Am 2008-10-01 01:47 +0900 schrieb Tejun Heo:
> Please apply the attached patch and see whether the problem goes
> away.

I will take care of this this evening.

> Also, can you test whether hotplug works with the patch applied?

Erm... I never did Hotplug on SATA, should I plug out the Disk out of
the Mainboard Connector to see what happens? I suspect I need another
additional disk the or a live-usb linux with this Kernel...

> Thanks.

Thats no problem, but one question:

Should this

> diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
> index 14601dc..18f81d2 100644
> +++ b/drivers/ata/sata_nv.c
> @@ -433,6 +433,7 @@ static struct ata_port_operations nv_nf2_ops = {
> .inherits = &nv_common_ops,
> .freeze = nv_nf2_freeze,
> .thaw = nv_nf2_thaw,
> + .hardreset = ATA_OP_NULL,
> };
>
> static struct ata_port_operations nv_ck804_ops = {

go onto vanilla 2.6.27_rc7 WITH or withOUT
sata_nv-reinstate-nv_hardreset.patch?


Regards, Konsti


--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Konstantin Kletschke wrote:
> Am 2008-10-01 01:47 +0900 schrieb Tejun Heo:
>> Please apply the attached patch and see whether the problem goes
>> away.
>
> I will take care of this this evening.
>
>> Also, can you test whether hotplug works with the patch applied?
>
> Erm... I never did Hotplug on SATA, should I plug out the Disk out of
> the Mainboard Connector to see what happens? I suspect I need another
> additional disk the or a live-usb linux with this Kernel...

Or you can boot into single mode, ro mount / with kernel messages
redirected to console and hot unplug/plug the root disk and see what
happens.

> Should this
>
>> diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
>> index 14601dc..18f81d2 100644
>> +++ b/drivers/ata/sata_nv.c
>> @@ -433,6 +433,7 @@ static struct ata_port_operations nv_nf2_ops = {
>> .inherits = &nv_common_ops,
>> .freeze = nv_nf2_freeze,
>> .thaw = nv_nf2_thaw,
>> + .hardreset = ATA_OP_NULL,
>> };
>>
>> static struct ata_port_operations nv_ck804_ops = {
>
> go onto vanilla 2.6.27_rc7 WITH or withOUT
> sata_nv-reinstate-nv_hardreset.patch?

With.

Thanks.

--
tejun
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Well, this way the Situation is the following:

TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 2008
io scheduler noop registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
Linux agpgart interface v0.103
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
forcedeth 0000:00:05.0: PCI INT A -> Link[LKLN] -> GSI 22 (level, low) -> IRQ 22
forcedeth 0000:00:05.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
Switched to high resolution mode on CPU 0
forcedeth 0000:00:05.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:13:8f:fd:f9:26
forcedeth 0000:00:05.0: csum timirq lnktim desc-v2
netconsole: local port 6665
netconsole: local IP 10.10.0.1
netconsole: interface eth0
netconsole: remote port 6666
netconsole: remote IP 10.10.0.18
netconsole: remote ethernet address 00:22:15:68:2c:eb
netconsole: device eth0 not up yet, forcing it
eth0: no link during initialization.
eth0: link up.
console [netcon0] enabled
netconsole: network logging started
Driver 'sd' needs updating - please use bus_type methods
sata_nv 0000:00:0a.0: version 3.5
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
sata_nv 0000:00:0a.0: PCI INT A -> Link[LTID] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0a.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xf80 ctl 0xf00 bmdma 0xd800 irq 21
ata2: SATA max UDMA/133 cmd 0xe80 ctl 0xe00 bmdma 0xd808 irq 21
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
isa bounce pool size: 16 pages
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 17
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 220k freed

Then this continues:

ata2: EH pending after 5 tries, giving up
ata2: EH complete
ata2: EH pending after 5 tries, giving up
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete


Rebooting is not possible (seldom it is possible though), most often it
yields into the BIOS not recognizing the disk after the reset anymore.
The shutdown (the system is headless regularly and I wait for hearing the
BIOS beep) lasts very long (before it waits for the disk or finds no OS).

Sadly I have no time to put a monitor onto it, if further investigations
are required I can take care of this friday.

