Thanks for your reply.
Please find the output as follows,


$cat /etc/snmp/snmpd.conf'

################################################## ######################
#######
#
# snmpd.conf:
# An example configuration file for configuring the ucd-snmp snmpd
agent.
#
################################################## ######################
#######
#
# This file is intended to only be as a starting point. Many more
# configuration directives exist than are mentioned in this file. For
# full details, see the snmpd.conf(5) manual page.
#
# All lines beginning with a '#' are comments and are intended for you
# to read. All other lines are configuration commands for the agent.

################################################## ######################
#######
# Access Control
################################################## ######################
#######

# As shipped, the snmpd demon will only respond to queries on the
# system mib group until this file is replaced or modified for
# security purposes. Examples are shown below about how to increase the
# level of access.

# By far, the most common question I get about the agent is "why won't
# it work?", when really it should be "how do I configure the agent to
# allow me to access it?"
#
# By default, the agent responds to the "public" community for read
# only access, if run out of the box without any configuration file in
# place. The following examples show you other ways of configuring
# the agent so that you can change the community names, and give
# yourself write access to the mib tree as well.
#
# For more information, read the FAQ as well as the snmpd.conf(5)
# manual page.

####
# First, map the community name "public" into a "security name"

# sec.name source community
com2sec notConfigUser default public

####
# Second, map the security name into a group name:

# groupName securityModel securityName
group notConfigGroup v1 notConfigUser
group notConfigGroup v2c notConfigUser

####
# Third, create a view for us to let the group have rights to:

# Make at least snmpwalk -v 1 localhost -c public system fast again.
# name incl/excl subtree mask(optional)
view systemview included .1.3.6.1.2.1.1
view systemview included .1.3.6.1.2.1.25.1.1

####
# Finally, grant the group read-only access to the systemview view.
# group context sec.model sec.level prefix read write
notif
access notConfigGroup "" any noauth exact systemview
none none

#
------------------------------------------------------------------------
-----

# Here is a commented out example configuration that allows less
# restrictive access.

# YOU SHOULD CHANGE THE "COMMUNITY" TOKEN BELOW TO A NEW KEYWORD ONLY
# KNOWN AT YOUR SITE. YOU *MUST* CHANGE THE NETWORK TOKEN BELOW TO
# SOMETHING REFLECTING YOUR LOCAL NETWORK ADDRESS SPACE.

## sec.name source community
#com2sec local localhost COMMUNITY
#com2sec mynetwork NETWORK/24 COMMUNITY

## group.name sec.model sec.name
#group MyRWGroup any local
#group MyROGroup any mynetwork
#
#group MyRWGroup any otherv3user
#...

## incl/excl subtree mask
#view all included .1 80

## -or just the mib2 tree-

#view mib2 included .iso.org.dod.internet.mgmt.mib-2 fc


## context sec.model sec.level prefix read write notif
#access MyROGroup "" any noauth 0 all none none
#access MyRWGroup "" any noauth 0 all all all


################################################## ######################
#######
# Sample configuration to make net-snmpd RFC 1213.
# Unfortunately v1 and v2c don't allow any user based authentification,
so
# opening up the default config is not an option from a security point.
#
# WARNING: If you uncomment the following lines you allow write access
to your
# snmpd daemon from any source! To avoid this use different names for
your
# community or split out the write access to a different community and
# restrict it to your local network.
# Also remember to comment the syslocation and syscontact parameters
later as
# otherwise they are still read only (see FAQ for net-snmp).
#

# First, map the community name "public" into a "security name"
# sec.name source community
#com2sec notConfigUser default public

