2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB - Kernel

This is a discussion on 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB - Kernel ; Hello.. I had to write an image to some usb flash drives, more specifically, 4GB kingston datatraveler sticks, and i figured, instead of doing just 1 at a time, i may aswell do 4, so i plugged in 4, and ...

+ Reply to Thread
Results 1 to 4 of 4

Thread: 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB

  1. 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB

    Hello..

    I had to write an image to some usb flash drives, more specifically, 4GB
    kingston datatraveler sticks, and i figured, instead of doing just 1 at
    a time, i may aswell do 4, so i plugged in 4, and started 4 dd's of the
    images, to sdc, sdd, sde, sdf. However, i got usb disconnects and IO
    error messages from the kernel, these are at end of message. I had
    previously done ~5 writes of images to 5 other flash disks with no
    problem, but when i tried the next batch, those 4, it gave these errors.
    I killed the dd's, pulled them all out, and put in 1 at a time, and it
    worked perfectly.

    unfortunately the first kernel messages have been flooded away. If you
    need .config and/or the boot kernel messages, i can reboot and get it.

    this is on ICH9 ehci, from lspci:
    00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    Controller #4 (rev 02)
    00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    Controller #5 (rev 02)
    00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    Controller #6 (rev 02)
    00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
    Controller #2 (rev 02)
    00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    Controller #1 (rev 02)
    00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    Controller #2 (rev 02)
    00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    Controller #3 (rev 02)
    00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
    Controller #1 (rev 02)


