Re-visit: Thinkpad 760el D-Link dfe-690-txd problems - Portable

This is a discussion on Re-visit: Thinkpad 760el D-Link dfe-690-txd problems - Portable ; Hi, Sorry about not getting back to the NG until now about this problem. I've recompiled my kernel without pcmcia subsystem. I'm now using the pcmcia-cs-3.2.8 DHINDS. The card gives me a low pitch beep on insertion and a high ...

+ Reply to Thread
Results 1 to 9 of 9

Thread: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

  1. Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    Hi,

    Sorry about not getting back to the NG until now about this problem.

    I've recompiled my kernel without pcmcia subsystem. I'm now using the
    pcmcia-cs-3.2.8 DHINDS.

    The card gives me a low pitch beep on insertion and a high beep on eject.
    The manfid is not correct, (0x1186, 0x1340) should be (0x149 ,0x0000) for
    this card.

    I'm not sure where and how to proceed at this time. I've re-read the
    pcmcia-how-to just to see if I missed something.

    I also noticed that;

    pcmcia_core 42336 0 [ds i82365]

    show that it is not being used. The pcmcia-how-to states it should show 3
    for used.

    Any help would be appreciated!

    Regards and Godspeed,
    Gary

    The magic is in the Magician not the wand!


    The information for the session follows;

    uname -a
    --cut--
    Linux loki 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005 i586 unknown
    unknown GNU/Linux
    --cut--

    cardctl config;
    --cut--
    Socket 0:
    Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
    interface type is "cardbus"
    function 0:
    Socket 1:
    not configured
    --cut--

    cardctl info;
    --cut--
    PRODID_1=""
    PRODID_2=""
    PRODID_3=""
    PRODID_4=""
    MANFID=0000,0000
    FUNCID=255
    PRODID_1=""
    PRODID_2=""
    PRODID_3=""
    PRODID_4=""
    MANFID=0000,0000
    FUNCID=255
    --cut--

    cardctl status;

    --cut--
    Socket 0:
    3.3V CardBus card
    function 0: [ready]
    Socket 1:
    no card
    --cut--

    cardctl ident;

    --cut--
    Socket 0:
    no product info available
    PCI id: 0x1186, 0x1340
    Socket 1:
    no product info available
    --cut--

    cat /proc/intrrupts
    --cut--
    CPU0
    0: 34825905 XT-PIC timer
    1: 9816 XT-PIC keyboard
    2: 0 XT-PIC cascade
    6: 68 XT-PIC floppy
    8: 1 XT-PIC rtc
    12: 8713 XT-PIC PS/2 Mouse
    14: 43239 XT-PIC ide0
    NMI: 0
    LOC: 0
    ERR: 0
    MIS: 0
    --cut--


    cat /proc/pci

    --cut--

    PCI devices found:
    Bus 0, device 0, function 0:
    Host bridge: Intel Corp. 430MX - 82437MX Mob. System Ctrlr (MTSC) &
    82438MX Data Path (MTDP) (rev 2).
    Master Capable. Latency=32.
    Bus 0, device 1, function 0:
    ISA bridge: Intel Corp. 82371FB PIIX ISA [Triton I] (rev 2).
    Bus 0, device 2, function 0:
    CardBus bridge: Texas Instruments PCI1130 (rev 4).
    Master Capable. Latency=168. Min Gnt=128.
    Non-prefetchable 32 bit memory at 0x10211000 [0x10211fff].
    Bus 0, device 2, function 1:
    CardBus bridge: Texas Instruments PCI1130 (#2) (rev 4).
    Master Capable. Latency=168. Min Gnt=192.
    Non-prefetchable 32 bit memory at 0x10210000 [0x10210fff].
    Bus 0, device 3, function 0:
    VGA compatible controller: Trident Microsystems TGUI 9320 (rev 227).
    IRQ 11.
    Non-prefetchable 32 bit memory at 0x8000000 [0x81fffff].
    Non-prefetchable 32 bit memory at 0x8200000 [0x820ffff].
    Bus 1, device 0, function 0:
    Ethernet controller: (rev 16).
    Master Capable. No bursts. Min Gnt=32.Max Lat=64.
    --cut--

    lsmod
    --cut--
    Module Size Used by Not tainted
    ds 7060 2
    i82365 42192 2
    pcmcia_core 42336 0 [ds i82365]
    ide-scsi 9200 0
    --cut--

    lspci

    --cut--
    pcilib: Cannot open /proc/pci/bus/01/00.0
    Unable to read 64 bytes of configuration space.00.00.0 Host bridge: Intel
    Corp.
    430MX - 82437MX Mob. System Ctrlr (MTSC) & 82438MX Data Path (MTDP) (rev 02)
    00:00.0 Host bridge: Intel Corp. 430MX - 82437MX Mob. System Ctrlr (MTSC) &
    82438MX Data Path (MTDP) (rev 02)
    00:01.0 ISA bridge: Intel Corp. 82371FB PIIX ISA [Triton I] (rev 02)
    00:02.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    00:02.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    00:03.0 VGA compatible controller: Trident Microsystems TGUI 9320 (rev e3)
    --cut--


    lspci -vv -H1

    --cut--
    00:00.0 Host bridge: Intel Corp. 430MX - 82437MX Mob. System Ctrlr (MTSC) &
    82438MX Data Path (MTDP) (rev 02)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32

    00:01.0 ISA bridge: Intel Corp. 82371FB PIIX ISA [Triton I] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0

    00:02.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 168, cache line size 08
    Interrupt: pin A routed to IRQ 255
    Region 0: Memory at 10211000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=01, subordinate=03, sec-latency=176
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite-
    16-bit legacy interface ports at 0001

    00:02.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 168, cache line size 08
    Interrupt: pin B routed to IRQ 255
    Region 0: Memory at 10210000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=04, subordinate=06, sec-latency=176
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
    16-bit legacy interface ports at 0001

    00:03.0 VGA compatible controller: Trident Microsystems TGUI 9320 (rev e3)
    (prog-if 00 [VGA])
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin A routed to IRQ 11
    Region 0: Memory at 08000000 (32-bit, non-prefetchable)
    Region 1: Memory at 08200000 (32-bit, non-prefetchable)

    01:00.0 Ethernet controller: D-Link System Inc DFE-690TXD CardBus PC Card
    (rev 10)
    Subsystem: D-Link System Inc DFE-690TXD CardBus PC Card
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin A routed to IRQ 255
    Region 0: I/O ports at [disabled]
    Region 1: Memory at (32-bit, non-prefetchable) [disabled]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    --cut--

    /etc/pcmcia/config

    --cut--

    #04-22-05 15:30 gws
    #this will set-up a DFE-690TXD

    device "8139too"
    class "network" module "cb_enabler", "8139too_cb"

    device "8139cp"
    class "network" module "cb_enabler", "8139cp_cb"

    device "tulip_cb"
    class "network" module "cb_enabler", "tulip_cb"

    #04-23-05 gws 22:50
    #from lapeyere suggestion
    #the cardbus version of the Realtek rtl8139b

    device "realtek" class "network"
    module "cb_enabler", "pci-scan", "cb_shim", "rtl8139"

    card "D-Link DFE-690TXD" manfid 0x149, 0x0000 bind "realtek"

    card "D-Link DFE-690TXD"
    version "D-Link", "DFE-690TXD", "PC CARD"
    manfid 0x0149, 0x0000
    bind "realtek"

    #save area

    #bind "8139too"
    #bind "tulip_cb"
    #manfid 0x1186, 0x1340
    #bind "8139cp"
    --cut--
    /etc/pcmcia/config.opts