Kind Regards and happy hacking, Konsti


--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

On Sep. 24, 2008, 12:36 +0300, Tejun Heo wrote:
> Please apply the attached patch and post the resulting log. Please
> don't forget to turn on KALLSYMS.
>
> Thanks.
>

With commit 4c1eb90a0908c0c60db2169dce08fb672e7582f1 (v2.6.27-rc8),
I see no spurious EH complete events as I saw with 2.6.27-rc <= 7.

Thanks,

Benny
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Benny Halevy wrote:
> On Sep. 24, 2008, 12:36 +0300, Tejun Heo wrote:
>> Please apply the attached patch and post the resulting log. Please
>> don't forget to turn on KALLSYMS.
>>
>> Thanks.
>>
>
> With commit 4c1eb90a0908c0c60db2169dce08fb672e7582f1 (v2.6.27-rc8),
> I see no spurious EH complete events as I saw with 2.6.27-rc <= 7.

You're on CK804, right?

--
tejun
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

On Oct. 05, 2008, 12:18 +0200, Tejun Heo wrote:
> Benny Halevy wrote:
>> On Sep. 24, 2008, 12:36 +0300, Tejun Heo wrote:
>>> Please apply the attached patch and post the resulting log. Please
>>> don't forget to turn on KALLSYMS.
>>>
>>> Thanks.
>>>
>> With commit 4c1eb90a0908c0c60db2169dce08fb672e7582f1 (v2.6.27-rc8),
>> I see no spurious EH complete events as I saw with 2.6.27-rc <= 7.
>
> You're on CK804, right?
>

No, MCP55 actually:

$ lspci | grep IDE
00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Benny Halevy wrote:
> On Oct. 05, 2008, 12:18 +0200, Tejun Heo wrote:
>> Benny Halevy wrote:
>>> On Sep. 24, 2008, 12:36 +0300, Tejun Heo wrote:
>>>> Please apply the attached patch and post the resulting log. Please
>>>> don't forget to turn on KALLSYMS.
>>>>
>>>> Thanks.
>>>>
>>> With commit 4c1eb90a0908c0c60db2169dce08fb672e7582f1 (v2.6.27-rc8),
>>> I see no spurious EH complete events as I saw with 2.6.27-rc <= 7.
>> You're on CK804, right?
>>
>
> No, MCP55 actually:
>
> $ lspci | grep IDE
> 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
> 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
> 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)

Right, the commit fixes generic and CK804 while break nf2/3. Can you
also try the following patch?

http://article.gmane.org/gmane.linux.ide/34942/raw

--
tejun
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

On Oct. 05, 2008, 12:42 +0200, Tejun Heo wrote:
> Benny Halevy wrote:
>> On Oct. 05, 2008, 12:18 +0200, Tejun Heo wrote:
>>> Benny Halevy wrote:
>>>> On Sep. 24, 2008, 12:36 +0300, Tejun Heo wrote:
>>>>> Please apply the attached patch and post the resulting log. Please
>>>>> don't forget to turn on KALLSYMS.
>>>>>
>>>>> Thanks.
>>>>>
>>>> With commit 4c1eb90a0908c0c60db2169dce08fb672e7582f1 (v2.6.27-rc8),
>>>> I see no spurious EH complete events as I saw with 2.6.27-rc <= 7.
>>> You're on CK804, right?
>>>
>> No, MCP55 actually:
>>
>> $ lspci | grep IDE
>> 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
>> 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
>> 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
>
> Right, the commit fixes generic and CK804 while break nf2/3. Can you
> also try the following patch?
>
> http://article.gmane.org/gmane.linux.ide/34942/raw
>

Log looks clean with this patch as well.