    and the messages:
    usb 8-6: new high speed USB device using ehci_hcd and address 17
    usb 8-6: configuration #1 chosen from 1 choice
    scsi24 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 17
    usb-storage: waiting for device to settle before scanning
    scsi 24:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    ANSI: 0 CCS
    sd 24:0:0:0: [sdc] 7936000 512-byte hardware sectors (4063 MB)
    sd 24:0:0:0: [sdc] Write Protect is off
    sd 24:0:0:0: [sdc] Mode Sense: 23 00 00 00
    sd 24:0:0:0: [sdc] Assuming drive cache: write through
    sd 24:0:0:0: [sdc] 7936000 512-byte hardware sectors (4063 MB)
    sd 24:0:0:0: [sdc] Write Protect is off
    sd 24:0:0:0: [sdc] Mode Sense: 23 00 00 00
    sd 24:0:0:0: [sdc] Assuming drive cache: write through
    sdc: sdc1
    sd 24:0:0:0: [sdc] Attached SCSI removable disk
    usb-storage: device scan complete
    usb 8-5: new high speed USB device using ehci_hcd and address 18
    usb 8-5: configuration #1 chosen from 1 choice
    scsi25 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 18
    usb-storage: waiting for device to settle before scanning
    scsi 25:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    ANSI: 0 CCS
    sd 25:0:0:0: [sdd] 7936000 512-byte hardware sectors (4063 MB)
    sd 25:0:0:0: [sdd] Write Protect is off
    sd 25:0:0:0: [sdd] Mode Sense: 23 00 00 00
    sd 25:0:0:0: [sdd] Assuming drive cache: write through
    sd 25:0:0:0: [sdd] 7936000 512-byte hardware sectors (4063 MB)
    sd 25:0:0:0: [sdd] Write Protect is off
    sd 25:0:0:0: [sdd] Mode Sense: 23 00 00 00
    sd 25:0:0:0: [sdd] Assuming drive cache: write through
    sdd: sdd1
    sd 25:0:0:0: [sdd] Attached SCSI removable disk
    usb-storage: device scan complete
    usb 7-2: new high speed USB device using ehci_hcd and address 6
    usb 7-2: configuration #1 chosen from 1 choice
    scsi26 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 6
    usb-storage: waiting for device to settle before scanning
    scsi 26:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    ANSI: 0 CCS
    sd 26:0:0:0: [sde] 7936000 512-byte hardware sectors (4063 MB)
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 23 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    sd 26:0:0:0: [sde] 7936000 512-byte hardware sectors (4063 MB)
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 23 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    sde: sde1
    sd 26:0:0:0: [sde] Attached SCSI removable disk
    usb-storage: device scan complete
    usb 7-1: new high speed USB device using ehci_hcd and address 7
    usb 7-1: configuration #1 chosen from 1 choice
    scsi27 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 7
    usb-storage: waiting for device to settle before scanning
    scsi 27:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    ANSI: 0 CCS
    sd 27:0:0:0: [sdf] 7936000 512-byte hardware sectors (4063 MB)
    sd 27:0:0:0: [sdf] Write Protect is off
    sd 27:0:0:0: [sdf] Mode Sense: 23 00 00 00
    sd 27:0:0:0: [sdf] Assuming drive cache: write through
    sd 27:0:0:0: [sdf] 7936000 512-byte hardware sectors (4063 MB)
    sd 27:0:0:0: [sdf] Write Protect is off
    sd 27:0:0:0: [sdf] Mode Sense: 23 00 00 00
    sd 27:0:0:0: [sdf] Assuming drive cache: write through
    sdf: sdf1
    sd 27:0:0:0: [sdf] Attached SCSI removable disk
    usb-storage: device scan complete
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    end_request: I/O error, dev sde, sector 216960
    Buffer I/O error on device sde, logical block 27120
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27121
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27122
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27123
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27124
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27125
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27126
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27127
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 27128
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    end_request: I/O error, dev sde, sector 217200
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    __ratelimit: 97148 callbacks suppressed
    Buffer I/O error on device sde, logical block 124277
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124278
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124279
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124280
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124281
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124282
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124283
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124284
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124285
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 124286
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    __ratelimit: 152257 callbacks suppressed
    Buffer I/O error on device sde, logical block 276544
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276545
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276546
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276547
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276548
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276549
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276550
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276551
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276552
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 276553
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    __ratelimit: 170419 callbacks suppressed
    Buffer I/O error on device sde, logical block 446973
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446974
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446975
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446976
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446977
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446978
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446979
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446980
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446981
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 446982
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    __ratelimit: 152214 callbacks suppressed
    Buffer I/O error on device sde, logical block 599197
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599198
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599199
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599200
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599201
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599202
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599203
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599204
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599205
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 599206
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    __ratelimit: 165606 callbacks suppressed
    Buffer I/O error on device sde, logical block 764813
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764814
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764815
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764816
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764817
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764818
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764819
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764820
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764821
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 764822
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    __ratelimit: 165555 callbacks suppressed
    Buffer I/O error on device sde, logical block 930378
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930379
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930380
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930381
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930382
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930383
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930384
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930385
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930386
    lost page write due to I/O error on sde
    Buffer I/O error on device sde, logical block 930387
    lost page write due to I/O error on sde
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-1: USB disconnect, address 7
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 8-5: USB disconnect, address 18
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: reset high speed USB device using ehci_hcd and address 6
    usb 7-2: USB disconnect, address 6
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    sd 26:0:0:0: [sde] READ CAPACITY failed
    sd 26:0:0:0: [sde] Result: hostbyte=0x01 driverbyte=0x00
    sd 26:0:0:0: [sde] Sense not available.
    sd 26:0:0:0: [sde] Write Protect is off
    sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    sd 26:0:0:0: [sde] Assuming drive cache: write through
    usb 8-6: USB disconnect, address 17


    mvh.
    Kasper Sandberg

    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  2. Re: 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB

    (cc linux-usb)

    On Thu, 30 Oct 2008 06:22:49 +0100 Kasper Sandberg wrote:

    > Hello..
    >
    > I had to write an image to some usb flash drives, more specifically, 4GB
    > kingston datatraveler sticks, and i figured, instead of doing just 1 at
    > a time, i may aswell do 4, so i plugged in 4, and started 4 dd's of the
    > images, to sdc, sdd, sde, sdf. However, i got usb disconnects and IO
    > error messages from the kernel, these are at end of message. I had
    > previously done ~5 writes of images to 5 other flash disks with no
    > problem, but when i tried the next batch, those 4, it gave these errors.
    > I killed the dd's, pulled them all out, and put in 1 at a time, and it
    > worked perfectly.
    >
    > unfortunately the first kernel messages have been flooded away. If you
    > need .config and/or the boot kernel messages, i can reboot and get it.
    >
    > this is on ICH9 ehci, from lspci:
    > 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    > Controller #4 (rev 02)
    > 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    > Controller #5 (rev 02)
    > 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    > Controller #6 (rev 02)
    > 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
    > Controller #2 (rev 02)
    > 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    > Controller #1 (rev 02)
    > 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    > Controller #2 (rev 02)
    > 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
    > Controller #3 (rev 02)
    > 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
    > Controller #1 (rev 02)
    >
    >
    > and the messages:
    > usb 8-6: new high speed USB device using ehci_hcd and address 17
    > usb 8-6: configuration #1 chosen from 1 choice
    > scsi24 : SCSI emulation for USB Mass Storage devices
    > usb-storage: device found at 17
    > usb-storage: waiting for device to settle before scanning
    > scsi 24:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    > ANSI: 0 CCS
    > sd 24:0:0:0: [sdc] 7936000 512-byte hardware sectors (4063 MB)
    > sd 24:0:0:0: [sdc] Write Protect is off
    > sd 24:0:0:0: [sdc] Mode Sense: 23 00 00 00
    > sd 24:0:0:0: [sdc] Assuming drive cache: write through
    > sd 24:0:0:0: [sdc] 7936000 512-byte hardware sectors (4063 MB)
    > sd 24:0:0:0: [sdc] Write Protect is off
    > sd 24:0:0:0: [sdc] Mode Sense: 23 00 00 00
    > sd 24:0:0:0: [sdc] Assuming drive cache: write through
    > sdc: sdc1
    > sd 24:0:0:0: [sdc] Attached SCSI removable disk
    > usb-storage: device scan complete
    > usb 8-5: new high speed USB device using ehci_hcd and address 18
    > usb 8-5: configuration #1 chosen from 1 choice
    > scsi25 : SCSI emulation for USB Mass Storage devices
    > usb-storage: device found at 18
    > usb-storage: waiting for device to settle before scanning
    > scsi 25:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    > ANSI: 0 CCS
    > sd 25:0:0:0: [sdd] 7936000 512-byte hardware sectors (4063 MB)
    > sd 25:0:0:0: [sdd] Write Protect is off
    > sd 25:0:0:0: [sdd] Mode Sense: 23 00 00 00
    > sd 25:0:0:0: [sdd] Assuming drive cache: write through
    > sd 25:0:0:0: [sdd] 7936000 512-byte hardware sectors (4063 MB)
    > sd 25:0:0:0: [sdd] Write Protect is off
    > sd 25:0:0:0: [sdd] Mode Sense: 23 00 00 00
    > sd 25:0:0:0: [sdd] Assuming drive cache: write through
    > sdd: sdd1
    > sd 25:0:0:0: [sdd] Attached SCSI removable disk
    > usb-storage: device scan complete
    > usb 7-2: new high speed USB device using ehci_hcd and address 6
    > usb 7-2: configuration #1 chosen from 1 choice
    > scsi26 : SCSI emulation for USB Mass Storage devices
    > usb-storage: device found at 6
    > usb-storage: waiting for device to settle before scanning
    > scsi 26:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    > ANSI: 0 CCS
    > sd 26:0:0:0: [sde] 7936000 512-byte hardware sectors (4063 MB)
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 23 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > sd 26:0:0:0: [sde] 7936000 512-byte hardware sectors (4063 MB)
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 23 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > sde: sde1
    > sd 26:0:0:0: [sde] Attached SCSI removable disk
    > usb-storage: device scan complete
    > usb 7-1: new high speed USB device using ehci_hcd and address 7
    > usb 7-1: configuration #1 chosen from 1 choice
    > scsi27 : SCSI emulation for USB Mass Storage devices
    > usb-storage: device found at 7
    > usb-storage: waiting for device to settle before scanning
    > scsi 27:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0
    > ANSI: 0 CCS
    > sd 27:0:0:0: [sdf] 7936000 512-byte hardware sectors (4063 MB)
    > sd 27:0:0:0: [sdf] Write Protect is off
    > sd 27:0:0:0: [sdf] Mode Sense: 23 00 00 00
    > sd 27:0:0:0: [sdf] Assuming drive cache: write through
    > sd 27:0:0:0: [sdf] 7936000 512-byte hardware sectors (4063 MB)
    > sd 27:0:0:0: [sdf] Write Protect is off
    > sd 27:0:0:0: [sdf] Mode Sense: 23 00 00 00
    > sd 27:0:0:0: [sdf] Assuming drive cache: write through
    > sdf: sdf1
    > sd 27:0:0:0: [sdf] Attached SCSI removable disk
    > usb-storage: device scan complete
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > end_request: I/O error, dev sde, sector 216960
    > Buffer I/O error on device sde, logical block 27120
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27121
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27122
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27123
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27124
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27125
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27126
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27127
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 27128
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > end_request: I/O error, dev sde, sector 217200
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > __ratelimit: 97148 callbacks suppressed
    > Buffer I/O error on device sde, logical block 124277
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124278
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124279
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124280
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124281
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124282
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124283
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124284
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124285
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 124286
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > __ratelimit: 152257 callbacks suppressed
    > Buffer I/O error on device sde, logical block 276544
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276545
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276546
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276547
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276548
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276549
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276550
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276551
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276552
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 276553
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > __ratelimit: 170419 callbacks suppressed
    > Buffer I/O error on device sde, logical block 446973
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446974
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446975
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446976
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446977
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446978
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446979
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446980
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446981
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 446982
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > __ratelimit: 152214 callbacks suppressed
    > Buffer I/O error on device sde, logical block 599197
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599198
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599199
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599200
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599201
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599202
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599203
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599204
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599205
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 599206
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > __ratelimit: 165606 callbacks suppressed
    > Buffer I/O error on device sde, logical block 764813
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764814
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764815
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764816
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764817
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764818
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764819
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764820
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764821
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 764822
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > __ratelimit: 165555 callbacks suppressed
    > Buffer I/O error on device sde, logical block 930378
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930379
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930380
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930381
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930382
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930383
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930384
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930385
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930386
    > lost page write due to I/O error on sde
    > Buffer I/O error on device sde, logical block 930387
    > lost page write due to I/O error on sde
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-1: USB disconnect, address 7
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 8-5: USB disconnect, address 18
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: reset high speed USB device using ehci_hcd and address 6
    > usb 7-2: USB disconnect, address 6
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > sd 26:0:0:0: [sde] READ CAPACITY failed
    > sd 26:0:0:0: [sde] Result: hostbyte=0x01 driverbyte=0x00
    > sd 26:0:0:0: [sde] Sense not available.
    > sd 26:0:0:0: [sde] Write Protect is off
    > sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
    > sd 26:0:0:0: [sde] Assuming drive cache: write through
    > usb 8-6: USB disconnect, address 17
    >
    >
    > mvh.
    > Kasper Sandberg
    >