    --cut--
    #
    # Local PCMCIA Configuration File
    #
    #----------------------------------------------------------------------
    #
    # System resources available for PCMCIA cards
    #
    # NOTE: these settings have no effect on resources assigned to a
    # CardBus bridge device itself; this file only affects resources
    # assigned to cards. Also, interrupt settings here will only affect
    # ISA bus interrupts assigned to 16-bit cards. PCI interrupts
    # generally can't be reconfigured.
    #
    # With the kernel PCMCIA subsystem, these settings also have no effect
    # at all on resources used for 32-bit CardBus cards. Those are set by
    # the PCI hotplug subsystem.
    #

    # These are the official ports to use from pcmcia-cs:

    include port 0x100-0x4ff, port 0x800-0x8ff, port 0xc00-0xcff

    # However, ports 0x810-0x81f hurt on some DELL machines and
    # ports 0x3b0-0x3df hurt on some FSC machines, so we use this port
    # list instead:
    #include port 0x100-0x3af, port 0x3e0-0x4ff, port 0x800-0x80f, port
    0x820-0x8ff, port 0xc00-0xcff

    #05-02-05-gws 11:15
    #include port 0x1000-0x10ff
    include port 0x1000-0x17ff

    #05-02-05 gws 11:15

    #include memory 0xc0000-0xfffff
    #include memory 0xa0000000-0xa0ffffff

    #05-02-05 gws 11:15
    include memory 0x4000000-0x4000fff
    include memory 0x4002000-0x40002fff
    include memory 0x60000000-0x60ffffff

    # High port numbers do not always work...
    # include port 0x1000-0x17ff

    # Extra port range for IBM Token Ring
    #include port 0xa00-0xaff

    # Resources we should not use, even if they appear to be available

    # First built-in serial port
    exclude irq 4
    # Second built-in serial port
    #exclude irq 3
    # First built-in parallel port
    exclude irq 7

    #----------------------------------------------------------------------

    # Examples of options for loadable modules

    # To fix sluggish network with IBM ethernet adapter...
    #module "pcnet_cs" opts "mem_speed=600"

    # Options for IBM Token Ring adapters
    #module "ibmtr_cs" opts "mmiobase=0xd0000 srambase=0xd4000"

    # Options for Raylink/WebGear driver: uncomment only one line...
    # These are the default settings for use with the WebGear Windows driver:
    module "ray_cs" opts "essid=NETWORK_NAME hop_dwell=128 beacon_period=256
    translate=0"
    # Generic ad-hoc network
    #module "ray_cs" opts "essid=ADHOC_ESSID hop_dwell=128 beacon_period=256
    translate=1"
    # Infrastructure network for older cards
    #module "ray_cs" opts "net_type=1 essid=ESSID1"
    # Infrastructure network for WebGear
    #module "ray_cs" opts "net_type=1 essid=ESSID1 translate=1 hop_dwell=128
    beacon_period=256"

    # Options for WaveLAN/IEEE driver (AccessPoint mode)...
    #module "wvlan_cs" opts "station_name=MY_PC"
    # Options for WaveLAN/IEEE driver (ad-hoc mode)...
    #module "wvlan_cs" opts "port_type=3 channel=1 station_name=MY_PC"

    # Options for Xircom Netwave driver...
    #module "netwave_cs" opts "domain=0x100 scramble_key=0x0"

    --cut--
    /etc/rc.d/rc.pcmcia

    --cut--

    #!/bin/sh

    # rc.pcmcia 1.46 2004/05/07 06:24:58 (David Hinds)
    #
    # This is designed to work in BSD as well as SysV init setups. See
    # the HOWTO for customization instructions.

    # Tags for Red Hat init configuration tools
    #
    # chkconfig: 2345 45 96
    # processname: cardmgr
    # pidfile: /var/run/cardmgr.pid
    # config: /etc/pcmcia/config
    # config: /etc/pcmcia/config.opts
    # description: PCMCIA support is usually to support things like ethernet \
    # and modems in laptops. It won't get started unless \
    # configured so it is safe to have it installed on machines \
    # that don't need it.

    # Exit if pcmcia-cs is not installed
    test -x /sbin/cardmgr || exit 0

    # Save option values passed in through the environment
    for N in PCMCIA PCIC PCIC_OPTS CORE_OPTS CARDMGR_OPTS SCHEME ; do
    V=`eval echo '$'$N` ; if [ "$V" ] ; then eval ENV_$N=\"$V\" ; fi
    done

    # Source PCMCIA configuration, if available
    if [ -f /etc/pcmcia.conf ] ; then
    # Debian startup option file
    . /etc/pcmcia.conf
    elif [ -f /etc/sysconfig/pcmcia ] ; then
    # Red Hat startup option file
    . /etc/sysconfig/pcmcia
    else
    # Slackware startup options go right here:
    # Should be either i82365 or tcic
    PCIC=i82365
    # Put socket driver timing parameters here
    PCIC_OPTS="irq_list=5,10 poll_interval=100"
    #05-02-05 gws 11:10 this will disable scan
    #"do_scan=0"
    #05-02-05 gws 11:10 this limits scan to list
    #"irq_list=5,7,9,10,11"
    #
    # Put pcmcia_core options here
    CORE_OPTS=
    # Put cardmgr options here
    CARDMGR_OPTS=
    # To set the PCMCIA scheme at startup...
    SCHEME=
    fi
    for N in PCMCIA PCIC PCIC_OPTS CORE_OPTS CARDMGR_OPTS SCHEME ; do
    V=`eval echo '$'ENV_$N` ; if [ "$V" ] ; then eval $N=\"$V\" ; fi
    done
    if [ "$PCMCIA" -a "$PCMCIA" != "yes" ] ; then exit 0 ; fi

    usage()
    {
    echo "Usage: $0 {start|stop|status|restart|reload}"
    }

    cleanup()
    {
    while read SN CLASS MOD INST DEV EXTRA ; do
    if [ "$SN" != "Socket" ] ; then
    /etc/pcmcia/$CLASS stop $DEV 2> /dev/null
    fi
    done
    }

    EXITCODE=1
    for x in "1" ; do

    if [ "$PCIC" = "" ] ; then
    echo "PCIC module not defined in startup options!"
    break
    fi

    if [ $# -lt 1 ] ; then usage ; break ; fi
    action=$1

    case "$action" in

    start)
    echo -n "Starting PCMCIA services: "

    if [ -d /var/lib/pcmcia ] ; then
    SC=/var/lib/pcmcia/scheme
    RUN=/var/lib/pcmcia
    else
    SC=/var/run/pcmcia-scheme
    RUN=/var/run
    fi
    if [ -L $SC -o ! -O $SC ] ; then rm -f $SC ; fi
    if [ ! -f $SC ] ; then umask 022 ; touch $SC ; fi
    if [ "$SCHEME" ] ; then umask 022 ; echo $SCHEME > $SC ; fi

    if ! grep -q pcmcia /proc/devices ; then
    if [ -d /lib/modules/preferred ] ; then
    PC=/lib/modules/preferred/pcmcia
    else
    PC=/lib/modules/`uname -r`/pcmcia
    fi
    KD=/lib/modules/`uname -r`/kernel/drivers/pcmcia
    if [ -x /sbin/modprobe ] ; then
    /sbin/modprobe pcmcia_core $CORE_OPTS || break
    /sbin/modprobe $PCIC $PCIC_OPTS >/dev/null 2>&1 ||
    (/sbin/modprobe yenta_socket >/dev/null 2>&1 &&
    echo "using yenta_socket instead of $PCIC") ||
    /sbin/modprobe $PCIC $PCIC_OPTS || break
    /sbin/modprobe ds || break
    elif [ -d $PC ] ; then
    /sbin/insmod $PC/pcmcia_core.o $CORE_OPTS
    /sbin/insmod $PC/$PCIC.o $PCIC_OPTS
    /sbin/insmod $PC/ds.o
    else
    echo "module directory $PC not found."
    break
    fi
    fi