Benny
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Am 2008-10-05 19:42 +0900 schrieb Tejun Heo:

> Right, the commit fixes generic and CK804 while break nf2/3. Can you
> also try the following patch?
>
> http://article.gmane.org/gmane.linux.ide/34942/raw

Hm, sadly doesn't look so well:

Linux version 2.6.27-rc8 (root@zappa) (gcc version 4.3.1 (Gentoo 4.3.1-r1 p
2 CEST 2008
Command line: auto BOOT_IMAGE=linux ro root=801 netconsole=6665@10.10.0.1/e
5:68:2c:eb loglevel=8 debug
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data)
BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
last_pfn = 0x3ffb0 max_arch_pfn = 0x3ffffffff
init_memory_mapping
0000000000 - 003fe00000 page 2M
003fe00000 - 003ffb0000 page 4k
kernel direct mapping tables up to 3ffb0000 @ 8000-b000
last_map_addr: 3ffb0000 end: 3ffb0000
DMI 2.3 present.
ACPI: RSDP 000F8710, 0014 (r0 ACPIAM)
ACPI: RSDT 3FFB0000, 0030 (r1 A M I OEMRSDT 8000607 MSFT 97)
ACPI: FACP 3FFB0200, 0084 (r2 A M I OEMFACP 8000607 MSFT 97)
ACPI: DSDT 3FFB03F0, 3F26 (r1 K8UNF K8UNF201 201 INTL 2002026)
ACPI: FACS 3FFC0000, 0040
ACPI: APIC 3FFB0390, 005C (r1 A M I OEMAPIC 8000607 MSFT 97)
ACPI: OEMB 3FFC0040, 0056 (r1 A M I AMI_OEM 8000607 MSFT 97)
(4 early reservations) ==> bootmem [0000000000 - 003ffb0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 000000100
#1 [0000200000 - 000058a730] TEXT DATA BSS ==> [0000200000 - 000058a73
#2 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 000010000
#3 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 000000900
[ffffe20000000000-ffffe20000dfffff] PMD -> [ffff880001200000-ffff880001fff
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0003ffb0
On node 0 totalpages: 261967
DMA zone: 2939 pages, LIFO batch:0
DMA32 zone: 254441 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bf7c0000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257380
Kernel command line: auto BOOT_IMAGE=linux ro root=801 netconsole=6665@10.1
00:22:15:68:2c:eb loglevel=8 debug
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 1607.798 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
AGP bridge at 00:00:00
Aperture from AGP @ f8000000 old size 32 MB
Aperture size 4096 MB (APSIZE 0) is not right, using settings from NB
Aperture from AGP @ f8000000 size 32 MB (APSIZE 0)
Node 0: aperture @ 94f8000000 size 64 MB
Aperture beyond 4GB. Ignoring.
Memory: 1027656k/1048256k available (2338k kernel code, 19716k reserved, 81
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay loop (skipped), value calculated using timer frequency..
92)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
tseg: 0000000000
CPU: AMD Sempron(tm) Processor 2800+ stepping 02
ACPI: Core revision 20080609
...TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
Using local APIC timer interrupts.
APIC timer calibration result 12560917
Detected 12.560 MHz APIC timer.
net_namespace: 1136 bytes
NET: Registered protocol family 16
No dock devices found.
node 0 link 0: io port [1000, ffffff]
TOM: 0000000040000000 aka 1024M
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [40000000, fe0bffff]
bus: [00,ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [a0000, bffff]
bus: 00 index 2 mmio: [40000000, fcffffffff]
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:00.0 reg 10 32bit mmio: [f8000000, fbffffff]
PCI: 0000:00:01.1 reg 10 io port: [5080, 509f]
PCI: 0000:00:01.1 reg 20 io port: [5000, 503f]
PCI: 0000:00:01.1 reg 24 io port: [5040, 507f]
pci 0000:00:01.1: PME# supported from D3hot D3cold
pci 0000:00:01.1: PME# disabled
PCI: 0000:00:02.0 reg 10 32bit mmio: [febff000, febfffff]
pci 0000:00:02.0: supports D1
pci 0000:00:02.0: supports D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
PCI: 0000:00:02.1 reg 10 32bit mmio: [febfe000, febfefff]
pci 0000:00:02.1: supports D1
pci 0000:00:02.1: supports D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
PCI: 0000:00:02.2 reg 10 32bit mmio: [febfdc00, febfdcff]
pci 0000:00:02.2: supports D1
pci 0000:00:02.2: supports D2
pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.2: PME# disabled
