Hi all,

>From this version of HPN, SO_RCVBUF can be set with the "TcpRcvBuf" option

on the client scp, but the scp launched by the sshd does not call the
setsockopt(). As a result the performance of scp is good when download a
file from remote-to-local but not when upload a file from local-to-remote.
Can you tell me what configuation settings makes the local-to-remote file
transfer faster and to get better throughput? Why don't we have an option
simillar to "TcpRcvBuf" for sshd ?

Regards,
M.P

----- Original Message -----
From: "Chris Rapier"
To:
Sent: Saturday, May 20, 2006 3:03 AM
Subject: New HPN Patch Released


> The HPN12 patch available from
> http://www.psc.edu/networking/projects/hpn-ssh addresses performance
> issues with bulk data transfer over high bandwidth delay paths. By
> adjusting internal flow control buffers to better fit the outstanding
> data capacity of the path significant improvements in bulk data
> throughput performance are achieved.
>
> In other words, transfers over the internet are a lot faster with this
> patch. Increase in performance of more than an order of magnitude are
> pretty common. If you make use of the now included NONE cipher I've hit
> data rates of more than 800Mbps between Pittsburgh and Chicago and
> 650Mbps between Pittsburgh and San Diego. The NONE cipher is only used
> during the bulk data transfer and *not* during authentication. This
> version of the patch makes the NONE cipher a server side configuration
> option so you don't have to enable it if you don't want to.
>
> Command line switches have been abandoned in favor of configuration
> options which are outlined below and in the HPN12-README included in the
> patch.
>
> Other versions of the patch showed some performance decrease in local
> area network transfers. I've addressed this by changing the size of one
> of the buffers (thanks Darren) and giving people the option of turning
> off HPN functionality. I've done my best to verify this by running
> several thousand tests and analyzing the results. These results are
> available from http://www.psc.edu/networking/projec...h/results.html
> However, there is always the chance that new problems have been
> introduced that didn't show up in my environment. So while I am
> reasonably confident there are no problems with this patch use al
> appropriate caution especially in production environments.
>
>
> Configuration options for HPN:
> TcpRcvBuf=[int] (KB) client
> set the TCP socket receive buffer to n Kilobytes. It can be set
> up to the maximum socket size allowed by the system. This is useful in
> situations where the tcp receive window is set low but the maximum
> buffer size is set higher (as is typical). This works on a per TCP
> connection basis. You can also use this to artificially limit the
> transfer rate of the connection. In these cases the throughput will be
> no more than n/RTT. The minimum buffer size is 1KB. Default is the
> current system wide tcp receive buffer size.
>
> TcpRcvBufPoll=[yes/no] client/server
> enable of disable the polling of the tcp receive buffer through
> the life of the connection. You would want to make sure that this option
> is enabled for systems making use of autotuning kernels (linux 2.4.24+,
> 2.6, MS Vista) default is no.
>
> NoneEnabled=[yes/no] client/server
> enable or disable the use of the None cipher. Care must always be
> used when enabling this as it will allow users to send data in the
> clear. However, it is important to note that authentication information
> remains encrypted even if this option is enabled. Set to no by default.
>
> NoneSwitch=[yes/no] client
> Switch the encryption cipher being used to the None cipher after
> authentication takes place. NoneEnabled must be enabled on both the
> client and server side of the connection. The connection attempt will
> fail with an error if a client requests a NoneSwitch from the server
> that does not explicitly have NoneEnabled set to yes. Set to no by
> default.
>
> HPNDisabled=[yes/no] client/server
> In some situations, such as transfers on a local area network, the
> impact of the HPN code produces a net decrease in performance. In these
> cases it is helpful to disable the HPN functionality. By default
> HPNDisabled is set to no.
>
> HPNBufferSize=[int] (KB) client/server
> This is the default buffer size the HPN functionality uses when
> interacting with nonHPN SSH installations. Conceptually this is similar
> to the TcpRcvBuf option as applied to the internal SSH flow control.
> This value can range from 1KB to 14MB (1-14336). Use of oversized or
> undersized buffers can cause performance problems depending on the
> length of the network path. The default size of this buffer is 2MB.
> TcpRcvBufPoll, if set to yes, will override this value. This behaviour
> may change in future versions.
>
>
> Comments, questions, and especially critiques are always welcome.
> Note: I did not attach the patch, as is customary, because its around
> 1900 lines.
>
>
> Chris Rapier
> Network Research & Application Engineer
> Pittsburgh Supercomputing Center
>
> _______________________________________________
> openssh-unix-dev mailing list
> openssh-unix-dev@mindrot.org
> http://www.mindrot.org/mailman/listi...enssh-unix-dev


_______________________________________________
openssh-unix-dev mailing list
openssh-unix-dev@mindrot.org
http://www.mindrot.org/mailman/listi...enssh-unix-dev