    if [ -s /var/run/cardmgr.pid ] && \
    kill -0 `cat /var/run/cardmgr.pid` 2>/dev/null ; then
    echo "cardmgr is already running."
    else
    if [ -r $RUN/stab ] ; then
    cat $RUN/stab | cleanup
    fi
    /sbin/cardmgr $CARDMGR_OPTS
    fi

    echo "done."
    touch /var/lock/subsys/pcmcia 2>/dev/null
    EXITCODE=0
    ;;

    stop)
    echo -n "Shutting down PCMCIA services: "
    if [ -s /var/run/cardmgr.pid ] ; then
    PID=`cat /var/run/cardmgr.pid`
    kill $PID
    # Give cardmgr a few seconds to handle the signal
    for N in 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 ; do
    kill -0 $PID 2>/dev/null || break
    sleep 2
    done
    fi
    killall -q "CardBus Watcher"
    if grep -q "^ds " /proc/modules ; then
    /sbin/rmmod ds
    /sbin/rmmod $PCIC 2>/dev/null || \
    /sbin/rmmod yenta_socket 2>/dev/null
    /sbin/rmmod pcmcia_core
    fi
    echo "done."
    rm -f /var/lock/subsys/pcmcia
    EXITCODE=0
    ;;

    status)
    pid=`/sbin/pidof cardmgr`
    if [ "$pid" != "" ] ; then
    echo "cardmgr (pid $pid) is running..."
    EXITCODE=0
    else
    echo "cardmgr is stopped"
    EXITCODE=3
    fi
    ;;

    restart|reload)
    $0 stop
    $0 start
    EXITCODE=$?
    ;;

    *)
    usage
    ;;

    esac

    done

    # Only exit if we're in our own subshell
    case $0 in *rc.pcmcia) exit $EXITCODE ;; esac

    --cut--

    dmesg
    --cut--
    Linux version 2.4.29pentium (gs@willi) (gcc version 3.3.4) #1 Tue Apr 26
    18:12:22 CDT 2005
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 0000000004000000 (usable)
    BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
    64MB LOWMEM available.
    On node 0 totalpages: 16384
    zone(0): 4096 pages.
    zone(1): 12288 pages.
    zone(2): 0 pages.
    DMI not present.
    ACPI: Unable to locate RSDP
    Kernel command line: BOOT_IMAGE=Linux-2.4.29p ro root=303
    No local APIC present or hardware disabled
    Initializing CPU#0
    Detected 119.754 MHz processor.
    Console: colour VGA+ 80x25
    Calibrating delay loop... 238.38 BogoMIPS
    Memory: 61684k/65536k available (1686k kernel code, 3464k reserved, 615k
    data, 144k init, 0k highmem)
    Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
    Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
    Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Intel Pentium with F0 0F bug - workaround enabled.
    CPU: After generic, caps: 000001bf 00000000 00000000 00000000
    CPU: Common caps: 000001bf 00000000 00000000 00000000
    CPU: Intel Pentium 75 - 200 stepping 0c
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
    mtrr: detected mtrr type: none
    ACPI: Subsystem revision 20040326
    ACPI: Interpreter disabled.
    PCI: PCI BIOS revision 2.10 entry at 0xfd930, last bus=6
    PCI: Using configuration type 1
    PCI: Probing PCI hardware
    PCI: Probing PCI hardware (bus 00)
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    VFS: Disk quotas vdquot_6.5.1
    Journalled Block Device driver loaded
    pty: 512 Unix98 ptys configured
    Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
    SHARE_IRQ SERIAL_PCI enabled
    ttyS00 at 0x03f8 (irq = 4) is a 16550A
    Real Time Clock Driver v1.10f
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a National Semiconductor PC87306
    RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
    loop: loaded (max 8 devices)
    Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    PIIXa: IDE controller at PCI slot 00:01.0
    PIIXa: chipset revision 2
    PIIXa: not 100% native mode: will probe irqs later
    PIIXa: neither IDE port enabled (BIOS)
    hda: IBM-DMCA-21440, ATA DISK drive
    hdb: SANYO CRD-S58P, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    hda: attached ide-disk driver.
    hda: 2818368 sectors (1443 MB) w/96KiB Cache, CHS=699/64/63
    hdb: attached ide-cdrom driver.
    hdb: ATAPI 8X CD-ROM drive, 256kB Cache
    Uniform CD-ROM driver Revision: 3.12
    Partition check:
    hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
    SCSI subsystem driver Revision: 1.00
    kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
    kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
    kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: raid1 personality registered as nr 3
    md: raid5 personality registered as nr 4
    raid5: measuring checksumming speed
    8regs : 56.800 MB/sec
    32regs : 52.400 MB/sec
    raid5: using function: 8regs (56.800 MB/sec)
    md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    LVM version 1.0.8(17/11/2003)
    Initializing Cryptographic API
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 4096 bind 8192)
    Linux IP multicast router 0.06 plus PIM-SM
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    VFS: Mounted root (ext3 filesystem) readonly.
    Freeing unused kernel memory: 144k freed
    Adding Swap: 62492k swap-space (priority -1)
    EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
    scsi0 : SCSI host adapter emulation for IDE ATAPI devices
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,7,9,10 status change on irq 10
    parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
    lp0: using parport0 (polling).
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,7,9,10 status change on irq 10
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9,10 status change on irq 10
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9 polling interval = 1000 ms
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = none!<6> *NO* card interrupts, polling interval
    = 1000 ms
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,7,9,10 status change on irq 10
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,7,9,10 status change on irq 10
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9,10 status change on irq 10
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9,10 status change on irq 10
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9,10 status change on irq 10
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9,10 polling interval = 1000 ms
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,9,10 polling interval = 1000 ms
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: cb_free(bus 1)
    unloading PCMCIA Card Services
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,10 polling interval = 1000 ms
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: could not allocate 4K memory for CardBus socket 0
    EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
    EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0
    cs: could not allocate 4K memory for CardBus socket 0

