nvidia MCP78B ahci failed to IDENTIFY error on 2.6.26 - Kernel

This is a discussion on nvidia MCP78B ahci failed to IDENTIFY error on 2.6.26 - Kernel ; Hi, I get the follwing errors when booting 2.6.26 on a FSC Esprimo P5625 (nvidia MCP78B). ------------[ cut here ]------------ WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100 [libata]() Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+) ata_generic tpm_infineon tpm tpm_bios pata_acpi libata ...

+ Reply to Thread
Results 1 to 7 of 7

Thread: nvidia MCP78B ahci failed to IDENTIFY error on 2.6.26

  1. nvidia MCP78B ahci failed to IDENTIFY error on 2.6.26

    Hi,

    I get the follwing errors when booting 2.6.26 on a FSC Esprimo P5625 (nvidia
    MCP78B).

    ------------[ cut here ]------------
    WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100
    [libata]()
    Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+)
    ata_generic tpm_infineon tpm tpm_bios pata_acpi libata shpchp dock
    pci_hotplug ehci_hcd ohci_hcd usbcore container thermal button processor
    evdev
    Pid: 1937, comm: modprobe Not tainted 2.6.26 #1
    [] warn_on_slowpath+0x5f/0x90
    [] finish_task_switch+0x95/0xa0
    [] dma_alloc_coherent+0x122/0x2b0
    [] devres_add+0x31/0x50
    [] dmam_alloc_coherent+0x6c/0x90
    [] ahci_port_resume+0x5f/0x70 [ahci]
    [] devres_add+0x31/0x50
    [] ata_host_start+0xed/0x170 [libata]
    [] pci_bus_write_config_byte+0x5a/0x70
    [] ata_host_activate+0xf6/0x100 [libata]
    [] ahci_init_one+0x899/0xac0 [ahci]
    [] pci_device_probe+0x56/0x80
    [] driver_probe_device+0x82/0x180
    [] __driver_attach+0x6c/0x70
    [] bus_for_each_dev+0x3b/0x60
    [] driver_attach+0x16/0x20
    [] __driver_attach+0x0/0x70
    [] bus_add_driver+0xa9/0x210
    [] pci_device_remove+0x0/0x40
    [] driver_register+0x4d/0x120
    [] __pci_register_driver+0x3d/0x80
    [] sys_init_module+0x84/0x1b0
    [] sysenter_past_esp+0x6a/0x99
    =======================
    ---[ end trace 21da9b6136ad63e5 ]---

    The serial ata harddisk does not appear.

    ---------[ lspci -n ]---------
    00:00.0 0500: 10de:0754 (rev a2)
    00:01.0 0601: 10de:075c (rev a2)
    00:01.1 0c05: 10de:0752 (rev a1)
    00:01.2 0500: 10de:0751 (rev a1)
    00:01.4 0500: 10de:0568 (rev a1)
    00:02.0 0c03: 10de:077b (rev a1)
    00:02.1 0c03: 10de:077c (rev a1)
    00:04.0 0c03: 10de:077d (rev a1)
    00:04.1 0c03: 10de:077e (rev a1)
    00:07.0 0403: 10de:0774 (rev a1)
    00:08.0 0604: 10de:075a (rev a1)
    00:09.0 0101: 10de:0ad0 (rev a2)
    00:0b.0 0604: 10de:0569 (rev a1)
    00:10.0 0604: 10de:0778 (rev a1)
    00:12.0 0604: 10de:075b (rev a1)
    00:13.0 0604: 10de:077a (rev a1)
    00:18.0 0600: 1022:1100
    00:18.1 0600: 1022:1101
    00:18.2 0600: 1022:1102
    00:18.3 0600: 1022:1103
    02:00.0 0300: 10de:084b (rev a2)
    05:00.0 0200: 14e4:169b (rev 02)
    ----------------------------------

    Full dmesg output:

    Linux version 2.6.26 (root@pcbon14) (gcc version 4.2.3 (Ubuntu
    4.2.3-2ubuntu7)) #1 SMP PREEMPT Mon Jul 21 16:44:03 UTC 2008
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
    BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 0000000037f40000 (usable)
    BIOS-e820: 0000000037f40000 - 0000000037f4d000 (ACPI data)
    BIOS-e820: 0000000037f4d000 - 0000000037f4e000 (ACPI NVS)
    BIOS-e820: 0000000037f4e000 - 0000000040000000 (reserved)
    BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    895MB LOWMEM available.
    found SMP MP-table at [c00f75e0] 000f75e0
    Entering add_active_range(0, 0, 229184) 0 entries of 256 used
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 229184
    HighMem 229184 -> 229184
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
    0: 0 -> 229184
    On node 0 totalpages: 229184
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 4064 pages, LIFO batch:0
    Normal zone: 1759 pages used for memmap
    Normal zone: 223329 pages, LIFO batch:31
    HighMem zone: 0 pages used for memmap
    Movable zone: 0 pages used for memmap
    DMI present.
    ACPI: RSDP 000F75B0, 0024 (r2 PTLTD )
    ACPI: XSDT 37F45097, 007C (r1 FSC PC 60000 LTP 0)
    ACPI: FACP 37F4C7FA, 00F4 (r3 FSC 60000 PTL_ F4240)
    ACPI: DSDT 37F45113, 7673 (r1 FSC D2721/A1 60000 MSFT 3000001)
    ACPI: FACS 37F4DFC0, 0040
    ACPI: TCPA 37F4C8EE, 0032 (r1 Phoeni x 60000 TL 0)
    ACPI: WDAT 37F4C920, 0104 (r1 PTLTD WDATTBL 60000 LTP 1)
    ACPI: SSDT 37F4CA24, 0248 (r1 AMD POWERNOW 60000 AMD 1)
    ACPI: SRAT 37F4CC6C, 00A0 (r1 AMD HAMMER 60000 AMD 1)
    ACPI: ASF! 37F4CD0C, 0070 (r32 OEMID OEMTBL 60000 PTL 1)
    ACPI: SLIC 37F4CD7C, 0176 (r1 FSC PC 60000 LTP 0)
    ACPI: MCFG 37F4CEF2, 003C (r1 PTLTD MCFG 60000 LTP 0)
    ACPI: HPET 37F4CF2E, 0038 (r1 PTLTD HPETTBL 60000 LTP 1)
    ACPI: APIC 37F4CF66, 0072 (r1 PTLTD APIC 60000 LTP 0)
    ACPI: BOOT 37F4CFD8, 0028 (r1 PTLTD $SBFTBL$ 60000 LTP 1)
    ACPI: DMI detected: Fujitsu Siemens
    Detected use of extended apic ids on hypertransport bus
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    ACPI: HPET id: 0x10de8201 base: 0xfed00000
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 50000000 (gap: 40000000:b8000000)
    SMP: Allowing 2 CPUs, 0 hotplug CPUs
    PERCPU: Allocating 36392 bytes of per cpu data
    NR_CPUS: 32, nr_cpu_ids: 2
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227393
    Kernel command line: lang=de video=vesa:ywrap,mtrr
    pckey=4e6842c5129e7882c318378dde52fe2e service=192.168.1.14 vga=791
    initrd=miniroot.gz reboot=b product=winxppro init=/etc/init quiet hn=evb
    ramdisk_size=185320 splash BOOT_IMAGE=install
    mapped APIC to ffffb000 (fee00000)
    mapped IOAPIC to ffffa000 (fec00000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 16384 bytes)
    Extended CMOS year: 2000
    Detected 2300.065 MHz processor.
    spurious 8259A interrupt: IRQ7.
    Console: colour dummy device 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 841640k/916736k available (2127k kernel code, 74572k reserved, 758k
    data, 340k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xffe14000 - 0xfffff000 (1964 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
    lowmem : 0xc0000000 - 0xf7f40000 ( 895 MB)
    .init : 0xc03d7000 - 0xc042c000 ( 340 kB)
    .data : 0xc0313e37 - 0xc03d1a20 ( 758 kB)
    .text : 0xc0100000 - 0xc0313e37 (2127 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    CPA: page pool initialized 1 of 1 pages preallocated
    hpet clockevent registered
    Calibrating delay using timer specific routine.. 4605.32 BogoMIPS
    (lpj=9210650)
    Mount-cache hash table entries: 512
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU 0(2) -> Core 0
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    ACPI: Core revision 20080321
    ENABLING IO-APIC IRQs
    ...TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
    CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02
    APIC calibration not consistent with PM Timer: 349ms instead of 100ms
    APIC delta adjusted to PM-Timer: 357954 (1249981)
    Booting processor 1/1 ip 6000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 1317.37 BogoMIPS
    (lpj=2634740)
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU 1(2) -> Core 1
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02
    Brought up 2 CPUs
    Total of 2 processors activated (5922.69 BogoMIPS).
    CPU0 attaching sched-domain:
    domain 0: span 0-1
    groups: 0 1
    CPU1 attaching sched-domain:
    domain 0: span 0-1
    groups: 1 0
    net_namespace: 200 bytes
    NET: Registered protocol family 16
    EISA bus registered
    ACPI: bus type pci registered
    PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 5
    PCI: MCFG area at f8000000 reserved in E820
    PCI: Using MMCONFIG for extended config space
    PCI: Using configuration type 1 for base access
    Setting up standard PCI resources
    ACPI: EC: Look up EC in DSDT
    ACPI: Interpreter enabled
    ACPI: (supports S0 S1 S3 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: Device [ECP] status [00000008]: functional but not present; setting
    present
    ACPI: Device [COM2] status [00000008]: functional but not present; setting
    present
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Transparent bridge - 0000:00:08.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXA._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXB._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXL._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LK0A] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LK0B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK0C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK0D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK1A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK1B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK1C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK1D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK2A] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LK2B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK2C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK2D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK3A] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LK3B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK3C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK3D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK4A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK4B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK4C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK4D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK5A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK5B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK5C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK5D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK6A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK6B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK6C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK6D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK7A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK7B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK7C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LK7D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR0] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR2] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR3] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR4] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR5] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR6] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LKR7] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *5
    ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *10
    ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LNKQ] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LNKR] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LNKS] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LNKT] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 15 devices
    ACPI: ACPI bus type pnp unregistered
    PnPBIOS: Disabled by ACPI PNP
    SCSI subsystem initialized
    PCI: Using ACPI for IRQ routing
    ACPI: RTC can wake from S4
    system 00:01: ioport range 0x4d0-0x4d1 has been reserved
    system 00:01: ioport range 0x500-0x57f has been reserved
    system 00:01: ioport range 0x1000-0x10e7 has been reserved
    system 00:01: ioport range 0x1200-0x12fe has been reserved
    system 00:01: ioport range 0x1400-0x14fe has been reserved
    system 00:01: ioport range 0x1500-0x15fe has been reserved
    system 00:01: ioport range 0x1600-0x16fe has been reserved
    system 00:01: ioport range 0x1700-0x17fe has been reserved
    system 00:01: ioport range 0x1800-0x18fe has been reserved
    system 00:01: ioport range 0x1900-0x19fe has been reserved
    system 00:01: ioport range 0x1a00-0x1afe has been reserved
    system 00:01: ioport range 0x1c00-0x1cfe has been reserved
    system 00:01: ioport range 0xfe00-0xfe00 has been reserved
    system 00:01: ioport range 0xff00-0xff00 has been reserved
    system 00:01: iomem range 0xf8000000-0xfbffffff could not be reserved
    system 00:01: iomem range 0xfc000000-0xfebfffff has been reserved
    system 00:01: iomem range 0xfec00000-0xfec7ffff could not be reserved
    system 00:01: iomem range 0xfec80000-0xfecfffff has been reserved
    system 00:01: iomem range 0xfee00000-0xfeefffff could not be reserved
    system 00:01: iomem range 0xfef00000-0xfef7ffff has been reserved
    system 00:01: iomem range 0xfef80000-0xfeffffff has been reserved
    system 00:01: iomem range 0xfff00000-0xffffffff could not be reserved
    PM-Timer running at invalid rate: 349% of normal - aborting.
