USB not working after reboot? Why? - Questions

This is a discussion on USB not working after reboot? Why? - Questions ; I rebooted the box. (Slackware 9.1) and now the Zire 21 with J-Pilot will not sync. No error. It just hangs. I know the pilot-link is working because I can do a pilot-xfer -help and get a a response. Below ...

+ Reply to Thread
Results 1 to 2 of 2

Thread: USB not working after reboot? Why?

  1. USB not working after reboot? Why?

    I rebooted the box. (Slackware 9.1) and now the Zire 21 with J-Pilot will
    not sync. No error. It just hangs.

    I know the pilot-link is working because I can do a pilot-xfer -help and get
    a a response.

    Below is the dmesg stuff. What is all the gibberish at the bottom. It seems
    to say that my USP device is not working?

    It was working fine before I rebooted.

    Oh, one other thing. Kpilot will not run at all. It's icon spins in the task
    bar and it goes away after about 15 seconds. I can't bring it up via a
    command line either.

    Any help would be appreciated.

    Al

    usbserial.c: USB Serial support registered for Handspring Visor / Treo /
    Palm 4.0 / Clié 4.x
    usbserial.c: Handspring Visor / Treo / Palm 4.0 / Clié 4.x converter
    detected
    usbserial.c: Handspring Visor / Treo / Palm 4.0 / Clié 4.x converter now
    attached to ttyUSB0 (or usb/tts/0 for devfs)
    usbserial.c: Handspring Visor / Treo / Palm 4.0 / Clié 4.x converter now
    attached to ttyUSB1 (or usb/tts/1 for devfs)
    usbserial.c: USB Serial support registered for Sony Clié 3.5
    visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony Clié driver v1.7
    uhci.c: e400: host controller halted. very bad
    usb.c: USB disconnect on device 00:1d.2-2 address 2
    visor.c: Bytes In = 307**Bytes*Out*=*326
    Unable to handle kernel NULL pointer dereference at virtual address 00000998
    *printing*eip:
    f8bf8344
    *pde = 00000000
    Oops: 0002
    CPU:****0
    EIP:****0010:[]****Not*tainted
    EFLAGS: 00010246
    eax: 00000000***ebx:*f6b5386c***ecx:*00000000***edx:*00 000000
    esi: f6b53888***edi:*00000001***ebp:*f6b53800***esp:*f6 a9df40
    ds: 0018***es:*0018***ss:*0018
    Process khubd (pid: 175, stackpage=f6a9d000)
    Stack: f8bf9880 f8bf9860 ed8eb3c0 00000000 f8bad177 f2b60e00 f6b53800
    00000000
    *******f2b60e00*00000100*0000000a*f699f400*0000000 1*f8bafb4d*f699f510
    00000002
    *******ed0c6b00*f7cddf60*00000001*00000001*f7cddf6 0*f699f400*f8bafde5
    f7cddf60
    Call Trace:****[]*[]*[]*[]
    []
    **[]*[]*[]

    Code: c7 80 98 09 00 00 00 00 00 00 8d 4e 58 ff 43 74 0f 8e 1e 05
    *<6>CSLIP:*code*copyright*1989*Regents*of*the*Universi ty*of*California
    PPP generic driver version 2.4.2
    PPP BSD Compression module registered
    PPP Deflate Compression module registered
    al@darkstar:~$

  2. Re: USB not working after reboot? Why?

    Adams-Blake Co. wrote:

    > uhci.c: e400: host controller halted. very bad


    .... that's ^^^^^^^^^^^^ the entry that is NG. have you changed
    anything about the system to require a reboot?
    ..
    --
    /// Michael J. Tobler: motorcyclist, surfer, skydiver, \\\
    \\\ and author: "Inside Linux", "C++ HowTo", "C++ Unleashed" ///
    Of course there's no reason for it, it's just our policy.


+ Reply to Thread