    --cut--

    tail -100 /var/log/messages

    --cut--
    May 2 11:28:21 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 11:28:21 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 11:28:21 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 11:28:21 loki kernel: ISA irqs (scanned) = 5,9,10 status change
    on irq 10
    May 2 11:28:21 loki cardmgr[3114]: watching 2 sockets
    May 2 11:28:22 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 11:28:22 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 11:28:22 loki cardmgr[3115]: unsupported card in socket 0
    May 2 11:28:22 loki cardmgr[3115]: no product info available
    May 2 11:28:22 loki cardmgr[3115]: PCI id: 0x1186, 0x1340
    May 2 11:30:07 loki cardmgr[3115]: exiting
    May 2 11:30:09 loki kernel: cs: cb_free(bus 1)
    May 2 11:30:09 loki kernel: unloading PCMCIA Card Services
    May 2 11:30:10 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 2 11:30:10 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 2 11:30:10 loki kernel: options: [pci] [cardbus] [apm]
    May 2 11:30:10 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 2 11:30:10 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 11:30:10 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 11:30:10 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 11:30:10 loki kernel: ISA irqs (scanned) = 5,9,10 status change
    on irq 10
    May 2 11:30:10 loki cardmgr[3172]: watching 2 sockets
    May 2 11:30:11 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 11:30:11 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 11:30:11 loki cardmgr[3173]: unsupported card in socket 0
    May 2 11:30:11 loki cardmgr[3173]: no product info available
    May 2 11:30:11 loki cardmgr[3173]: PCI id: 0x1186, 0x1340
    May 2 11:32:31 loki cardmgr[3173]: exiting
    May 2 11:32:33 loki kernel: cs: cb_free(bus 1)
    May 2 11:32:33 loki kernel: unloading PCMCIA Card Services
    May 2 11:32:33 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 2 11:32:33 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 2 11:32:33 loki kernel: options: [pci] [cardbus] [apm]
    May 2 11:32:34 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 2 11:32:34 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 11:32:34 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 11:32:34 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 11:32:34 loki kernel: ISA irqs (scanned) = 5,9,10 status change
    on irq 10
    May 2 11:32:34 loki cardmgr[3230]: watching 2 sockets
    May 2 11:32:35 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 11:32:35 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 11:32:35 loki cardmgr[3231]: unsupported card in socket 0
    May 2 11:32:35 loki cardmgr[3231]: no product info available
    May 2 11:32:35 loki cardmgr[3231]: PCI id: 0x1186, 0x1340
    May 2 11:38:38 loki cardmgr[3231]: exiting
    May 2 11:38:40 loki kernel: cs: cb_free(bus 1)
    May 2 11:38:40 loki kernel: unloading PCMCIA Card Services
    May 2 11:38:40 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 2 11:38:40 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 2 11:38:40 loki kernel: options: [pci] [cardbus] [apm]
    May 2 11:38:41 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 2 11:38:41 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 11:38:41 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 11:38:41 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 11:38:41 loki kernel: ISA irqs (scanned) = 5,9,10 polling
    interval = 1000 ms
    May 2 11:38:41 loki cardmgr[3291]: watching 2 sockets
    May 2 11:38:42 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 11:38:42 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 11:38:42 loki cardmgr[3292]: unsupported card in socket 0
    May 2 11:38:42 loki cardmgr[3292]: no product info available
    May 2 11:38:42 loki cardmgr[3292]: PCI id: 0x1186, 0x1340
    May 2 11:40:51 loki kernel: cs: cb_free(bus 1)
    May 2 11:40:57 loki cardmgr[3292]: exiting
    May 2 11:40:57 loki kernel: unloading PCMCIA Card Services
    May 2 11:40:58 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 2 11:40:58 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 2 11:40:58 loki kernel: options: [pci] [cardbus] [apm]
    May 2 11:40:58 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 2 11:40:58 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 11:40:58 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 11:40:58 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 11:40:58 loki kernel: ISA irqs (scanned) = 5,9,10 polling
    interval = 1000 ms
    May 2 11:40:59 loki cardmgr[3347]: watching 2 sockets
    May 2 11:56:57 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 11:56:57 loki cardmgr[3348]: unsupported card in socket 0
    May 2 11:56:57 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 11:56:57 loki cardmgr[3348]: no product info available
    May 2 11:56:57 loki cardmgr[3348]: PCI id: 0x1186, 0x1340
    May 2 11:57:26 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 11:57:26 loki last message repeated 2 times
    May 2 12:00:10 loki cardmgr[3348]: exiting
    May 2 12:00:12 loki kernel: cs: cb_free(bus 1)
    May 2 12:00:12 loki kernel: unloading PCMCIA Card Services
    May 2 12:00:13 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 2 12:00:13 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 2 12:00:13 loki kernel: options: [pci] [cardbus] [apm]
    May 2 12:00:13 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 2 12:00:13 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 12:00:13 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 12:00:13 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 12:00:13 loki kernel: ISA irqs (scanned) = 5,10 polling interval
    = 1000 ms
    May 2 12:00:14 loki cardmgr[3438]: watching 2 sockets
    May 2 12:00:14 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 12:00:14 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 12:00:14 loki cardmgr[3439]: unsupported card in socket 0
    May 2 12:00:14 loki cardmgr[3439]: no product info available
    May 2 12:00:14 loki cardmgr[3439]: PCI id: 0x1186, 0x1340
    May 2 12:04:14 loki kernel: cs: could not allocate 4K memory for CardBus
    socket 0
    May 2 12:04:48 loki last message repeated 6 times
    May 2 12:04:48 loki last message repeated 2 times

    --cut--






    ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
    http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
    ----= East and West-Coast Server Farms - Total Privacy via Encryption =----

  2. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    Gary wrote:

    > The card gives me a low pitch beep on insertion and a high beep on eject.
    > The manfid is not correct, (0x1186, 0x1340) should be (0x149 ,0x0000) for
    > this card.


    The reported IDs are PCI IDs, not PCMCIA manfids. The reported IDs
    are correct. The PCMCIA manfids are different.

    > May 2 11:32:35 loki kernel: cs: could not allocate 4K memory for CardBus
    > socket 0


    This is your problem. I'm not sure why you're getting this error.

    Oh.

    Please put back the original, unmodified /etc/pcmcia/config and
    /etc/pcmcia/config.opts files. When you replaced the config file, you
    deleted the "source ./config.opts" line, hence, all your resource
    definitions are being completely ignored.

    -- Dave

  3. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    dhinds@sonic.net wrote:
    > Gary wrote:
    >
    >
    >>The card gives me a low pitch beep on insertion and a high beep on eject.
    >>The manfid is not correct, (0x1186, 0x1340) should be (0x149 ,0x0000) for
    >>this card.

    >
    >
    > The reported IDs are PCI IDs, not PCMCIA manfids. The reported IDs
    > are correct. The PCMCIA manfids are different.
    >
    >
    >>May 2 11:32:35 loki kernel: cs: could not allocate 4K memory for CardBus
    >>socket 0

    >
    >
    > This is your problem. I'm not sure why you're getting this error.
    >
    > Oh.
    >
    > Please put back the original, unmodified /etc/pcmcia/config and
    > /etc/pcmcia/config.opts files. When you replaced the config file, you
    > deleted the "source ./config.opts" line, hence, all your resource
    > definitions are being completely ignored.
    >
    > -- Dave

    from the Linux-PCMCIA-Config-HOWTO:

    Symptoms:

    * When a card is inserted, it is identified correctly but cannot be
    configured (high/low beep pattern).
    * One of the following messages will appear in the system log:

    RequestIO: Resource in use
    RequestIRQ: Resource in use
    RequestWindow: Resource in use
    GetNextTuple: No more items
    could not allocate nn IO ports for CardBus socket n
    could not allocate nnK memory for CardBus socket n
    could not allocate interrupt for CardBus socket n

    Interrupt starvation often indicates a problem with the interrupt probe
    (see Interrupt scan failures). In some cases, the probe will seem to
    work, but only report one or two available interrupts. Check your system
    log to see if the scan results look sensible. Disabling the probe and
    selecting interrupts manually should help.

    If the interrupt probe is not working properly, the socket driver may
    allocate an interrupt for monitoring card insertions, even when
    interrupts are too scarce for this to be a good idea. You can switch the
    controller to polled mode by setting PCIC_OPTS to ``poll_interval=100'.
    Or, if you have a CardBus controller and an older version of the PCMCIA
    drivers, try ``pci_csc=1'', which selects a PCI interrupt (if available)
    for card status changes.

    IO port starvation is fairly uncommon, but sometimes happens with cards
    that require large, contiguous, aligned regions of IO port space, or
    that only recognize a few specific IO port positions. The default IO
    port ranges in /etc/pcmcia/config.opts are normally sufficient, but may
    be extended. If this is the problem, try uncommenting the ``include port
    0x1000-0x17ff'' line in config.opts. In rare cases, starvation may
    indicate that the IO port probe failed (see IO port scan failures).

    Memory starvation is also uncommon with the default memory window
    settings in config.opts. CardBus cards may require larger memory regions
    than typical 16-bit cards. Since CardBus memory windows can be mapped
    anywhere in the host's PCI address space (rather than just in the
    640K-1MB ``hole'' in PC systems), it is helpful to specify large memory
    windows in high memory, such as 0xa0000000-0xa0ffffff.


    HTH

    --
    Cheers,

    Jim

    -begin sig-
    Opinions expressed in this message may or may not be representative of
    the opinions of its author. You decide.