PCI: 0000:00:05.0 reg 10 32bit mmio: [febfc000, febfcfff]
PCI: 0000:00:05.0 reg 14 io port: [ec00, ec07]
pci 0000:00:05.0: supports D1
pci 0000:00:05.0: supports D2
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
PCI: 0000:00:06.0 reg 10 io port: [e800, e8ff]
PCI: 0000:00:06.0 reg 14 io port: [e480, e4ff]
PCI: 0000:00:06.0 reg 18 32bit mmio: [febfb000, febfbfff]
pci 0000:00:06.0: supports D1
pci 0000:00:06.0: supports D2
PCI: 0000:00:08.0 reg 20 io port: [ffa0, ffaf]
PCI: 0000:00:0a.0 reg 10 io port: [f80, f87]
PCI: 0000:00:0a.0 reg 14 io port: [f00, f03]
PCI: 0000:00:0a.0 reg 18 io port: [e80, e87]
PCI: 0000:00:0a.0 reg 1c io port: [e00, e03]
PCI: 0000:00:0a.0 reg 20 io port: [d800, d80f]
PCI: 0000:00:0a.0 reg 24 io port: [d400, d47f]
PCI: 0000:01:00.0 reg 10 32bit mmio: [fd000000, fdffffff]
PCI: 0000:01:00.0 reg 14 32bit mmio: [e8000000, efffffff]
PCI: 0000:01:00.0 reg 30 32bit mmio: [fe9e0000, fe9fffff]
PCI: bridge 0000:00:0b.0 32bit mmio: [fc900000, fe9fffff]
PCI: bridge 0000:00:0b.0 32bit mmio pref: [e4800000, f47fffff]
PCI: 0000:02:06.0 reg 10 io port: [c800, c8ff]
PCI: 0000:02:06.0 reg 14 32bit mmio: [feaffc00, feaffcff]
PCI: 0000:02:06.0 reg 30 32bit mmio: [fffe0000, ffffffff]
pci 0000:02:06.0: supports D1
pci 0000:02:06.0: supports D2
pci 0000:02:06.0: PME# supported from D1 D2 D3hot
pci 0000:02:06.0: PME# disabled
PCI: bridge 0000:00:0e.0 io port: [c000, cfff]
PCI: bridge 0000:00:0e.0 32bit mmio: [fea00000, feafffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *9
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 22) *14
ACPI: Power Resource [ISAV] (on)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - E0, shoul
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
agpgart-amd64 0000:00:00.0: AGP bridge [10de/00e1]
agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP
agpgart-amd64 0000:00:00.0: AGP aperture is 32M @ 0xf8000000
ACPI: RTC can wake from S4
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x4000-0x407f has been reserved
system 00:09: ioport range 0x4080-0x40ff has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfeefffff has been reserved
system 00:0a: iomem range 0xff7c0000-0xffffffff could not be reserved
system 00:0c: ioport range 0x290-0x29f has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xcffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x3fffffff could not be reserved
pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0b.0: IO window: disabled
pci 0000:00:0b.0: MEM window: 0xfc900000-0xfe9fffff
pci 0000:00:0b.0: PREFETCH window: 0x000000e4800000-0x000000f47fffff
pci 0000:00:0e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:0e.0: IO window: 0xc000-0xcfff
pci 0000:00:0e.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:0e.0: PREFETCH window: 0x00000050000000-0x000000500fffff
pci 0000:00:0e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 mmio: [0, 0]
bus: 01 index 1 mmio: [fc900000, fe9fffff]
bus: 01 index 2 mmio: [e4800000, f47fffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [c000, cfff]
bus: 02 index 1 mmio: [fea00000, feafffff]
bus: 02 index 2 mmio: [50000000, 500fffff]
bus: 02 index 3 mmio: [0, 0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers
SGI XFS Quota Management subsystem
msgmni has been set to 2008
io scheduler noop registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
Linux agpgart interface v0.103
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
forcedeth 0000:00:05.0: PCI INT A -> Link[LKLN] -> GSI 22 (level, low) -> I
forcedeth 0000:00:05.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
Switched to high resolution mode on CPU 0
forcedeth 0000:00:05.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:13:8f:fd:f9
forcedeth 0000:00:05.0: csum timirq lnktim desc-v2
netconsole: local port 6665
netconsole: local IP 10.10.0.1
netconsole: interface eth0
netconsole: remote port 6666
netconsole: remote IP 10.10.0.18
netconsole: remote ethernet address 00:22:15:68:2c:eb
netconsole: device eth0 not up yet, forcing it
eth0: no link during initialization.