    PCI: Bridge: 0000:00:08.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:02:00.0
    PCI: Bridge: 0000:00:0b.0
    IO window: 4000-4fff
    MEM window: 0xdc000000-0xdcffffff
    PREFETCH window: 0x00000000de000000-0x00000000efffffff
    PCI: Bridge: 0000:00:10.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:12.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:13.0
    IO window: disabled.
    MEM window: 0xdde00000-0xddefffff
    PREFETCH window: disabled.
    PCI: Setting latency timer of device 0000:00:08.0 to 64
    PCI: Setting latency timer of device 0000:00:0b.0 to 64
    ACPI: PCI Interrupt Link [LKR0] enabled at IRQ 23
    ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LKR0] -> GSI 23 (level, high) ->
    IRQ 23
    PCI: Setting latency timer of device 0000:00:10.0 to 64
    ACPI: PCI Interrupt Link [LKR2] enabled at IRQ 22
    ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LKR2] -> GSI 22 (level, high) ->
    IRQ 22
    PCI: Setting latency timer of device 0000:00:12.0 to 64
    ACPI: PCI Interrupt Link [LKR3] enabled at IRQ 21
    ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LKR3] -> GSI 21 (level, high) ->
    IRQ 21
    PCI: Setting latency timer of device 0000:00:13.0 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    checking if image is initramfs...it isn't (no cpio magic); looks like an
    initrd
    Freeing initrd memory: 62994k freed
    Simple Boot Flag at 0x38 set to 0x1
    audit: initializing netlink socket (disabled)
    type=2000 audit(1217245531.579:1): initialized
    Total HugeTLB memory allocated, 0
    msgmni has been set to 1767
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered (default)
    io scheduler cfq registered
    pci 0000:02:00.0: Boot video device
    PCI: Setting latency timer of device 0000:00:10.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:10.0cie00]
    PCI: Setting latency timer of device 0000:00:12.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:12.0cie00]
    PCI: Setting latency timer of device 0000:00:13.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:13.0cie00]
    vesafb: framebuffer at 0xdf000000, mapped to 0xf8880000, using 3072k, total
    14336k
    vesafb: mode is 1024x768x16, linelength=2048, pages=1
    vesafb: protected mode interface info at c000:b640
    vesafb: pmi: set display start = c00cb6a3, set palette = c00cb6fe
    vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf
    3d0 3d1 3d2 3d3 3d4 3d5 3da
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    FDC 0 is a post-1991 82077
    brd: module loaded
    Loading iSCSI transport class v2.0-869.
    PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    EISA: Probing bus 0 at eisa.0
    Cannot allocate resource for EISA slot 1
    Cannot allocate resource for EISA slot 3
    Cannot allocate resource for EISA slot 4
    EISA: Detected 0 cards.
    TCP cubic registered
    NET: Registered protocol family 15
    Starting balanced_irq
    Using IPI No-Shortcut mode
    input: AT Translated Set 2 keyboard as /class/input/input0
    RAMDISK: Compressed image found at block 0
    VFS: Mounted root (ext2 filesystem).
    Freeing unused kernel memory: 340k freed
    Failed to execute /etc/init. Attempting defaults...
    ACPI: ACPI0007:00 is registered as cooling_device0
    ACPI: ACPI0007:01 is registered as cooling_device1
    input: Power Button (FF) as /class/input/input1
    ACPI: Power Button (FF) [PWRF]
    input: Power Button (CM) as /class/input/input2
    ACPI: Power Button (CM) [PWRB]
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
    ACPI: PCI Interrupt Link [LNKJ] enabled at IRQ 20
    ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKJ] -> GSI 20 (level, high) ->
    IRQ 20
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    ohci_hcd 0000:00:02.0: OHCI Host Controller
    ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
    ohci_hcd 0000:00:02.0: irq 20, io mem 0xddbf9000
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    No dock devices found.
    ACPI: PCI Interrupt Link [LNKR] enabled at IRQ 19
    ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKR] -> GSI 19 (level, high) ->
    IRQ 19
    PCI: Setting latency timer of device 0000:00:04.0 to 64
    ohci_hcd 0000:00:04.0: OHCI Host Controller
    ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
    ohci_hcd 0000:00:04.0: irq 19, io mem 0xddbf8000
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 6 ports detected
    libata version 3.00 loaded.
    ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 18
    ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKI] -> GSI 18 (level, high) ->
    IRQ 18
    PCI: Setting latency timer of device 0000:00:02.1 to 64
    ehci_hcd 0000:00:02.1: EHCI Host Controller
    ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
    ehci_hcd 0000:00:02.1: debug port 1
    PCI: cache line size of 64 is not supported by device 0000:00:02.1
    ehci_hcd 0000:00:02.1: irq 18, io mem 0xddbf6c00
    ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 6 ports detected
    ACPI: PCI Interrupt Link [LNKS] enabled at IRQ 17
    ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [LNKS] -> GSI 17 (level, high) ->
    IRQ 17
    PCI: Setting latency timer of device 0000:00:04.1 to 64
    ehci_hcd 0000:00:04.1: EHCI Host Controller
    ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4
    ehci_hcd 0000:00:04.1: debug port 1
    PCI: cache line size of 64 is not supported by device 0000:00:04.1
    ehci_hcd 0000:00:04.1: irq 17, io mem 0xddbf6800
    ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 6 ports detected
    tpm_inf_pnp 00:02: Found TPM with ID IFX0102
    PCI: Setting latency timer of device 0000:00:09.0 to 64
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    ahci 0000:00:09.0: version 3.0
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    serial 00:0e: activated
    00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl IDE mode
    ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio
    PCI: Setting latency timer of device 0000:00:09.0 to 64
    ------------[ cut here ]------------
    WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100
    [libata]()
    Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+)
    ata_generic tpm_infineon tpm tpm_bios pata_acpi libata shpchp dock
    pci_hotplug ehci_hcd ohci_hcd usbcore container thermal button processor
    evdev
    Pid: 1937, comm: modprobe Not tainted 2.6.26 #1
    [] warn_on_slowpath+0x5f/0x90
    [] finish_task_switch+0x95/0xa0
    [] dma_alloc_coherent+0x122/0x2b0
    [] devres_add+0x31/0x50
    [] dmam_alloc_coherent+0x6c/0x90
    [] ahci_port_resume+0x5f/0x70 [ahci]
    [] devres_add+0x31/0x50
    [] ata_host_start+0xed/0x170 [libata]
    [] pci_bus_write_config_byte+0x5a/0x70
    [] ata_host_activate+0xf6/0x100 [libata]
    [] ahci_init_one+0x899/0xac0 [ahci]
    [] pci_device_probe+0x56/0x80
    [] driver_probe_device+0x82/0x180
    [] __driver_attach+0x6c/0x70
    [] bus_for_each_dev+0x3b/0x60
    [] driver_attach+0x16/0x20
    [] __driver_attach+0x0/0x70
    [] bus_add_driver+0xa9/0x210
    [] pci_device_remove+0x0/0x40
    [] driver_register+0x4d/0x120
    [] __pci_register_driver+0x3d/0x80
    [] sys_init_module+0x84/0x1b0
    [] sysenter_past_esp+0x6a/0x99
    =======================
    ---[ end trace 21da9b6136ad63e5 ]---
    scsi0 : ahci
    scsi1 : ahci
    scsi2 : ahci
    scsi3 : ahci
    scsi4 : ahci
    scsi5 : ahci
    ata1: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa100
    ata2: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa180
    ata3: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa200
    ata4: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa280
    ata5: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa300
    ata6: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa380
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata1: failed to recover some devices, retrying in 5 secs
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata1: failed to recover some devices, retrying in 5 secs
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata1: failed to recover some devices, retrying in 5 secs
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata2.00: qc timeout (cmd 0xec)
    ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5)
    ata2: failed to recover some devices, retrying in 5 secs
    ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata2.00: qc timeout (cmd 0xec)
    ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5)
    ata2: failed to recover some devices, retrying in 5 secs
    ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata2.00: qc timeout (cmd 0xec)
    ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5)
    ata2: failed to recover some devices, retrying in 5 secs
    ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata3: SATA link down (SStatus 0 SControl 300)
    ata4: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    tg3.c:v3.92.1 (June 9, 2008)
    ACPI: PCI Interrupt Link [LK3A] enabled at IRQ 16
    ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LK3A] -> GSI 16 (level, high) ->
    IRQ 16
    PCI: Setting latency timer of device 0000:05:00.0 to 64
    eth0: Tigon3 [partno(BCM95787) rev b002 PHY(5787)] (PCI Express)
    10/100/1000Base-T Ethernet 00:19:99:23:e4:7d
    eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
    eth0: dma_rwctrl[76180000] dma_mask[64-bit]
    fuse init (API version 7.9)
    device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
    dm-devel@redhat.com
    NET: Registered protocol family 17
    tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is on for TX and on for RX.
    tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is on for TX and on for RX.