    Web: http://www.dotware.co.uk
    http://www.dotware-entertainment.co.uk

    Portable: P4m 2.0, 1GB, 40GB, MX440/15" XGA@1600x1200, Wi-Fi, GPRS,
    DVD/CDRW, XPSP2/Knoppix
    Powerbook G3/400, 392MB, 20GB, Rage 128/15"@1024x768, Wi-Fi, DVD, Mac OS
    X 10.4 "Tiger" Dev. Build
    Desktop: AMD64 3200+@2.63GHz, 512MB, 80GB, FX5700LE/32" WXGA@2048x768,
    DVD+-RW, XPSP1/Debian
    FileServer: Athlon XP 2400+, 256MB, 2.72TB, Blind, MuLinux

    More but I'm not tellin' ya, there's a pool forming at your feet.
    -end sig-

  4. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    dhinds@sonic.net wrote:
    >
    > The reported IDs are PCI IDs, not PCMCIA manfids. The reported IDs
    > are correct. The PCMCIA manfids are different.
    >
    >> May 2 11:32:35 loki kernel: cs: could not allocate 4K memory for CardBus
    >> socket 0

    >
    > This is your problem. I'm not sure why you're getting this error.
    >
    > Oh.
    >
    > Please put back the original, unmodified /etc/pcmcia/config and
    > /etc/pcmcia/config.opts files. When you replaced the config file, you
    > deleted the "source ./config.opts" line, hence, all your resource
    > definitions are being completely ignored.
    >
    > -- Dave


    Hi Dave,

    My confusion with the pci id and the manfid.

    I restored the original config and config.opts as you stated. I'm still
    getting errors.

    I did a reboot to start clean. This is where I'm at now.

    cardctl config

    --cut--
    Socket 0:
    Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
    interface type is "cardbus"
    function 0:
    Socket 1:
    not configured
    --cut--

    cardctl ident

    --cut--
    Socket 0:
    product info: "D-Link", "DFE-690TXD", "PC Card"
    manfid: 0x0149, 0x0000
    function: 6 (network)
    PCI id: 0x1186, 0x1340
    Socket 1:
    no product info available
    --cut--

    cardctl info

    --cut--
    PRODID_1="D-Link"
    PRODID_2="DFE-690TXD"
    PRODID_3="PC Card"
    PRODID_4=""
    MANFID=0149,0000
    FUNCID=6
    PRODID_1=""
    PRODID_2=""
    PRODID_3=""
    PRODID_4=""
    MANFID=0000,0000
    FUNCID=255
    --cut--

    cardctl status

    --cut--
    Socket 0:
    3.3V CardBus card
    function 0: [ready]
    Socket 1:
    no card
    --cut--

    I noticed the Ethernet controller is id on Bus 1 device 0. Could this be the
    pcilib problem?

    cat /proc/pci
    --cut--
    PCI devices found:
    Bus 0, device 0, function 0:
    Host bridge: Intel Corp. 430MX - 82437MX Mob. System Ctrlr (MTSC) &
    82438MX Data Path (MTDP) (rev 2).
    Master Capable. Latency=32.
    Bus 0, device 1, function 0:
    ISA bridge: Intel Corp. 82371FB PIIX ISA [Triton I] (rev 2).
    Bus 0, device 2, function 0:
    CardBus bridge: Texas Instruments PCI1130 (rev 4).
    Master Capable. Latency=168. Min Gnt=128.
    Non-prefetchable 32 bit memory at 0x10211000 [0x10211fff].
    Bus 0, device 2, function 1:
    CardBus bridge: Texas Instruments PCI1130 (#2) (rev 4).
    Master Capable. Latency=168. Min Gnt=192.
    Non-prefetchable 32 bit memory at 0x10210000 [0x10210fff].
    Bus 0, device 3, function 0:
    VGA compatible controller: Trident Microsystems TGUI 9320 (rev 227).
    IRQ 11.
    Non-prefetchable 32 bit memory at 0x8000000 [0x81fffff].
    Non-prefetchable 32 bit memory at 0x8200000 [0x820ffff].
    Bus 1, device 0, function 0:
    Ethernet controller: (rev 16).
    Master Capable. No bursts. Min Gnt=32.Max Lat=64.
    --cut--

    lspci -vv -H1
    --cut--

    00:00.0 Host bridge: Intel Corp. 430MX - 82437MX Mob. System Ctrlr (MTSC) &
    82438MX Data Path (MTDP) (rev 02)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32

    00:01.0 ISA bridge: Intel Corp. 82371FB PIIX ISA [Triton I] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-> Gary
    wrote:
    >
    >> The card gives me a low pitch beep on insertion and a high beep on eject.
    >> The manfid is not correct, (0x1186, 0x1340) should be (0x149 ,0x0000) for
    >> this card. Stepping- SERR- FastB2B-

    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0

    00:02.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 168, cache line size 08
    Interrupt: pin A routed to IRQ 255
    Region 0: Memory at 10211000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=01, subordinate=03, sec-latency=176
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite-
    16-bit legacy interface ports at 0001

    00:02.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 168, cache line size 08
    Interrupt: pin B routed to IRQ 255
    Region 0: Memory at 10210000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=04, subordinate=06, sec-latency=176
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
    16-bit legacy interface ports at 0001

    00:03.0 VGA compatible controller: Trident Microsystems TGUI 9320 (rev e3)
    (prog-if 00 [VGA])
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- Gary
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at 08000000 (32-bit, non-prefetchable)
    Region 1: Memory at 08200000 (32-bit, non-prefetchable)

    01:00.0 Ethernet controller: D-Link System Inc DFE-690TXD CardBus PC Card
    (rev 10)
    Subsystem: D-Link System Inc DFE-690TXD CardBus PC Card
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin A routed to IRQ 255
    Region 0: I/O ports at [disabled]
    Region 1: Memory at 60000000 (32-bit, non-prefetchable)
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    --cut--

    /var/log/messages

    --cut--
    May 2 16:14:36 loki kernel: scsi0 : SCSI host adapter emulation for IDE
    ATAPI devices
    May 2 16:14:37 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 2 16:14:37 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 2 16:14:37 loki kernel: options: [pci] [cardbus] [apm]
    May 2 16:14:37 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 2 16:14:37 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 2 16:14:37 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 2 16:14:37 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 2 16:14:37 loki kernel: ISA irqs (scanned) = 5,10 polling interval
    = 1000 ms
    May 2 16:14:38 loki cardmgr[83]: watching 2 sockets
    May 2 16:14:38 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 2 16:14:38 loki cardmgr[84]: unsupported card in socket 0
    May 2 16:14:38 loki cardmgr[84]: product info: "D-Link", "DFE-690TXD",ls
    -al /proc/bus/pci
    --cut--
    dr-xr-xr-x 3 root root 0 2005-05-02 17:00 ./
    dr-xr-xr-x 4 root root 0 2005-05-02 17:00 ../
    dr-xr-xr-x 2 root root 0 2005-05-02 17:00 00/
    -r--r--r-- 1 root root 0 2005-05-02 17:00 devices
    --cut -- "PC Card"
    May 2 16:14:38 loki cardmgr[84]: manfid: 0x0149, 0x0000 function: 6
    (network)
    May 2 16:14:38 loki cardmgr[84]: PCI id: 0x1186, 0x1340
    May 2 16:14:43 loki logger: /etc/rc.d/rc.inet1: /sbin/ifconfig lo
    127.0.0.1
    May 2 16:14:43 loki logger: /etc/rc.d/rc.inet1: /sbin/route add -net
    127.0.0.0 netmask 255.0.0.0 lo
    May 2 16:14:45 loki logger: /etc/rc.d/rc.inet1: /sbin/route add default gw
    192.168.0.1 metric 1
    May 2 16:14:45 loki logger: SIOCADDRT: Network is unreachable
    May 2 16:14:47 loki sshd[137]: Server listening on 0.0.0.0 port 22.
    May 2 16:15:07 loki kernel: parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
    May 2 16:15:07 loki kernel: lp0: using parport0 (polling).
    --cut--

    partial dmesg
    --cut--
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,10 polling interval = 1000 ms
    cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
    lp0: using parport0 (polling).
    --cut--

    ls -al /proc/bus/pci

    --cut--
    dr-xr-xr-x 3 root root 0 2005-05-02 17:00 ./
    dr-xr-xr-x 4 root root 0 2005-05-02 17:00 ../
    dr-xr-xr-x 2 root root 0 2005-05-02 17:00 00/
    -r--r--r-- 1 root root 0 2005-05-02 17:00 devices
    --cut --

    ls -al /proc/bus/pci/00/
    --cut--
    total 5
    dr-xr-xr-x 2 root root 0 2005-05-02 17:01 ./
    dr-xr-xr-x 3 root root 0 2005-05-02 17:01 ../
    -rw-r--r-- 1 root root 256 2005-05-02 17:01 00.0
    -rw-r--r-- 1 root root 256 2005-05-02 17:01 01.0
    -rw-r--r-- 1 root root 256 2005-05-02 17:01 02.0
    -rw-r--r-- 1 root root 256 2005-05-02 17:01 02.1
    -rw-r--r-- 1 root root 256 2005-05-02 17:01 03.0
    --cut--

    I'm curious about the pcilib error. It seems that the device is not in the
    proc tree. Yet it attempts to access it.