# Second, map the security name into a group name:
# groupName securityModel securityName
#group notConfigGroup v1 notConfigUser
#group notConfigGroup v2c notConfigUser
# Third, create a view for us to let the group have rights to:
# Open up the whole tree for ro, make the RFC 1213 required ones rw.
# name incl/excl subtree mask(optional)
#view roview included .1
#view rwview included system.sysContact
#view rwview included system.sysName
#view rwview included system.sysLocation
#view rwview included
interfaces.ifTable.ifEntry.ifAdminStatus
#view rwview included
at.atTable.atEntry.atPhysAddress
#view rwview included at.atTable.atEntry.atNetAddress
#view rwview included ip.ipForwarding
#view rwview included ip.ipDefaultTTL
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteDest
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteIfIndex
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteMetric1
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteMetric2
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteMetric3
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteMetric4
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteType
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteAge
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteMask
#view rwview included
ip.ipRouteTable.ipRouteEntry.ipRouteMetric5
#view rwview included
ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMedi aIfIndex
#view rwview included
ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMedi aPhysAddress
#view rwview included
ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMedi aNetAddress
#view rwview included
ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMedi aType
#view rwview included
tcp.tcpConnTable.tcpConnEntry.tcpConnState
#view rwview included
egp.egpNeighTable.egpNeighEntry.egpNeighEventTrigg er
#view rwview included snmp.snmpEnableAuthenTraps

# Finally, grant the group read-only access to the systemview view.
# group context sec.model sec.level prefix read write
notif
#access notConfigGroup "" any noauth exact roview rwview
none



################################################## ######################
#######
# System contact information
#

# It is also possible to set the sysContact and sysLocation system
# variables through the snmpd.conf file:

syslocation Unknown (edit /etc/snmp/snmpd.conf)
syscontact Root (configure /etc/snmp/snmp.local.conf)

# Example output of snmpwalk:
# % snmpwalk -v 1 localhost -c public system
# system.sysDescr.0 = "SunOS name sun4c"
# system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4
# system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55
# system.sysContact.0 = "Me "
# system.sysName.0 = "name"
# system.sysLocation.0 = "Right here, right now."
# system.sysServices.0 = 72
#
------------------------------------------------------------------------
-----


################################################## ######################
#######
# Process checks.
#
# The following are examples of how to use the agent to check for
# processes running on the host. The syntax looks something like:
#
# proc NAME [MAX=0] [MIN=0]
#
# NAME: the name of the process to check for. It must match
# exactly (ie, http will not find httpd processes).
# MAX: the maximum number allowed to be running. Defaults to 0.
# MIN: the minimum number to be running. Defaults to 0.

#
# Examples (commented out by default):
#

# Make sure mountd is running
#proc mountd

# Make sure there are no more than 4 ntalkds running, but 0 is ok too.
#proc ntalkd 4

# Make sure at least one sendmail, but less than or equal to 10 are
running.
#proc sendmail 10 1

# A snmpwalk of the process mib tree would look something like this:
#
# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.2
# enterprises.ucdavis.procTable.prEntry.prIndex.1 = 1
# enterprises.ucdavis.procTable.prEntry.prIndex.2 = 2
# enterprises.ucdavis.procTable.prEntry.prIndex.3 = 3
# enterprises.ucdavis.procTable.prEntry.prNames.1 = "mountd"
# enterprises.ucdavis.procTable.prEntry.prNames.2 = "ntalkd"
# enterprises.ucdavis.procTable.prEntry.prNames.3 = "sendmail"
# enterprises.ucdavis.procTable.prEntry.prMin.1 = 0
# enterprises.ucdavis.procTable.prEntry.prMin.2 = 0
# enterprises.ucdavis.procTable.prEntry.prMin.3 = 1
# enterprises.ucdavis.procTable.prEntry.prMax.1 = 0
# enterprises.ucdavis.procTable.prEntry.prMax.2 = 4
# enterprises.ucdavis.procTable.prEntry.prMax.3 = 10
# enterprises.ucdavis.procTable.prEntry.prCount.1 = 0
# enterprises.ucdavis.procTable.prEntry.prCount.2 = 0
# enterprises.ucdavis.procTable.prEntry.prCount.3 = 1
# enterprises.ucdavis.procTable.prEntry.prErrorFlag. 1 = 1
# enterprises.ucdavis.procTable.prEntry.prErrorFlag. 2 = 0
# enterprises.ucdavis.procTable.prEntry.prErrorFlag. 3 = 0
# enterprises.ucdavis.procTable.prEntry.prErrMessage .1 = "No mountd
process running."
# enterprises.ucdavis.procTable.prEntry.prErrMessage .2 = ""
# enterprises.ucdavis.procTable.prEntry.prErrMessage .3 = ""
# enterprises.ucdavis.procTable.prEntry.prErrFix.1 = 0
# enterprises.ucdavis.procTable.prEntry.prErrFix.2 = 0
#
# Note that the errorFlag for mountd is set to 1 because one is not
# running (in this case an rpc.mountd is, but thats not good enough),
# and the ErrMessage tells you what's wrong. The configuration
# imposed in the snmpd.conf file is also shown.
#
# Special Case: When the min and max numbers are both 0, it assumes
# you want a max of infinity and a min of 1.
#