    Any help?

    --
    Jan Schneider

    uib gmbh
    Bonifaziusplatz 1B
    55118 Mainz

    Tel. 06131 / 27561-20
    Fax 06131 / 27561-22

    E-Mail: j.schneider@uib.de

    Internet: www.uib.de

    Geschäftsführer: dr. detlef oertel
    Handelsregister: Amtsgericht Mainz HRB 6942
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  2. Re: nvidia MCP78B ahci failed to IDENTIFY error on 2.6.26


    (cc linux-ide)

    On Mon, 28 Jul 2008 12:03:38 +0200 Jan Schneider wrote:

    > Hi,
    >
    > I get the follwing errors when booting 2.6.26 on a FSC Esprimo P5625 (nvidia
    > MCP78B).


    Did any earlier kernels work OK? If so, which version(s)?

    Thanks.

    > ------------[ cut here ]------------
    > WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100
    > [libata]()
    > Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+)
    > ata_generic tpm_infineon tpm tpm_bios pata_acpi libata shpchp dock
    > pci_hotplug ehci_hcd ohci_hcd usbcore container thermal button processor
    > evdev
    > Pid: 1937, comm: modprobe Not tainted 2.6.26 #1
    > [] warn_on_slowpath+0x5f/0x90
    > [] finish_task_switch+0x95/0xa0
    > [] dma_alloc_coherent+0x122/0x2b0
    > [] devres_add+0x31/0x50
    > [] dmam_alloc_coherent+0x6c/0x90
    > [] ahci_port_resume+0x5f/0x70 [ahci]
    > [] devres_add+0x31/0x50
    > [] ata_host_start+0xed/0x170 [libata]
    > [] pci_bus_write_config_byte+0x5a/0x70
    > [] ata_host_activate+0xf6/0x100 [libata]
    > [] ahci_init_one+0x899/0xac0 [ahci]
    > [] pci_device_probe+0x56/0x80
    > [] driver_probe_device+0x82/0x180
    > [] __driver_attach+0x6c/0x70
    > [] bus_for_each_dev+0x3b/0x60
    > [] driver_attach+0x16/0x20
    > [] __driver_attach+0x0/0x70
    > [] bus_add_driver+0xa9/0x210
    > [] pci_device_remove+0x0/0x40
    > [] driver_register+0x4d/0x120
    > [] __pci_register_driver+0x3d/0x80
    > [] sys_init_module+0x84/0x1b0
    > [] sysenter_past_esp+0x6a/0x99
    > =======================
    > ---[ end trace 21da9b6136ad63e5 ]---
    >
    > The serial ata harddisk does not appear.
    >
    > ---------[ lspci -n ]---------
    > 00:00.0 0500: 10de:0754 (rev a2)
    > 00:01.0 0601: 10de:075c (rev a2)
    > 00:01.1 0c05: 10de:0752 (rev a1)
    > 00:01.2 0500: 10de:0751 (rev a1)
    > 00:01.4 0500: 10de:0568 (rev a1)
    > 00:02.0 0c03: 10de:077b (rev a1)
    > 00:02.1 0c03: 10de:077c (rev a1)
    > 00:04.0 0c03: 10de:077d (rev a1)
    > 00:04.1 0c03: 10de:077e (rev a1)
    > 00:07.0 0403: 10de:0774 (rev a1)
    > 00:08.0 0604: 10de:075a (rev a1)
    > 00:09.0 0101: 10de:0ad0 (rev a2)
    > 00:0b.0 0604: 10de:0569 (rev a1)
    > 00:10.0 0604: 10de:0778 (rev a1)
    > 00:12.0 0604: 10de:075b (rev a1)
    > 00:13.0 0604: 10de:077a (rev a1)
    > 00:18.0 0600: 1022:1100
    > 00:18.1 0600: 1022:1101
    > 00:18.2 0600: 1022:1102
    > 00:18.3 0600: 1022:1103
    > 02:00.0 0300: 10de:084b (rev a2)
    > 05:00.0 0200: 14e4:169b (rev 02)
    > ----------------------------------
    >
    > Full dmesg output:
    >
    > Linux version 2.6.26 (root@pcbon14) (gcc version 4.2.3 (Ubuntu
    > 4.2.3-2ubuntu7)) #1 SMP PREEMPT Mon Jul 21 16:44:03 UTC 2008
    > BIOS-provided physical RAM map:
    > BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
    > BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
    > BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
    > BIOS-e820: 0000000000100000 - 0000000037f40000 (usable)
    > BIOS-e820: 0000000037f40000 - 0000000037f4d000 (ACPI data)
    > BIOS-e820: 0000000037f4d000 - 0000000037f4e000 (ACPI NVS)
    > BIOS-e820: 0000000037f4e000 - 0000000040000000 (reserved)
    > BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
    > BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    > BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    > 0MB HIGHMEM available.
    > 895MB LOWMEM available.
    > found SMP MP-table at [c00f75e0] 000f75e0
    > Entering add_active_range(0, 0, 229184) 0 entries of 256 used
    > Zone PFN ranges:
    > DMA 0 -> 4096
    > Normal 4096 -> 229184
    > HighMem 229184 -> 229184
    > Movable zone start PFN for each node
    > early_node_map[1] active PFN ranges
    > 0: 0 -> 229184
    > On node 0 totalpages: 229184
    > DMA zone: 32 pages used for memmap
    > DMA zone: 0 pages reserved
    > DMA zone: 4064 pages, LIFO batch:0
    > Normal zone: 1759 pages used for memmap
    > Normal zone: 223329 pages, LIFO batch:31
    > HighMem zone: 0 pages used for memmap
    > Movable zone: 0 pages used for memmap
    > DMI present.
    > ACPI: RSDP 000F75B0, 0024 (r2 PTLTD )
    > ACPI: XSDT 37F45097, 007C (r1 FSC PC 60000 LTP 0)
    > ACPI: FACP 37F4C7FA, 00F4 (r3 FSC 60000 PTL_ F4240)
    > ACPI: DSDT 37F45113, 7673 (r1 FSC D2721/A1 60000 MSFT 3000001)
    > ACPI: FACS 37F4DFC0, 0040
    > ACPI: TCPA 37F4C8EE, 0032 (r1 Phoeni x 60000 TL 0)
    > ACPI: WDAT 37F4C920, 0104 (r1 PTLTD WDATTBL 60000 LTP 1)
    > ACPI: SSDT 37F4CA24, 0248 (r1 AMD POWERNOW 60000 AMD 1)
    > ACPI: SRAT 37F4CC6C, 00A0 (r1 AMD HAMMER 60000 AMD 1)
    > ACPI: ASF! 37F4CD0C, 0070 (r32 OEMID OEMTBL 60000 PTL 1)
    > ACPI: SLIC 37F4CD7C, 0176 (r1 FSC PC 60000 LTP 0)
    > ACPI: MCFG 37F4CEF2, 003C (r1 PTLTD MCFG 60000 LTP 0)
    > ACPI: HPET 37F4CF2E, 0038 (r1 PTLTD HPETTBL 60000 LTP 1)
    > ACPI: APIC 37F4CF66, 0072 (r1 PTLTD APIC 60000 LTP 0)
    > ACPI: BOOT 37F4CFD8, 0028 (r1 PTLTD $SBFTBL$ 60000 LTP 1)
    > ACPI: DMI detected: Fujitsu Siemens
    > Detected use of extended apic ids on hypertransport bus
    > ACPI: PM-Timer IO Port: 0x1008
    > ACPI: Local APIC address 0xfee00000
    > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    > ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    > ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    > ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    > IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    > ACPI: IRQ0 used by override.
    > ACPI: IRQ2 used by override.
    > ACPI: IRQ9 used by override.
    > Enabling APIC mode: Flat. Using 1 I/O APICs
    > ACPI: HPET id: 0x10de8201 base: 0xfed00000
    > Using ACPI (MADT) for SMP configuration information
    > Allocating PCI resources starting at 50000000 (gap: 40000000:b8000000)
    > SMP: Allowing 2 CPUs, 0 hotplug CPUs
    > PERCPU: Allocating 36392 bytes of per cpu data
    > NR_CPUS: 32, nr_cpu_ids: 2
    > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227393
    > Kernel command line: lang=de video=vesa:ywrap,mtrr
    > pckey=4e6842c5129e7882c318378dde52fe2e service=192.168.1.14 vga=791
    > initrd=miniroot.gz reboot=b product=winxppro init=/etc/init quiet hn=evb
    > ramdisk_size=185320 splash BOOT_IMAGE=install
    > mapped APIC to ffffb000 (fee00000)
    > mapped IOAPIC to ffffa000 (fec00000)
    > Enabling fast FPU save and restore... done.
    > Enabling unmasked SIMD FPU exception support... done.
    > Initializing CPU#0
    > PID hash table entries: 4096 (order: 12, 16384 bytes)
    > Extended CMOS year: 2000
    > Detected 2300.065 MHz processor.
    > spurious 8259A interrupt: IRQ7.