    May not be relative but I'm not certain at this point.

    Regards and Godspeed,
    Gary

    The magic is in the Magician not the wand!


    ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
    http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
    ----= East and West-Coast Server Farms - Total Privacy via Encryption =----

  5. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    Gary wrote:

    > I restored the original config and config.opts as you stated. I'm still
    > getting errors.


    > I did a reboot to start clean. This is where I'm at now.


    > Socket 0:
    > product info: "D-Link", "DFE-690TXD", "PC Card"
    > manfid: 0x0149, 0x0000
    > function: 6 (network)
    > PCI id: 0x1186, 0x1340


    That looks good.

    Now you need to add some lines to the config file (don't remove any)
    for your card.

    I would try:

    card "D-Link DFE-690TXD"
    manfid 0x0149, 0x0000
    bind "dummy_cb"

    Plug the card in, and verify that "dummy_cb" is loaded.

    Then do "modprobe 8139too".

    > I noticed the Ethernet controller is id on Bus 1 device 0. Could this be the
    > pcilib problem?


    The pcilib problem is a limitation of running the pcmcia-cs modules on
    a 2.4 kernel. It is harmless, other than interfering with 'lspci'.

    -- Dave

  6. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    Hi,

    Joy! Joy! Joy!

    After restoring the /etc/pcmcia/config & /etc/pcmcia/config.opts to the
    original state. Then;

    Add to /etc/pcmcia/config

    #Ethernet adapter
    #
    #05-03-05 11:30 gws

    card "D-Link", "DFE-690TXD", "PC Card"
    manfid 0x149, 0x0000
    bind "tulip"

    add to /etc/pcmcia/config.opts

    include port 0x1000-0x17ff

    #comment out token ring
    #include port 0xa00-0xaff

    add to /etc/rc.d/rc.pcmcia

    PCIC_OPTS="poll_interval=100 pci_esc=1"

    Then /etc/rc.d/rc.pcmcia restart

    I got an irq 5 io 0x1000 for the tulip module.

    I was able to configure eth0 but still no joy. I then remembered that I had
    a driver for the Realtek chipset. It was cardbus_DFE-690TXD from;

    http://personal.riverusers.com/~lapeyre/computers.html

    I rebuilt the pcmcia-3.2.8 then I edited the Makefile for the
    cardbus_DFE-690TXD to point to my source tree and version. Plus point to
    the PCMCIA=/home/build/pcmcia-cs-3.2.8.

    I then make;
    to get pci-scan.o cb_shim.o and rtl8139.o.

    I copied the .0 files via floppy to the notebook;

    /lib/modules/2.4.29pentium/pcmcia

    I then edited the /etc/pcmcia/config

    add;

    device "realtek"
    class "network" module "cb_enabler", "pci-scan", "cb_shim", "rtl8139"


    add;

    #Ethernet adapter
    #690TXD
    card "D-Link", "DFE-690TXD", "PC Card"
    manfid 0x149, 0x0000
    bind "realtek"

    Then;

    /etc/rc.d/rc.pcmcia restart

    ifconfig eth0 192.168.0.3

    route add default gw 192.168.0.1

    netdate time.mtco.com

    joy! Joy! Joy!

    I am getting warnings for "cb_enabler", "pci-scan", "cb_shim", "rtl8139".
    as modules that will taint the kernel.

    /var/log/messages partial;

    --cut--
    May 3 12:02:32 loki kernel: cs: cb_free(bus 1)
    May 3 12:02:32 loki kernel: unloading PCMCIA Card Services
    May 3 12:02:33 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 3 12:02:33 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 3 12:02:33 loki kernel: options: [pci] [cardbus] [apm]
    May 3 12:02:33 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 3 12:02:33 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 3 12:02:33 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 3 12:02:33 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 3 12:02:33 loki kernel: ISA irqs (scanned) = 5,7,9,10 polling
    interval = 1000 ms
    May 3 12:02:34 loki cardmgr[815]: watching 2 sockets
    May 3 12:02:34 loki kernel: cs: cb_alloc(bus 1): vendor 0x1186, device
    0x1340
    May 3 12:02:34 loki cardmgr[816]: socket 0: D-Link DFE-690TXD
    May 3 12:02:35 loki cardmgr[816]: executing: 'modprobe pci-scan 2>&1'
    May 3 12:02:35 loki cardmgr[816]: + Warning:
    loading /lib/modules/2.4.29pentium/pcmcia/pci-scan.o will taint the kernel:
    no license
    May 3 12:02:35 loki cardmgr[816]: + See
    http://www.tux.org/lkml/#export-tainted for information about tainted
    modules
    May 3 12:02:35 loki cardmgr[816]: + Module pci-scan loaded, with warnings
    May 3 12:02:36 loki cardmgr[816]: executing: 'modprobe cb_shim 2>&1'
    May 3 12:02:36 loki cardmgr[816]: + Warning:
    loading /lib/modules/2.4.29pentium/pcmcia/cb_shim.o will taint the kernel:
    no license
    May 3 12:02:36 loki cardmgr[816]: + See
    http://www.tux.org/lkml/#export-tainted for information about tainted
    modules
    May 3 12:02:36 loki kernel: cb_shim.c:v1.00 4/15/2000 Donald Becker

    May 3 12:02:36 loki kernel: http://www.scyld.com/linux/drivers.html
    May 3 12:02:36 loki cardmgr[816]: + Module cb_shim loaded, with warnings
    May 3 12:02:36 loki cardmgr[816]: executing: 'modprobe rtl8139 2>&1'
    May 3 12:02:36 loki cardmgr[816]: + Warning:
    loading /lib/modules/2.4.29pentium/pcmcia/rtl8139.o will taint the kernel:
    no license
    May 3 12:02:36 loki cardmgr[816]: + See
    http://www.tux.org/lkml/#export-tainted for information about tainted
    modules
    May 3 12:02:36 loki kernel: rtl8139.c:v1.16a 11/13/2001 Donald Becker,
    becker@scyld.com.
    May 3 12:02:36 loki kernel: http://www.scyld.com/network/rtl8139.html
    May 3 12:02:36 loki cardmgr[816]: + Module rtl8139 loaded, with warnings
    May 3 12:02:36 loki kernel: cs: cb_config(bus 1)
    May 3 12:02:36 loki kernel: cs: IO port probe 0x0100-0x03af: excluding
    0x1a0-0x1af 0x220-0x22f 0x268-0x26f 0x330-0x337 0x388-0x38f
    May 3 12:02:36 loki kernel: cs: IO port probe 0x03e0-0x04ff: excluding
    0x4d0-0x4d7
    May 3 12:02:36 loki kernel: cs: IO port probe 0x0800-0x080f: clean.
    May 3 12:02:36 loki kernel: cs: IO port probe 0x0820-0x08ff: clean.
    May 3 12:02:36 loki kernel: cs: IO port probe 0x0c00-0x0cff: clean.
    May 3 12:02:36 loki kernel: cs: IO port probe 0x1000-0x17ff: excluding
    0x1268-0x126f 0x13b8-0x13bf 0x13f0-0x13f7 0x15e8-0x15ef 0x1668-0x166f
    0x17b8-0x17bf 0x17f0-0x17f7
    May 3 12:02:36 loki kernel: fn 0 bar 1: io 0x1100-0x11ff
    May 3 12:02:36 loki kernel: fn 0 bar 2: mem 0x60001000-0x600011ff
    May 3 12:02:36 loki kernel: irq 5
    May 3 12:02:36 loki kernel: Found a D-Link DFE-690TXD (RealTek RTL8139) at
    1/0 address 0x1101->0x1100 IRQ 5.
    May 3 12:02:36 loki kernel: D-Link DFE-690TXD (RealTek RTL8139) at 1/0
    command 0x7.
    May 3 12:02:36 loki kernel: eth0: D-Link DFE-690TXD (RealTek RTL8139) at
    0x1100, IRQ 5, 00:0d:88:1b:79:75.
    May 3 12:28:36 loki -- MARK --
    --cut--