eth0: link up.
console [netcon0] enabled
netconsole: network logging started
Driver 'sd' needs updating - please use bus_type methods
sata_nv 0000:00:0a.0: version 3.5
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
sata_nv 0000:00:0a.0: PCI INT A -> Link[LTID] -> GSI 21 (level, low) -> IRQ
sata_nv 0000:00:0a.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xf80 ctl 0xf00 bmdma 0xd800 irq 21
ata2: SATA max UDMA/133 cmd 0xe80 ctl 0xe00 bmdma 0xd808 irq 21
ata1: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: link online but device misclassified, retrying
ata1: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: link online but device misclassified, retrying
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
isa bounce pool size: 16 pages
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI:
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't suppor
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't suppor
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 17
XFS mounting filesystem sda1
Starting XFS recovery on filesystem: sda1 (logdev: internal)
Ending XFS recovery on filesystem: sda1 (logdev: internal)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
processor ACPI0007:00: registered as cooling_device0
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input
ACPI: Power Button (CM) [PWRB]
parport_pc 00:06: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EP
parport0: Printer, Kyocera Mita FS-1000+
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 20 (level, low) -> IR
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 20, io mem 0xfebff000
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 22
ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 22 (level, low) -> IR
ohci_hcd 0000:00:02.1: setting latency timer to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 22, io mem 0xfebfe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 21 (level, low) -> IR
ehci_hcd 0000:00:02.2: setting latency timer to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: debug port 0
ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
ehci_hcd 0000:00:02.2: irq 21, io mem 0xfebfdc00
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
pata_amd 0000:00:08.0: version 0.3.10
pata_amd 0000:00:08.0: power state changed by ACPI to D0
pata_amd 0000:00:08.0: setting latency timer to 64
scsi2 : pata_amd
scsi3 : pata_amd
ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata4.00: ATAPI: HL-DT-ST CD-ROM GCR-8520B, 1.00, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0x0) ACPI=0x39f (120:60
ata4.00: configured for MWDMA2
scsi 3:0:0:0: CD-ROM HL-DT-ST CD-ROM GCR-8520B 1.00 PQ: 0 ANSI:
scsi 3:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
8139too 0000:02:06.0: PCI INT A -> Link[LNKC] -> GSI 19 (level, low) -> IRQ
eth1: RealTek RTL8139 at 0xffffc20000066c00, 00:a1:b0:f0:2b:d1, IRQ 19
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
usb 2-2: new full speed USB device using ohci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0
usbcore: registered new interface driver usblp
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
lp0: using parport0 (interrupt-driven).
XFS mounting filesystem sda3
Ending clean XFS mount for filesystem: sda3
XFS mounting filesystem sda5
Ending clean XFS mount for filesystem: sda5
XFS mounting filesystem sda9
Ending clean XFS mount for filesystem: sda9
XFS mounting filesystem sda7
Starting XFS recovery on filesystem: sda7 (logdev: internal)
Ending XFS recovery on filesystem: sda7 (logdev: internal)
kjournald2 starting. Commit interval 5 seconds
EXT4 FS on sda6, internal journal
EXT4-fs: mounted filesystem with journal data mode.
EXT4-fs: Ignoring delalloc option - requested data journaling mode
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
XFS mounting filesystem sda8
Ending clean XFS mount for filesystem: sda8
Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k
PPP generic driver version 2.4.2
NET: Registered protocol family 24
eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period