    > Console: colour dummy device 80x25
    > console [tty0] enabled
    > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    > Memory: 841640k/916736k available (2127k kernel code, 74572k reserved, 758k
    > data, 340k init, 0k highmem)
    > virtual kernel memory layout:
    > fixmap : 0xffe14000 - 0xfffff000 (1964 kB)
    > pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    > vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
    > lowmem : 0xc0000000 - 0xf7f40000 ( 895 MB)
    > .init : 0xc03d7000 - 0xc042c000 ( 340 kB)
    > .data : 0xc0313e37 - 0xc03d1a20 ( 758 kB)
    > .text : 0xc0100000 - 0xc0313e37 (2127 kB)
    > Checking if this processor honours the WP bit even in supervisor mode...Ok.
    > CPA: page pool initialized 1 of 1 pages preallocated
    > hpet clockevent registered
    > Calibrating delay using timer specific routine.. 4605.32 BogoMIPS
    > (lpj=9210650)
    > Mount-cache hash table entries: 512
    > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    > CPU: L2 Cache: 512K (64 bytes/line)
    > CPU 0(2) -> Core 0
    > Intel machine check architecture supported.
    > Intel machine check reporting enabled on CPU#0.
    > Checking 'hlt' instruction... OK.
    > ACPI: Core revision 20080321
    > ENABLING IO-APIC IRQs
    > ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
    > CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02
    > APIC calibration not consistent with PM Timer: 349ms instead of 100ms
    > APIC delta adjusted to PM-Timer: 357954 (1249981)
    > Booting processor 1/1 ip 6000
    > Initializing CPU#1
    > Calibrating delay using timer specific routine.. 1317.37 BogoMIPS
    > (lpj=2634740)
    > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    > CPU: L2 Cache: 512K (64 bytes/line)
    > CPU 1(2) -> Core 1
    > Intel machine check architecture supported.
    > Intel machine check reporting enabled on CPU#1.
    > CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02
    > Brought up 2 CPUs
    > Total of 2 processors activated (5922.69 BogoMIPS).
    > CPU0 attaching sched-domain:
    > domain 0: span 0-1
    > groups: 0 1
    > CPU1 attaching sched-domain:
    > domain 0: span 0-1
    > groups: 1 0
    > net_namespace: 200 bytes
    > NET: Registered protocol family 16
    > EISA bus registered
    > ACPI: bus type pci registered
    > PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 5
    > PCI: MCFG area at f8000000 reserved in E820
    > PCI: Using MMCONFIG for extended config space
    > PCI: Using configuration type 1 for base access
    > Setting up standard PCI resources
    > ACPI: EC: Look up EC in DSDT
    > ACPI: Interpreter enabled
    > ACPI: (supports S0 S1 S3 S5)
    > ACPI: Using IOAPIC for interrupt routing
    > ACPI: Device [ECP] status [00000008]: functional but not present; setting
    > present
    > ACPI: Device [COM2] status [00000008]: functional but not present; setting
    > present
    > ACPI: PCI Root Bridge [PCI0] (0000:00)
    > PCI: Transparent bridge - 0000:00:08.0
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXA._PRT]
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXB._PRT]
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXL._PRT]
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT]
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
    > ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    > disabled.
    > ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    > disabled.
    > ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    > disabled.
    > ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0,
    > disabled.
    > ACPI: PCI Interrupt Link [LK0A] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LK0B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK0C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK0D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK1A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK1B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK1C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK1D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK2A] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LK2B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK2C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK2D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK3A] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LK3B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK3C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK3D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK4A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK4B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK4C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK4D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK5A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK5B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK5C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK5D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK6A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK6B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK6C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK6D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK7A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK7B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK7C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LK7D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR0] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR2] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR3] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR4] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR5] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR6] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LKR7] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *5
    > ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *10
    > ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [LNKQ] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LNKR] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LNKS] (IRQs 16 17 18 19 20 21 22 23) *11
    > ACPI: PCI Interrupt Link [LNKT] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    > Linux Plug and Play Support v0.97 (c) Adam Belay
    > pnp: PnP ACPI init
    > ACPI: bus type pnp registered
    > pnp: PnP ACPI: found 15 devices
    > ACPI: ACPI bus type pnp unregistered
    > PnPBIOS: Disabled by ACPI PNP
    > SCSI subsystem initialized
    > PCI: Using ACPI for IRQ routing
    > ACPI: RTC can wake from S4
    > system 00:01: ioport range 0x4d0-0x4d1 has been reserved
    > system 00:01: ioport range 0x500-0x57f has been reserved
    > system 00:01: ioport range 0x1000-0x10e7 has been reserved
    > system 00:01: ioport range 0x1200-0x12fe has been reserved
    > system 00:01: ioport range 0x1400-0x14fe has been reserved
    > system 00:01: ioport range 0x1500-0x15fe has been reserved
    > system 00:01: ioport range 0x1600-0x16fe has been reserved
