D-Link DGE-528T; Which driver? 2:nd try... - Solaris

This is a discussion on D-Link DGE-528T; Which driver? 2:nd try... - Solaris ; A second try: I have added a D-Link DGE-528T on my PC but I can't figure out if there is any valid driver I can use. I run a AMD Athlon on a VIA K8M800 motherboard with Nevada_b27, and the ...

+ Reply to Thread
Results 1 to 2 of 2

Thread: D-Link DGE-528T; Which driver? 2:nd try...

  1. D-Link DGE-528T; Which driver? 2:nd try...

    A second try: I have added a D-Link DGE-528T on my PC but I can't
    figure out if there is any
    valid driver I can use. I run a AMD Athlon on a VIA K8M800 motherboard
    with Nevada_b27,
    and the built in network comes right up as rtls0.

    I've tried the skge driver with no success. I did pkgrm SK98sol;
    rem_drv skge
    pkgadd SKGEsolx which said:

    Processing package instance from

    ## Installing package in global zone

    SysKonnect Gigabit Ethernet Adapter families 64 bit driver(i386)
    8.12.1.3
    SysKonnect GmbH

    ----------------------
    IP configuration
    ----------------------

    Do you want to configure the IP interfaces now (y/n)? n
    Using as the package base directory.
    ## Processing package information.
    ## Processing system information.
    10 package pathnames are already properly installed.
    ## Verifying disk space requirements.
    ## Checking for conflicts with packages already installed.
    ## Checking for setuid/setgid programs.

    This package contains scripts which will be executed with super-user
    permission during the process of installing this package.

    Do you want to continue with the installation of [y,n,?] y

    Installing SysKonnect Gigabit Ethernet Adapter families 64 bit driver
    as

    ## Executing preinstall script.
    ## Installing part 1 of 1.
    /etc/rcS.d/S50skge
    /kernel/drv/amd64/skge
    /kernel/drv/skge.conf
    /usr/sbin/skge_vlan_config
    /usr/share/man/man7d/skge.7d
    [ verifying class ]
    [ verifying class ]
    ## Executing postinstall script.
    add_drv skge
    devfsadm: driver failed to attach: skge
    Warning: Driver (skge) successfully added to system but failed to
    attach
    SKGEsolx driver load failed!
    pkgadd: ERROR: postinstall script did not complete successfully

    Installation of partially failed.
    ## Interrupted: package not installed in any non-global
    zones

    1 package was not processed!

    /usr/X11/bin/scanpci -vsays

    pci bus 0x0000 cardnum 0x09 function 0x00: vendor 0x1186 device 0x4300
    D-Link System Inc DGE-528T Gigabit Ethernet Adapter
    STATUS 0x02b0 COMMAND 0x0007
    CLASS 0x02 0x00 0x00 REVISION 0x10
    BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x08
    BASE0 0x00009001 addr 0x00009000 I/O
    BASE1 0xeb000000 addr 0xeb000000 MEM
    MAX_LAT 0x40 MIN_GNT 0x20 INT_PIN 0x01 INT_LINE 0x05

    prtconf -pv says

    Node 0x00000c
    assigned-addresses:
    81004810.00000000.00009000.00000000.00000100.82004 814.00000000.eb000000.00000000.00000100.82004830.0 0000000.00000000.00000000.00020000
    reg:
    00004800.00000000.00000000.00000000.00000000.01004 810.00000000.00000000.00000000.00000100.02004814.0 0000000.00000000.00000000.00000100.02004830.000000 00.00000000.00000000.00020000
    compatible: 'pci1186,4300.1186.4300.10' +
    'pci1186,4300.1186.4300' + 'pci1186,4300' + 'pci1186,4300.10' +
    'pci1186,4300' + 'pciclass,020000' + 'pciclass,0200'
    model: 'Ethernet controller'
    power-consumption: 00000001.00000001
    66mhz-capable:
    fast-back-to-back:
    devsel-speed: 00000001
    interrupts: 00000001
    max-latency: 00000040
    min-grant: 00000020
    subsystem-vendor-id: 00001186
    subsystem-id: 00004300
    unit-address: '9'
    class-code: 00020000
    revision-id: 00000010
    vendor-id: 00001186
    device-id: 00004300
    name: 'pci1186,4300'


  2. Re: D-Link DGE-528T; Which driver? 2:nd try...

    Forget it. I figured out that the realtek gigabit driver i included in
    b27...
    I'm happy gigabitting now


+ Reply to Thread