PARITY...
    > sym.0.3.0: setting PCI_COMMAND_PARITY...
    > sym0: <896> rev 0x7 on pci bus 0 device 3 function 1 irq 3
    > sym0: using 64 bit DMA addressing
    > sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
    > sym0: open drain IRQ line driver, using on-chip SRAM
    > sym0: using LOAD/STORE-based firmware.
    > sym0: handling phase mismatch from SCRIPTS.
    > sym0: SCSI BUS has been reset.
    > sym1: <896> rev 0x7 on pci bus 0 device 3 function 0 irq 7
    > sym1: using 64 bit DMA addressing
    > sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
    > sym1: open drain IRQ line driver, using on-chip SRAM
    > sym1: using LOAD/STORE-based firmware.
    > sym1: handling phase mismatch from SCRIPTS.
    > sym1: SCSI BUS has been reset.
    > scsi0 : sym-2.1.17a
    > scsi1 : sym-2.1.17a
    > i2c-core.o: driver Qhwmon registered.
    > i2c-core.o: client [Qhwmon] registered to adapter [SMBus CSB6 adapter
    > at 0580](pos. 1).
    > Qhwmon: proc entries installed OK
    > Qhwmon: ExpUnit setup skipped!
    > Qhwmon: Hardware monitor driver successfully loaded as Typhoon driver
    > Qinfo: i2c driver attached, getting eeprom image
    > Qinfo: E1 csum = E2 csum and both good
    > Qinfo: eeprom image received.
    > Qinfo: Reading from EEPROM... CheckSum = 0000
    > Qinfo:0000: 00 c0 b6 06 3e c0 00 00 00 00 01 02 01 47 00 00
    > ....>........G..
    > Qinfo:0010: ff ff ff ff 01 40 ed fe 0d f0 02 70 6f 70 00 00
    > .....@.....pop..
    > Qinfo:0020: 00 00 00 00 00 00 00 00 00 00 00 ac 15 02 6a ff
    > ..............j.
    > Qinfo:0030: ff 00 00 ac 15 01 37 ac 13 01 53 ac 15 02 01 ac
    > ......7...S.....
    > Qinfo:0040: 15 02 01 00 ac 15 0a 06 ff ff 00 00 ac 15 01 37
    > ...............7
    > Qinfo:0050: ac 15 02 01 ac 15 02 01 01 4f 50 23 42 ef fb 22
    > .........OP#B.."
    > Qinfo:0060: 42 37 3b 23 42 01 01 02 00 ff 00 00 00 00 00 00
    > B7;#B...........
    > Qinfo:0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f2 fe
    > ................
    > Qinfo: Bios Version: :S18Q3B01:
    > [events: 0000006f]
    > md: bind
    > [events: 0000006f]
    > md: bind
    > [events: 0000006f]
    > md: bind
    > [events: 0000006f]
    > md: bind
    > md: hda2's event counter: 0000006f
    > md: hde2's event counter: 0000006f
    > md: hdg2's event counter: 0000006f
    > md: hdc2's event counter: 0000006f
    > md: md100: raid array is not clean -- starting background
    > reconstruction
    > md: RAID level 1 does not need chunksize! Continuing anyway.
    > md100: max total readahead window set to 124k
    > md100: 1 data-disks, max readahead per data-disk: 124k
    > raid1: device hda2 operational as mirror 0
    > raid1: device hde2 operational as mirror 3
    > raid1: device hdg2 operational as mirror 2
    > raid1: device hdc2 operational as mirror 1
    > raid1: raid set md100 not clean; reconstructing mirrors
    > raid1: raid set md100 active with 4 out of 4 mirrors
    > md: updating md100 RAID superblock on device
    > md: hda2 [events: 00000070]<6>(write) hda2's sb offset: 546112
    > md: syncing RAID array md100
    > md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
    > md: using maximum available idle IO bandwith (but not more than 100000
    > KB/sec) for reconstruction.
    > md: using 124k window, over a total of 546112 blocks.
    > md: hde2 [events: 00000070]<6>(write) hde2's sb offset: 546112
    > md: hdg2 [events: 00000070]<6>(write) hdg2's sb offset: 546112
    > md: hdc2 [events: 00000070]<6>(write) hdc2's sb offset: 546112
    > [events: 00000071]
    > md: bind
    > [events: 00000071]
    > md: bind
    > [events: 00000071]
    > md: bind
    > [events: 00000071]
    > md: bind
    > md: hda5's event counter: 00000071
    > md: hdc5's event counter: 00000071
    > md: hde5's event counter: 00000071
    > md: hdg5's event counter: 00000071
    > md: md101: raid array is not clean -- starting background
    > reconstruction
    > md: RAID level 1 does not need chunksize! Continuing anyway.
    > md101: max total readahead window set to 124k
    > md101: 1 data-disks, max readahead per data-disk: 124k
    > raid1: device hda5 operational as mirror 0
    > raid1: device hdc5 operational as mirror 3
    > raid1: device hde5 operational as mirror 2
    > raid1: device hdg5 operational as mirror 1
    > raid1: raid set md101 not clean; reconstructing mirrors
    > raid1: raid set md101 active with 4 out of 4 mirrors
    > md: updating md101 RAID superblock on device
    > md: hda5 [events: 00000072]<6>(write) hda5's sb offset: 273024
    > md: delaying resync of md101 until md100 has finished resync (they
    > share one or more physical units)
    > md: hdc5 [events: 00000072]<6>(write) hdc5's sb offset: 273024
    > md: hde5 [events: 00000072]<6>(write) hde5's sb offset: 273024
    > md: hdg5 [events: 00000072]<6>(write) hdg5's sb offset: 273024
    > XFS mounting filesystem md(9,100)
    > Starting XFS recovery on filesystem: md(9,100) (dev: 9/100)
    > Ending XFS recovery on filesystem: md(9,100) (dev: 9/100)
    >
    > SnapNIC: found MAC 0xc0b6063ec1
    > ,<5>
    > SnapNIC: found MAC 0xc0b6063ec0
    > ,<5>SnapNIC: Found all NICs (2)
    > SnapNIC: Register 2 NIC devices sorted by MAC
    > Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension
    > (NICE) ver. 7.0.0 (08/14/03)
    > eth0: Broadcom BCM5704 1000Base-T found at mem febd0000, IRQ 5, node
    > addr 00c0b6063ec0
    > eth0: Broadcom BCM5704 Integrated Copper transceiver found
    > eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
    > 802.1Q VLAN ON
    > eth1: Broadcom BCM5704 1000Base-T found at mem febf0000, IRQ 9, node
    > addr 00c0b6063ec1
    > eth1: Broadcom BCM5704 Integrated Copper transceiver found
    > eth1: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
    > 802.1Q VLAN ON
    > xnvram: CMOS is currently locked.
    > Qinfo: valid key presented - eeprom unlocked
    > Qinfo: Key 0 - Locking eeprom
    > Qhwif: Enable watchdog management- 30 min timeout
    > bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit
    > flow control ON
    > xnvram: i=0 bcount[0]=5
    > xnvram: i=0 bcount[0]=5
    > md: md100: sync done.
    > md: syncing RAID array md101
    > md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
    > md: using maximum available idle IO bandwith (but not more than 100000
    > KB/sec) for reconstruction.
    > md: using 124k window, over a total of 273024 blocks.
    > md: md101: sync done.
    >
    >




+ Reply to Thread