#
------------------------------------------------------------------------
-----


################################################## ######################
#######
# Executables/scripts
#

#
# You can also have programs run by the agent that return a single
# line of output and an exit code. Here are two examples.
#
# exec NAME PROGRAM [ARGS ...]
#
# NAME: A generic name.
# PROGRAM: The program to run. Include the path!
# ARGS: optional arguments to be passed to the program

# a simple hello world

#exec echotest /bin/echo hello world

# Run a shell script containing:
#
# #!/bin/sh
# echo hello world
# echo hi there
# exit 35
#
# Note: this has been specifically commented out to prevent
# accidental security holes due to someone else on your system writing
# a /tmp/shtest before you do. Uncomment to use it.
#
#exec shelltest /bin/sh /tmp/shtest

# Then,
# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.8
# enterprises.ucdavis.extTable.extEntry.extIndex.1 = 1
# enterprises.ucdavis.extTable.extEntry.extIndex.2 = 2
# enterprises.ucdavis.extTable.extEntry.extNames.1 = "echotest"
# enterprises.ucdavis.extTable.extEntry.extNames.2 = "shelltest"
# enterprises.ucdavis.extTable.extEntry.extCommand.1 = "/bin/echo hello
world"
# enterprises.ucdavis.extTable.extEntry.extCommand.2 = "/bin/sh
/tmp/shtest"
# enterprises.ucdavis.extTable.extEntry.extResult.1 = 0
# enterprises.ucdavis.extTable.extEntry.extResult.2 = 35
# enterprises.ucdavis.extTable.extEntry.extOutput.1 = "hello world."
# enterprises.ucdavis.extTable.extEntry.extOutput.2 = "hello world."
# enterprises.ucdavis.extTable.extEntry.extErrFix.1 = 0
# enterprises.ucdavis.extTable.extEntry.extErrFix.2 = 0

# Note that the second line of the /tmp/shtest shell script is cut
# off. Also note that the exit status of 35 was returned.

#
------------------------------------------------------------------------
-----


################################################## ######################
#######
# disk checks
#

# The agent can check the amount of available disk space, and make
# sure it is above a set limit.

# disk PATH [MIN=100000]
#
# PATH: mount path to the disk in question.
# MIN: Disks with space below this value will have the Mib's errorFlag
set.
# Default value = 100000.

# Check the / partition and make sure it contains at least 10 megs.

#disk / 10000

# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.9
# enterprises.ucdavis.diskTable.dskEntry.diskIndex.1 = 0
# enterprises.ucdavis.diskTable.dskEntry.diskPath.1 = "/" Hex: 2F
# enterprises.ucdavis.diskTable.dskEntry.diskDevice. 1 =
"/dev/dsk/c201d6s0"
# enterprises.ucdavis.diskTable.dskEntry.diskMinimum .1 = 10000
# enterprises.ucdavis.diskTable.dskEntry.diskTotal.1 = 837130
# enterprises.ucdavis.diskTable.dskEntry.diskAvail.1 = 316325
# enterprises.ucdavis.diskTable.dskEntry.diskUsed.1 = 437092
# enterprises.ucdavis.diskTable.dskEntry.diskPercent .1 = 58
# enterprises.ucdavis.diskTable.dskEntry.diskErrorFl ag.1 = 0
# enterprises.ucdavis.diskTable.dskEntry.diskErrorMs g.1 = ""