May be my engine has a problem with the disk itself additionaly?

ata1: link online but device misclassified, retrying

Regards, Konsti



--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

What I forgot is, that the

ata2: EH pending after 5 tries, giving up
ata2: EH complete
ata2: EH pending after 5 tries, giving up
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete
ata2: EH complete

is away now and tomorrow morning I will take care if it
manages to do a cold boot after it was switched of this night.

--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Konstantin Kletschke wrote:
> What I forgot is, that the
>
> ata2: EH pending after 5 tries, giving up
> ata2: EH complete
> ata2: EH pending after 5 tries, giving up
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
> ata2: EH complete
>
> is away now and tomorrow morning I will take care if it
> manages to do a cold boot after it was switched of this night.
>

Hmm... strange. Can you please try the attached patch? It's basically
the same with a bit more debug information.

Thanks.

--
tejun

Am 2008-10-07 10:02 +0900 schrieb Tejun Heo:

> Hmm... strange. Can you please try the attached patch? It's basically
> the same with a bit more debug information.

No Problem.

I had difficulties to cold boot the machine today, I had to powercycle a
lot. Then I applied the patch and it bootet immediately:

sata_nv 0000:00:0a.0: version 3.5
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
sata_nv 0000:00:0a.0: PCI INT A -> Link[LTID] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0a.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xf80 ctl 0xf00 bmdma 0xd800 irq 21
ata2: SATA max UDMA/133 cmd 0xe80 ctl 0xe00 bmdma 0xd808 irq 21
ata1: hard resetting link
XXX CLASSIFY 01:00:00
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata1: EH complete
ata2: hard resetting link
ata2: SATA link down (SStatus 0 SControl 300)
ata2: EH complete
isa bounce pool size: 16 pages
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 17
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 220k freed


Then I switched off and smoked a cigarette, booting then lasted a bit longer:

ata1: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: link online but device misclassified, retrying
ata1: hard resetting link
ata1: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: link online but device misclassified, retrying
ata1: hard resetting link
XXX CLASSIFY 01:00:00
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata1: EH complete
ata2: hard resetting link
ata2: SATA link down (SStatus 0 SControl 300)
ata2: EH complete
isa bounce pool size: 16 pages
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 17
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 220k freed


Konsti

--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

On Oct. 07, 2008, 8:04 +0200, Konstantin Kletschke wrote:
> Am 2008-10-07 10:02 +0900 schrieb Tejun Heo:
>
>> Hmm... strange. Can you please try the attached patch? It's basically
>> the same with a bit more debug information.
>
> No Problem.
>
> I had difficulties to cold boot the machine today, I had to powercycle a
> lot. Then I applied the patch and it bootet immediately:
>
> sata_nv 0000:00:0a.0: version 3.5
> ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
> sata_nv 0000:00:0a.0: PCI INT A -> Link[LTID] -> GSI 21 (level, low) -> IRQ 21
> sata_nv 0000:00:0a.0: setting latency timer to 64
> scsi0 : sata_nv
> scsi1 : sata_nv
> ata1: SATA max UDMA/133 cmd 0xf80 ctl 0xf00 bmdma 0xd800 irq 21
> ata2: SATA max UDMA/133 cmd 0xe80 ctl 0xe00 bmdma 0xd808 irq 21
> ata1: hard resetting link
> XXX CLASSIFY 01:00:00
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
> ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
> ata1.00: configured for UDMA/133
> ata1: EH complete
> ata2: hard resetting link
> ata2: SATA link down (SStatus 0 SControl 300)
> ata2: EH complete
> isa bounce pool size: 16 pages
> scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
> sd 0:0:0:0: [sda] Attached SCSI disk
> PNP: No PS/2 controller found. Probing ports directly.
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> TCP cubic registered
> NET: Registered protocol family 17
> XFS mounting filesystem sda1
> Ending clean XFS mount for filesystem: sda1
> VFS: Mounted root (xfs filesystem) readonly.
> Freeing unused kernel memory: 220k freed
>
>
> Then I switched off and smoked a cigarette, booting then lasted a bit longer:

See, cigarettes are bad for you(r computer) ;-)

Benny

>
> ata1: link is slow to respond, please be patient (ready=0)
> ata1: SRST failed (errno=-16)
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1: link online but device misclassified, retrying
> ata1: hard resetting link
> ata1: link is slow to respond, please be patient (ready=0)
> ata1: SRST failed (errno=-16)
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1: link online but device misclassified, retrying
> ata1: hard resetting link
> XXX CLASSIFY 01:00:00
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
> ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
> ata1.00: configured for UDMA/133
> ata1: EH complete
> ata2: hard resetting link
> ata2: SATA link down (SStatus 0 SControl 300)
> ata2: EH complete
> isa bounce pool size: 16 pages
> scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
> sd 0:0:0:0: [sda] Attached SCSI disk
> PNP: No PS/2 controller found. Probing ports directly.
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> TCP cubic registered
> NET: Registered protocol family 17
> XFS mounting filesystem sda1
> Ending clean XFS mount for filesystem: sda1
> VFS: Mounted root (xfs filesystem) readonly.
> Freeing unused kernel memory: 220k freed
>
>
> Konsti
>