    > system 00:01: ioport range 0x1700-0x17fe has been reserved
    > system 00:01: ioport range 0x1800-0x18fe has been reserved
    > system 00:01: ioport range 0x1900-0x19fe has been reserved
    > system 00:01: ioport range 0x1a00-0x1afe has been reserved
    > system 00:01: ioport range 0x1c00-0x1cfe has been reserved
    > system 00:01: ioport range 0xfe00-0xfe00 has been reserved
    > system 00:01: ioport range 0xff00-0xff00 has been reserved
    > system 00:01: iomem range 0xf8000000-0xfbffffff could not be reserved
    > system 00:01: iomem range 0xfc000000-0xfebfffff has been reserved
    > system 00:01: iomem range 0xfec00000-0xfec7ffff could not be reserved
    > system 00:01: iomem range 0xfec80000-0xfecfffff has been reserved
    > system 00:01: iomem range 0xfee00000-0xfeefffff could not be reserved
    > system 00:01: iomem range 0xfef00000-0xfef7ffff has been reserved
    > system 00:01: iomem range 0xfef80000-0xfeffffff has been reserved
    > system 00:01: iomem range 0xfff00000-0xffffffff could not be reserved
    > PM-Timer running at invalid rate: 349% of normal - aborting.
    > PCI: Bridge: 0000:00:08.0
    > IO window: disabled.
    > MEM window: disabled.
    > PREFETCH window: disabled.
    > PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:02:00.0
    > PCI: Bridge: 0000:00:0b.0
    > IO window: 4000-4fff
    > MEM window: 0xdc000000-0xdcffffff
    > PREFETCH window: 0x00000000de000000-0x00000000efffffff
    > PCI: Bridge: 0000:00:10.0
    > IO window: disabled.
    > MEM window: disabled.
    > PREFETCH window: disabled.
    > PCI: Bridge: 0000:00:12.0
    > IO window: disabled.
    > MEM window: disabled.
    > PREFETCH window: disabled.
    > PCI: Bridge: 0000:00:13.0
    > IO window: disabled.
    > MEM window: 0xdde00000-0xddefffff
    > PREFETCH window: disabled.
    > PCI: Setting latency timer of device 0000:00:08.0 to 64
    > PCI: Setting latency timer of device 0000:00:0b.0 to 64
    > ACPI: PCI Interrupt Link [LKR0] enabled at IRQ 23
    > ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LKR0] -> GSI 23 (level, high) ->
    > IRQ 23
    > PCI: Setting latency timer of device 0000:00:10.0 to 64
    > ACPI: PCI Interrupt Link [LKR2] enabled at IRQ 22
    > ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LKR2] -> GSI 22 (level, high) ->
    > IRQ 22
    > PCI: Setting latency timer of device 0000:00:12.0 to 64
    > ACPI: PCI Interrupt Link [LKR3] enabled at IRQ 21
    > ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LKR3] -> GSI 21 (level, high) ->
    > IRQ 21
    > PCI: Setting latency timer of device 0000:00:13.0 to 64
    > NET: Registered protocol family 2
    > IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    > TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    > TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    > TCP: Hash tables configured (established 131072 bind 65536)
    > TCP reno registered
    > NET: Registered protocol family 1
    > checking if image is initramfs...it isn't (no cpio magic); looks like an
    > initrd
    > Freeing initrd memory: 62994k freed
    > Simple Boot Flag at 0x38 set to 0x1
    > audit: initializing netlink socket (disabled)
    > type=2000 audit(1217245531.579:1): initialized
    > Total HugeTLB memory allocated, 0
    > msgmni has been set to 1767
    > io scheduler noop registered
    > io scheduler anticipatory registered
    > io scheduler deadline registered (default)
    > io scheduler cfq registered
    > pci 0000:02:00.0: Boot video device
    > PCI: Setting latency timer of device 0000:00:10.0 to 64
    > assign_interrupt_mode Found MSI capability
    > Allocate Port Service[0000:00:10.0cie00]
    > PCI: Setting latency timer of device 0000:00:12.0 to 64
    > assign_interrupt_mode Found MSI capability
    > Allocate Port Service[0000:00:12.0cie00]
    > PCI: Setting latency timer of device 0000:00:13.0 to 64
    > assign_interrupt_mode Found MSI capability
    > Allocate Port Service[0000:00:13.0cie00]
    > vesafb: framebuffer at 0xdf000000, mapped to 0xf8880000, using 3072k, total
    > 14336k
    > vesafb: mode is 1024x768x16, linelength=2048, pages=1
    > vesafb: protected mode interface info at c000:b640
    > vesafb: pmi: set display start = c00cb6a3, set palette = c00cb6fe
    > vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf
    > 3d0 3d1 3d2 3d3 3d4 3d5 3da
    > vesafb: scrolling: redraw
    > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    > Console: switching to colour frame buffer device 128x48
    > fb0: VESA VGA frame buffer device
    > isapnp: Scanning for PnP cards...
    > isapnp: No Plug & Play device found
    > FDC 0 is a post-1991 82077
    > brd: module loaded
    > Loading iSCSI transport class v2.0-869.
    > PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    > serio: i8042 KBD port at 0x60,0x64 irq 1
    > serio: i8042 AUX port at 0x60,0x64 irq 12
    > mice: PS/2 mouse device common for all mice
    > EISA: Probing bus 0 at eisa.0
    > Cannot allocate resource for EISA slot 1
    > Cannot allocate resource for EISA slot 3
    > Cannot allocate resource for EISA slot 4
    > EISA: Detected 0 cards.
    > TCP cubic registered
    > NET: Registered protocol family 15
    > Starting balanced_irq
    > Using IPI No-Shortcut mode
    > input: AT Translated Set 2 keyboard as /class/input/input0
    > RAMDISK: Compressed image found at block 0
    > VFS: Mounted root (ext2 filesystem).
    > Freeing unused kernel memory: 340k freed
    > Failed to execute /etc/init. Attempting defaults...
    > ACPI: ACPI0007:00 is registered as cooling_device0
    > ACPI: ACPI0007:01 is registered as cooling_device1
    > input: Power Button (FF) as /class/input/input1
    > ACPI: Power Button (FF) [PWRF]
    > input: Power Button (CM) as /class/input/input2
    > ACPI: Power Button (CM) [PWRB]
    > usbcore: registered new interface driver usbfs
    > usbcore: registered new interface driver hub
    > usbcore: registered new device driver usb
    > ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
    > ACPI: PCI Interrupt Link [LNKJ] enabled at IRQ 20
    > ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKJ] -> GSI 20 (level, high) ->
    > IRQ 20
    > PCI: Setting latency timer of device 0000:00:02.0 to 64
    > ohci_hcd 0000:00:02.0: OHCI Host Controller
    > ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
    > ohci_hcd 0000:00:02.0: irq 20, io mem 0xddbf9000
    > usb usb1: configuration #1 chosen from 1 choice
    > hub 1-0:1.0: USB hub found
    > hub 1-0:1.0: 6 ports detected
    > pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    > No dock devices found.
    > ACPI: PCI Interrupt Link [LNKR] enabled at IRQ 19
    > ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKR] -> GSI 19 (level, high) ->
    > IRQ 19
    > PCI: Setting latency timer of device 0000:00:04.0 to 64
    > ohci_hcd 0000:00:04.0: OHCI Host Controller
    > ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
    > ohci_hcd 0000:00:04.0: irq 19, io mem 0xddbf8000
    > usb usb2: configuration #1 chosen from 1 choice