#
------------------------------------------------------------------------
-----


################################################## ######################
#######
# load average checks
#

# load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0]
#
# 1MAX: If the 1 minute load average is above this limit at query
# time, the errorFlag will be set.
# 5MAX: Similar, but for 5 min average.
# 15MAX: Similar, but for 15 min average.

# Check for loads:
#load 12 14 14

# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.10
# enterprises.ucdavis.loadTable.laEntry.loadaveIndex .1 = 1
# enterprises.ucdavis.loadTable.laEntry.loadaveIndex .2 = 2
# enterprises.ucdavis.loadTable.laEntry.loadaveIndex .3 = 3
# enterprises.ucdavis.loadTable.laEntry.loadaveNames .1 = "Load-1"
# enterprises.ucdavis.loadTable.laEntry.loadaveNames .2 = "Load-5"
# enterprises.ucdavis.loadTable.laEntry.loadaveNames .3 = "Load-15"
# enterprises.ucdavis.loadTable.laEntry.loadaveLoad. 1 = "0.49" Hex: 30
2E 34 39
# enterprises.ucdavis.loadTable.laEntry.loadaveLoad. 2 = "0.31" Hex: 30
2E 33 31
# enterprises.ucdavis.loadTable.laEntry.loadaveLoad. 3 = "0.26" Hex: 30
2E 32 36
# enterprises.ucdavis.loadTable.laEntry.loadaveConfi g.1 = "12.00"
# enterprises.ucdavis.loadTable.laEntry.loadaveConfi g.2 = "14.00"
# enterprises.ucdavis.loadTable.laEntry.loadaveConfi g.3 = "14.00"
# enterprises.ucdavis.loadTable.laEntry.loadaveError Flag.1 = 0
# enterprises.ucdavis.loadTable.laEntry.loadaveError Flag.2 = 0
# enterprises.ucdavis.loadTable.laEntry.loadaveError Flag.3 = 0
# enterprises.ucdavis.loadTable.laEntry.loadaveErrMe ssage.1 = ""
# enterprises.ucdavis.loadTable.laEntry.loadaveErrMe ssage.2 = ""
# enterprises.ucdavis.loadTable.laEntry.loadaveErrMe ssage.3 = ""

#
------------------------------------------------------------------------
-----


################################################## ######################
#######
# Extensible sections.
#

# This alleviates the multiple line output problem found in the
# previous executable mib by placing each mib in its own mib table:

# Run a shell script containing:
#
# #!/bin/sh
# echo hello world
# echo hi there
# exit 35
#
# Note: this has been specifically commented out to prevent
# accidental security holes due to someone else on your system writing
# a /tmp/shtest before you do. Uncomment to use it.
#
# exec .1.3.6.1.4.1.2021.50 shelltest /bin/sh /tmp/shtest

# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.50
# enterprises.ucdavis.50.1.1 = 1
# enterprises.ucdavis.50.2.1 = "shelltest"
# enterprises.ucdavis.50.3.1 = "/bin/sh /tmp/shtest"
# enterprises.ucdavis.50.100.1 = 35
# enterprises.ucdavis.50.101.1 = "hello world."
# enterprises.ucdavis.50.101.2 = "hi there."
# enterprises.ucdavis.50.102.1 = 0

# Now the Output has grown to two lines, and we can see the 'hi
# there.' output as the second line from our shell script.
#
# Note that you must alter the mib.txt file to be correct if you want
# the .50.* outputs above to change to reasonable text descriptions.