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Am 2008-10-07 10:10 +0200 schrieb Benny Halevy:

> > Then I switched off and smoked a cigarette, booting then lasted a bit longer:
>
> See, cigarettes are bad for you(r computer) ;-)

Yes... But where does he know from? I have no /dev/eyes still ;-)

--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Konstantin Kletschke wrote:
> Am 2008-10-07 10:10 +0200 schrieb Benny Halevy:
>
>>> Then I switched off and smoked a cigarette, booting then lasted a bit longer:
>> See, cigarettes are bad for you(r computer) ;-)
>
> Yes... But where does he know from? I have no /dev/eyes still ;-)
>

It has all the fans for a reason. :-)

Eh... Joke aside. I still don't know what's going on here. Before
2.6.26, you always had clean boot, right?

--
tejun
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Tejun Heo wrote:
> Konstantin Kletschke wrote:
>> Am 2008-10-07 10:10 +0200 schrieb Benny Halevy:
>>
>>>> Then I switched off and smoked a cigarette, booting then lasted a bit longer:
>>> See, cigarettes are bad for you(r computer) ;-)
>> Yes... But where does he know from? I have no /dev/eyes still ;-)
>>
>
> It has all the fans for a reason. :-)
>
> Eh... Joke aside. I still don't know what's going on here. Before
> 2.6.26, you always had clean boot, right?

Also, can you please repeat the test several times and see whether there
are some patterns? And please also try pre-2.6.26 kernel a few times
just to make sure it's not some bad coincidence.

Thanks.

--
tejun
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Am 2008-10-13 17:36 +0900 schrieb Tejun Heo:

> It has all the fans for a reason. :-)

:-)

> Eh... Joke aside. I still don't know what's going on here. Before
> 2.6.26, you always had clean boot, right?

Yes, with 2.6.25 it always had a clean booting system.

From time to time I do an update and with some 2.6.26_rcX I had
problems the system not solving a cold boot sometimes. Long I suspected
a hardware issue but one time I went down to 2.6.25 and the problem was
away.

Then I updated to 2.6.27_rcX because I was hunting down some nfsv4
error, considering this as a bug or an issue in front of screen. Then I
realised the cold boot problem again which I almost forgot meanwhile or
considered closed from 2.6.26_rcX over 2.6.26 to 2.6.27_rcX.

Konsti

--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Am 2008-10-13 17:38 +0900 schrieb Tejun Heo:

> Also, can you please repeat the test several times and see whether there

Still I have the last suggested patch running and the machine solves to
boot cold any time (I am shure meanwhile, turned off the whole sunday it
botted this morning and so on - any time).

Consistent is this issue telling something about MISSCLASSIFIED:

sata_nv 0000:00:0a.0: version 3.5
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
sata_nv 0000:00:0a.0: PCI INT A -> Link[LTID] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0a.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xf80 ctl 0xf00 bmdma 0xd800 irq 21
ata2: SATA max UDMA/133 cmd 0xe80 ctl 0xe00 bmdma 0xd808 irq 21
ata1: hard resetting link
ata1: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: link online but device misclassified, retrying
ata1: hard resetting link
ata1: link is slow to respond, please be patient (ready=0)
ata1: SRST failed (errno=-16)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: link online but device misclassified, retrying
ata1: hard resetting link
XXX CLASSIFY 01:00:00
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata1: EH complete
ata2: hard resetting link
ata2: SATA link down (SStatus 0 SControl 300)
ata2: EH complete
isa bounce pool size: 16 pages
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk

It struggles a bit then (a couple of seconds?), but solves to boot.

> are some patterns? And please also try pre-2.6.26 kernel a few times

This is consitent now.

> just to make sure it's not some bad coincidence.

I will check this out but need to look if this is possible with my nfsv4
issues then, I will report.

Konsti


--
GPG KeyID EF62FCEF
Fingerprint: 13C9 B16B 9844 EC15 CC2E A080 1E69 3FDA EF62 FCEF
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Hmm... this is proving to be much more difficult than I expected. :-(

Can you please try the attached patch?

Thanks.

--
tejun