    > hub 2-0:1.0: USB hub found
    > hub 2-0:1.0: 6 ports detected
    > libata version 3.00 loaded.
    > ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 18
    > ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKI] -> GSI 18 (level, high) ->
    > IRQ 18
    > PCI: Setting latency timer of device 0000:00:02.1 to 64
    > ehci_hcd 0000:00:02.1: EHCI Host Controller
    > ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
    > ehci_hcd 0000:00:02.1: debug port 1
    > PCI: cache line size of 64 is not supported by device 0000:00:02.1
    > ehci_hcd 0000:00:02.1: irq 18, io mem 0xddbf6c00
    > ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    > usb usb3: configuration #1 chosen from 1 choice
    > hub 3-0:1.0: USB hub found
    > hub 3-0:1.0: 6 ports detected
    > ACPI: PCI Interrupt Link [LNKS] enabled at IRQ 17
    > ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [LNKS] -> GSI 17 (level, high) ->
    > IRQ 17
    > PCI: Setting latency timer of device 0000:00:04.1 to 64
    > ehci_hcd 0000:00:04.1: EHCI Host Controller
    > ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4
    > ehci_hcd 0000:00:04.1: debug port 1
    > PCI: cache line size of 64 is not supported by device 0000:00:04.1
    > ehci_hcd 0000:00:04.1: irq 17, io mem 0xddbf6800
    > ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    > usb usb4: configuration #1 chosen from 1 choice
    > hub 4-0:1.0: USB hub found
    > hub 4-0:1.0: 6 ports detected
    > tpm_inf_pnp 00:02: Found TPM with ID IFX0102
    > PCI: Setting latency timer of device 0000:00:09.0 to 64
    > shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    > ahci 0000:00:09.0: version 3.0
    > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    > 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    > serial 00:0e: activated
    > 00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    > ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl IDE mode
    > ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio
    > PCI: Setting latency timer of device 0000:00:09.0 to 64
    > ------------[ cut here ]------------
    > WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100
    > [libata]()
    > Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+)
    > ata_generic tpm_infineon tpm tpm_bios pata_acpi libata shpchp dock
    > pci_hotplug ehci_hcd ohci_hcd usbcore container thermal button processor
    > evdev
    > Pid: 1937, comm: modprobe Not tainted 2.6.26 #1
    > [] warn_on_slowpath+0x5f/0x90
    > [] finish_task_switch+0x95/0xa0
    > [] dma_alloc_coherent+0x122/0x2b0
    > [] devres_add+0x31/0x50
    > [] dmam_alloc_coherent+0x6c/0x90
    > [] ahci_port_resume+0x5f/0x70 [ahci]
    > [] devres_add+0x31/0x50
    > [] ata_host_start+0xed/0x170 [libata]
    > [] pci_bus_write_config_byte+0x5a/0x70
    > [] ata_host_activate+0xf6/0x100 [libata]
    > [] ahci_init_one+0x899/0xac0 [ahci]
    > [] pci_device_probe+0x56/0x80
    > [] driver_probe_device+0x82/0x180
    > [] __driver_attach+0x6c/0x70
    > [] bus_for_each_dev+0x3b/0x60
    > [] driver_attach+0x16/0x20
    > [] __driver_attach+0x0/0x70
    > [] bus_add_driver+0xa9/0x210
    > [] pci_device_remove+0x0/0x40
    > [] driver_register+0x4d/0x120
    > [] __pci_register_driver+0x3d/0x80
    > [] sys_init_module+0x84/0x1b0
    > [] sysenter_past_esp+0x6a/0x99
    > =======================
    > ---[ end trace 21da9b6136ad63e5 ]---
    > scsi0 : ahci
    > scsi1 : ahci
    > scsi2 : ahci
    > scsi3 : ahci
    > scsi4 : ahci
    > scsi5 : ahci
    > ata1: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa100
    > ata2: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa180
    > ata3: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa200
    > ata4: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa280
    > ata5: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa300
    > ata6: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa380
    > ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    > ata1.00: qc timeout (cmd 0xec)
    > ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    > ata1: failed to recover some devices, retrying in 5 secs
    > ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    > ata1.00: qc timeout (cmd 0xec)
    > ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    > ata1: failed to recover some devices, retrying in 5 secs
    > ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    > ata1.00: qc timeout (cmd 0xec)
    > ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    > ata1: failed to recover some devices, retrying in 5 secs
    > ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    > ata2.00: qc timeout (cmd 0xec)
    > ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5)
    > ata2: failed to recover some devices, retrying in 5 secs
    > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    > ata2.00: qc timeout (cmd 0xec)
    > ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5)
    > ata2: failed to recover some devices, retrying in 5 secs
    > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    > ata2.00: qc timeout (cmd 0xec)
    > ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5)
    > ata2: failed to recover some devices, retrying in 5 secs
    > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    > ata3: SATA link down (SStatus 0 SControl 300)
    > ata4: SATA link down (SStatus 0 SControl 300)
    > ata5: SATA link down (SStatus 0 SControl 300)
    > ata6: SATA link down (SStatus 0 SControl 300)
    > tg3.c:v3.92.1 (June 9, 2008)
    > ACPI: PCI Interrupt Link [LK3A] enabled at IRQ 16
    > ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LK3A] -> GSI 16 (level, high) ->
    > IRQ 16
    > PCI: Setting latency timer of device 0000:05:00.0 to 64
    > eth0: Tigon3 [partno(BCM95787) rev b002 PHY(5787)] (PCI Express)
    > 10/100/1000Base-T Ethernet 00:19:99:23:e4:7d
    > eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
    > eth0: dma_rwctrl[76180000] dma_mask[64-bit]
    > fuse init (API version 7.9)
    > device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
    > dm-devel@redhat.com
    > NET: Registered protocol family 17
    > tg3: eth0: Link is up at 100 Mbps, full duplex.
    > tg3: eth0: Flow control is on for TX and on for RX.
    > tg3: eth0: Link is up at 100 Mbps, full duplex.
    > tg3: eth0: Flow control is on for TX and on for RX.
    >
    >
    > Any help?
    >
    > --
    > Jan Schneider
    >
    > uib gmbh
    > Bonifaziusplatz 1B
    > 55118 Mainz
    >
    > Tel. 06131 / 27561-20
    > Fax 06131 / 27561-22
    >
    > E-Mail: j.schneider@uib.de
    >
    > Internet: www.uib.de
    >
    > Gesch__ftsf__hrer: dr. detlef oertel
    > Handelsregister: Amtsgericht Mainz HRB 6942
    > --
    > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    > the body of a message to majordomo@vger.kernel.org
    > More majordomo info at http://vger.kernel.org/majordomo-info.html
    > Please read the FAQ at http://www.tux.org/lkml/