# Other ideas:
#
# exec .1.3.6.1.4.1.2021.51 ps /bin/ps
# exec .1.3.6.1.4.1.2021.52 top /usr/local/bin/top
# exec .1.3.6.1.4.1.2021.53 mailq /usr/bin/mailq

#
------------------------------------------------------------------------
-----


################################################## ######################
#######
# Pass through control.
#

# Usage:
# pass MIBOID EXEC-COMMAND
#
# This will pass total control of the mib underneath the MIBOID
# portion of the mib to the EXEC-COMMAND.
#
# Note: You'll have to change the path of the passtest script to your
# source directory or install it in the given location.
#
# Example: (see the script for details)
# (commented out here since it requires that you place the
# script in the right location. (its not installed by
default))

# pass .1.3.6.1.4.1.2021.255 /bin/sh /usr/local/local/passtest

# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.255
# enterprises.ucdavis.255.1 = "life the universe and everything"
# enterprises.ucdavis.255.2.1 = 42
# enterprises.ucdavis.255.2.2 = OID: 42.42.42
# enterprises.ucdavis.255.3 = Timeticks: (363136200) 42 days, 0:42:42
# enterprises.ucdavis.255.4 = IpAddress: 127.0.0.1
# enterprises.ucdavis.255.5 = 42
# enterprises.ucdavis.255.6 = Gauge: 42
#
# % snmpget -v 1 localhost public .1.3.6.1.4.1.2021.255.5
# enterprises.ucdavis.255.5 = 42
#
# % snmpset -v 1 localhost public .1.3.6.1.4.1.2021.255.1 s "New string"
# enterprises.ucdavis.255.1 = "New string"
#

# For specific usage information, see the man/snmpd.conf.5 manual page
# as well as the local/passtest script used in the above example.

# Added for support of bcm5820 cards.
pass .1.3.6.1.4.1.4413.4.1 /usr/bin/ucd5820stat

################################################## ######################
#######
# Further Information
#
# See the snmpd.conf manual page, and the output of "snmpd -H".

rocommunity public




Thanks & Regards,
ElayaRaja
__________________________________________________ _______________

-----Original Message-----
From: dave.shield@googlemail.com [mailto:dave.shield@googlemail.com] On
Behalf Of Dave Shield
Sent: Thursday, May 08, 2008 2:36 PM
To: Sathasivam, Elayaraja
Cc: Net-snmp-users@lists.sourceforge.net
Subject: Re: End of MIB

2008/5/8 Sathasivam, Elayaraja :
> Please note I am not using two different version.


Not two versions of the software
Two versions of SNMP requests.

The working command used SNMPv2c,
the failing one used SNMPv1.

It was never likely that this would be relevant, but it was worth
checking.


> 1)$snmpgetnext -v 1 -c public localhost system
> SNMPv2-MIB::sysDescr.0 = ....
> 2)$snmpgetnext -v 1 -c public localhost sysORUpTime.8
> HOST-RESOURCES-MIB::hrSystemUptime.0 = ....
> 3)$snmpgetnext -v 1 -c public localhost versiontag
> Error in packet.
> Reason: (noSuchName) There is no such variable name in this MIB.
> Failed object: UCD-SNMP-MIB::versionTag


Yup - that's pretty much what I expected.

This is definitely an access control problem.


> 6) Any thing I need to update the following file ?
> $ cat /etc/cups/snmp.conf
> #Address @LOCAL
> #Community public
> #DebugLevel 0
> #HostNameLookups off


Nope. That file is not relevant here.

What is the output from 'cat /etc/snmp/snmpd.conf' ?

Dave

-------------------------------------------------------------------------
This SF.net email is sponsored by the 2008 JavaOne(SM) Conference
Don't miss this year's exciting event. There's still time to save $100.
Use priority code J8TL2D2.
http://ad.doubleclick.net/clk;198757...un.com/javaone
_______________________________________________
Net-snmp-users mailing list
Net-snmp-users@lists.sourceforge.net
Please see the following page to unsubscribe or change other options:
https://lists.sourceforge.net/lists/...net-snmp-users