    Thanks Jim and Dave for the feedback.

    Now off too get the wireless working for these laptops.

    Regards and Godspeed,
    Gary

    The magic is in the Magician not the wand!










    ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
    http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
    ----= East and West-Coast Server Farms - Total Privacy via Encryption =----

  7. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    dhinds@sonic.net wrote:

    > Gary wrote:
    >
    >> I restored the original config and config.opts as you stated. I'm still
    >> getting errors.

    >
    >> I did a reboot to start clean. This is where I'm at now.

    >
    >> Socket 0:
    >> product info: "D-Link", "DFE-690TXD", "PC Card"
    >> manfid: 0x0149, 0x0000
    >> function: 6 (network)
    >> PCI id: 0x1186, 0x1340

    >
    > That looks good.
    >
    > Now you need to add some lines to the config file (don't remove any)
    > for your card.
    >
    > I would try:
    >
    > card "D-Link DFE-690TXD"
    > manfid 0x0149, 0x0000
    > bind "dummy_cb"
    >
    > Plug the card in, and verify that "dummy_cb" is loaded.
    >
    > Then do "modprobe 8139too".
    >
    >> I noticed the Ethernet controller is id on Bus 1 device 0. Could this be
    >> the pcilib problem?

    >
    > The pcilib problem is a limitation of running the pcmcia-cs modules on
    > a 2.4 kernel. It is harmless, other than interfering with 'lspci'.
    >
    > -- Dave


    Hi,

    Dave, I tried the dummy_cb and a cold boot instead of the modprobe. The
    reason for the cold boot was that I had a freeze. I had placed the bind
    "dummy_cb" in the /etc/pcmcia/config file. Then eject the card, when I
    tried to insert it again, it beeped low. Then I couldn't get any keyboard
    response. No other terminals. No ethernet so a ssh was out of the question.

    After the reboot the card was recognized and configured. Go figure!

    I would rather use it this way then to have problems with the rtl8139
    configuration.

    I notice on the re-boot that; pcilib: Cannot open /proc/bus/pci/01/00.0
    responded four times before continuing. This was just after the eth0:
    configuration. Notice the oops!

    I did another cold boot to see if it was just a quirk the first time. It
    remained the same.

    I will continue to find out why and how this is working this way. I
    appreciate any help that you have given me. Thanks!

    Regards and Godspeed,
    Gary

    The Magic is in the Magician not the wand!


    dmesg partial;

    --cut--
    Linux PCMCIA Card Services 3.2.8
    kernel build: 2.4.29pentium #1 Tue Apr 26 18:12:22 CDT 2005
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: No IRQ known for interrupt pin A of device 00:02.0. Please try using
    pci=biosirq.
    PCI: No IRQ known for interrupt pin B of device 00:02.1. Please try using
    pci=biosirq.
    TI 1130 rev 04 PCI-to-CardBus at slot 00:02, mem 0x10211000
    host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 1/3]
    host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 4/6]
    ISA irqs (scanned) = 5,7,9,10 polling interval = 1000 ms
    Unable to handle kernel NULL pointer dereference at virtual address 0000002c
    printing eip:
    c02208c6
    *pde = 00000000
    Oops: 0000
    CPU: 0
    EIP: 0010:[] Not tainted
    EFLAGS: 00010046
    eax: 00000087 ebx: 00000246 ecx: 0000001c edx: 00000014
    esi: 0000001c edi: c35d9088 ebp: c35f7b30 esp: c35f7b00
    ds: 0018 es: 0018 ss: 0018
    Process cardctl (pid: 87, stackpage=c35f7000)
    Stack: c35d9000 c4822c2b 0000001c 00000014 ffffffff 00000000 00000014
    00000000
    c109408c 00000002 c35f7bf2 00000000 c35f7b80 c4821c20 c35d9000
    00000002
    40016410 00000001 c367d058 c3c92440 c3997ea0 c3c9245c 40016410
    c011627d
    Call Trace: [] [] [] []
    []
    [] [] [] [] []
    []
    [] [] [] [] []
    []
    [] [] [] [] []
    []
    [] [] [] [] []
    []
    [] [] [] [] []
    []
    [] [] [] [] []
    []

    Code: 8b 41 10 8b 40 30 ff 74 24 10 52 51 ff 50 14 83 c4 0c 53 9d
    <6>cs: cb_alloc(bus 1): vendor 0x1186, device 0x1340
    cs: cb_config(bus 1)
    cs: IO port probe 0x0100-0x03af: excluding 0x1a0-0x1af 0x220-0x22f
    0x268-0x26f 0x330-0x337 0x388-0x38f
    cs: IO port probe 0x03e0-0x04ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x0800-0x080f: clean.
    cs: IO port probe 0x0820-0x08ff: clean.
    cs: IO port probe 0x0c00-0x0cff: clean.
    cs: IO port probe 0x1000-0x17ff: excluding 0x1268-0x126f 0x13b8-0x13bf
    0x13f0-0x13f7 0x15e8-0x15ef 0x1668-0x166f 0x17b8-0x17bf 0x17f0-0x17f7
    fn 0 bar 1: io 0x1000-0x10ff
    fn 0 bar 2: mem 0x60001000-0x600011ff
    irq 5
    cs: cb_enable(bus 1)
    bridge io map 0 (flags 0x21): 0x1000-0x10ff
    bridge mem map 0 (flags 0x1): 0x60001000-0x60001fff
    dummy_attach(device 01:00.0)
    8139too Fast Ethernet driver 0.9.26
    eth0: RealTek RTL8139 at 0xc4848000, 00:0d:88:1b:79:75, IRQ 5
    eth0: Identified 8139 chip type 'RTL-8139C'
    eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
    parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
    lp0: using parport0 (polling).