    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  3. Re: 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB

    On Fri, 31 Oct 2008, Andrew Morton wrote:

    > (cc linux-usb)
    >
    > On Thu, 30 Oct 2008 06:22:49 +0100 Kasper Sandberg wrote:
    >
    > > Hello..
    > >
    > > I had to write an image to some usb flash drives, more specifically, 4GB
    > > kingston datatraveler sticks, and i figured, instead of doing just 1 at
    > > a time, i may aswell do 4, so i plugged in 4, and started 4 dd's of the
    > > images, to sdc, sdd, sde, sdf. However, i got usb disconnects and IO
    > > error messages from the kernel, these are at end of message. I had
    > > previously done ~5 writes of images to 5 other flash disks with no
    > > problem, but when i tried the next batch, those 4, it gave these errors.
    > > I killed the dd's, pulled them all out, and put in 1 at a time, and it
    > > worked perfectly.


    Sounds like a hardware problem.

    Alan Stern

    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  4. Re: 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB

    On Fri, Oct 31, 2008 at 11:48:23PM -0700, Andrew Morton wrote:
    > (cc linux-usb)
    >
    > On Thu, 30 Oct 2008 06:22:49 +0100 Kasper Sandberg wrote:
    >
    > > Hello..
    > >
    > > I had to write an image to some usb flash drives, more specifically, 4GB
    > > kingston datatraveler sticks, and i figured, instead of doing just 1 at
    > > a time, i may aswell do 4, so i plugged in 4, and started 4 dd's of the
    > > images, to sdc, sdd, sde, sdf. However, i got usb disconnects and IO
    > > error messages from the kernel, these are at end of message. I had
    > > previously done ~5 writes of images to 5 other flash disks with no
    > > problem, but when i tried the next batch, those 4, it gave these errors.
    > > I killed the dd's, pulled them all out, and put in 1 at a time, and it
    > > worked perfectly.


    Looks like you have a hardware issue, perhaps low voltage on the ports
    that cause them to be disconnected at the electrical USB level, which is
    nothing that we can do about within the kernel.

    thanks,

    greg k-h
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

+ Reply to Thread