    --cut--

    /var/log/messages partitial

    --cut--
    May 3 23:07:40 loki kernel: Linux PCMCIA Card Services 3.2.8
    May 3 23:07:40 loki kernel: kernel build: 2.4.29pentium #1 Tue Apr 26
    18:12:22 CDT 2005
    May 3 23:07:40 loki kernel: options: [pci] [cardbus] [apm]
    May 3 23:07:40 loki kernel: Intel ISA/PCI/CardBus PCIC probe:
    May 3 23:07:40 loki kernel: TI 1130 rev 04 PCI-to-CardBus at slot 00:02,
    mem 0x10211000
    May 3 23:07:40 loki kernel: host opts [0]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 1/3]
    May 3 23:07:40 loki kernel: host opts [1]: [ring] [isa irq] [no pci
    irq] [lat 168/176] [bus 4/6]
    May 3 23:07:40 loki kernel: ISA irqs (scanned) = 5,7,9,10 polling
    interval = 1000 ms
    May 3 23:07:42 loki cardmgr[99]: watching 2 sockets
    May 3 23:07:42 loki cardmgr[100]: socket 0: D-Link DFE-690TXD
    May 3 23:07:43 loki kernel: cs: cb_config(bus 1)
    May 3 23:07:43 loki kernel: cs: IO port probe 0x0100-0x03af: excluding
    0x1a0-0x1af 0x220-0x22f 0x268-0x26f 0x330-0x337 0x388-0x38f
    May 3 23:07:43 loki kernel: cs: IO port probe 0x03e0-0x04ff: excluding
    0x4d0-0x4d7
    May 3 23:07:43 loki kernel: cs: IO port probe 0x0800-0x080f: clean.
    May 3 23:07:43 loki kernel: cs: IO port probe 0x0820-0x08ff: clean.
    May 3 23:07:43 loki kernel: cs: IO port probe 0x0c00-0x0cff: clean.
    May 3 23:07:43 loki kernel: cs: IO port probe 0x1000-0x17ff: excluding
    0x1268-0x126f 0x13b8-0x13bf 0x13f0-0x13f7 0x15e8-0x15ef 0x1668-0x166f
    0x17b8-0x17bf 0x17f0-0x17f7
    May 3 23:07:43 loki kernel: fn 0 bar 1: io 0x1000-0x10ff
    May 3 23:07:43 loki kernel: fn 0 bar 2: mem 0x60001000-0x600011ff
    May 3 23:07:43 loki kernel: irq 5
    May 3 23:07:43 loki kernel: dummy_attach(device 01:00.0)
    May 3 23:07:48 loki logger: /etc/rc.d/rc.inet1: /sbin/ifconfig lo
    127.0.0.1
    May 3 23:07:48 loki logger: /etc/rc.d/rc.inet1: /sbin/route add -net
    127.0.0.0 netmask 255.0.0.0 lo
    May 3 23:07:49 loki logger: /etc/rc.d/rc.inet1: /sbin/route add default gw
    192.168.0.1 metric 1
    May 3 23:07:49 loki logger: SIOCADDRT: Network is unreachable
    May 3 23:07:49 loki logger: /etc/rc.d/rc.hotplug start (entering script)
    May 3 23:07:50 loki udevsend[156]: udevd daemon started
    May 3 23:07:52 loki kernel: 8139too Fast Ethernet driver 0.9.26
    May 3 23:07:52 loki kernel: eth0: RealTek RTL8139 at 0xc4848000,
    00:0d:88:1b:79:75, IRQ 5
    May 3 23:07:53 loki logger: /etc/rc.d/rc.inet1: /sbin/ifconfig eth0
    192.168.0.3 broadcast 192.168.0.255 netmask 255.255.255.0
    May 3 23:07:54 loki kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
    May 3 23:07:56 loki logger: /etc/rc.d/rc.inet1: /sbin/route add default gw
    192.168.0.1 metric 1
    May 3 23:08:01 loki logger: /etc/rc.d/rc.hotplug start (exiting script)
    May 3 23:08:03 loki sshd[444]: Server listening on 0.0.0.0 port 22.
    May 3 23:08:22 loki kernel: parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
    May 3 23:08:22 loki kernel: lp0: using parport0 (polling).
    May 3 23:21:43 loki sshd[546]: Accepted password for root from 192.168.0.4
    port 34074 ssh2
    --cut--


    ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
    http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
    ----= East and West-Coast Server Farms - Total Privacy via Encryption =----

  8. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    Gary wrote:
    > dhinds@sonic.net wrote:
    >
    >
    >>Gary wrote:
    >>
    >>
    >>>I restored the original config and config.opts as you stated. I'm still
    >>>getting errors.

    >>
    >>>I did a reboot to start clean. This is where I'm at now.

    >>
    >>>Socket 0:
    >>> product info: "D-Link", "DFE-690TXD", "PC Card"
    >>> manfid: 0x0149, 0x0000
    >>> function: 6 (network)
    >>> PCI id: 0x1186, 0x1340

    >>
    >>That looks good.
    >>
    >>Now you need to add some lines to the config file (don't remove any)
    >>for your card.
    >>
    >>I would try:
    >>
    >> card "D-Link DFE-690TXD"
    >> manfid 0x0149, 0x0000
    >> bind "dummy_cb"
    >>
    >>Plug the card in, and verify that "dummy_cb" is loaded.
    >>
    >>Then do "modprobe 8139too".
    >>
    >>
    >>>I noticed the Ethernet controller is id on Bus 1 device 0. Could this be
    >>>the pcilib problem?

    >>
    >>The pcilib problem is a limitation of running the pcmcia-cs modules on
    >>a 2.4 kernel. It is harmless, other than interfering with 'lspci'.
    >>
    >>-- Dave

    >
    >
    > Hi,
    >
    > Dave, I tried the dummy_cb and a cold boot instead of the modprobe. The
    > reason for the cold boot was that I had a freeze. I had placed the bind
    > "dummy_cb" in the /etc/pcmcia/config file. Then eject the card, when I
    > tried to insert it again, it beeped low. Then I couldn't get any keyboard
    > response. No other terminals. No ethernet so a ssh was out of the question.
    >
    > After the reboot the card was recognized and configured. Go figure!



    My usual course of action (on XP anyway, I let Knoppix take care of
    cardbus config on my portable) in situations like these is to set the
    cardbus IRQs in the BIOS, rather than setting it all to "auto". Takes
    care of things nicely, although it makes things a bit unstable as far as
    hotplugging goes.

    --
    Cheers,

    Jim

    -begin sig-
    Opinions expressed in this message may or may not be representative of
    the opinions of its author. You decide.

    Web: http://www.dotware.co.uk
    http://www.dotware-entertainment.co.uk

    Portable: P4m 2.0, 1GB, 40GB, MX440/15" XGA@1600x1200, Wi-Fi, GPRS,
    DVD/CDRW, XPSP2/Knoppix
    Powerbook G3/400, 392MB, 20GB, Rage 128/15"@1024x768, Wi-Fi, DVD, Mac OS
    X 10.4 "Tiger" Dev. Build
    Desktop: AMD64 3200+@2.63GHz, 512MB, 80GB, FX5700LE/32" WXGA@2048x768,
    DVD+-RW, XPSP1/Debian
    FileServer: Athlon XP 2400+, 256MB, 2.72TB, Blind, MuLinux

    More but I'm not tellin' ya, there's a pool forming at your feet.
    -end sig-

  9. Re: Re-visit: Thinkpad 760el D-Link dfe-690-txd problems

    Jim wrote:

    >
    > My usual course of action (on XP anyway, I let Knoppix take care of
    > cardbus config on my portable) in situations like these is to set the
    > cardbus IRQs in the BIOS, rather than setting it all to "auto". Takes
    > care of things nicely, although it makes things a bit unstable as far as
    > hotplugging goes.
    >

    Hi,

    Jim, with the Thinkpad 760el I do not have the option to configure the bios
    irq. It would be nice to have that option at the bios level but the
    configuration must be done via utility and that too is limited for these
    older laptops.

    I tried several live cd os on the 760el, knoppix,slax and DSL. No joy. With
    Knoppix it would not configure the card. Slax and DamnSmall ignored
    completely.

    I do have issues with hotplugging on this laptop. The only reason I'm trying
    to use such an antique, is that they are cheap and will make a good small
    controller. Not if I had to account for the time spent on this pcmcia
    problems! :-)

    Thanks for the feedback!

    --
    Regards and Godspeed,
    Gary

    The magic is in the Magician not the wand!

    ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
    http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
    ----= East and West-Coast Server Farms - Total Privacy via Encryption =----

+ Reply to Thread