    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  3. [bug] 2.6.27-rc1: I/O errors after resume

    With 2.6.27-rc1 things break badly after resume on my T60. Dmesg and
    config attached. 2.6.26 worked fine.

    Miklos


    [ 0.000000] Linux version 2.6.27-rc1-dirty (mszeredi@tucsk) (gcc version 4.2.1 (SUSE Linux)) #16 SMP Wed Jul 30 10:14:24 CEST 2008
    [ 0.000000] Command line: root=/dev/sda2 vga=0x365
    [ 0.000000] KERNEL supported cpus:
    [ 0.000000] Intel GenuineIntel
    [ 0.000000] AMD AuthenticAMD
    [ 0.000000] Centaur CentaurHauls
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bfed0000 (usable)
    [ 0.000000] BIOS-e820: 00000000bfed0000 - 00000000bfedf000 (ACPI data)
    [ 0.000000] BIOS-e820: 00000000bfedf000 - 00000000bff00000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 00000000bff00000 - 00000000c0000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
    [ 0.000000] last_pfn = 0xbfed0 max_arch_pfn = 0x3ffffffff
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] init_memory_mapping
    [ 0.000000] 0000000000 - 00bfe00000 page 2M
    [ 0.000000] 00bfe00000 - 00bfed0000 page 4k
    [ 0.000000] kernel direct mapping tables up to bfed0000 @ 8000-d000
    [ 0.000000] last_map_addr: bfed0000 end: bfed0000
    [ 0.000000] DMI present.
    [ 0.000000] ACPI: RSDP 000F67E0, 0024 (r2 LENOVO)
    [ 0.000000] ACPI: XSDT BFED13C7, 008C (r1 LENOVO TP-79 2190 LTP 0)
    [ 0.000000] ACPI: FACP BFED1500, 00F4 (r3 LENOVO TP-79 2190 LNVO 1)
    [ 0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20080609]
    [ 0.000000] ACPI: DSDT BFED185E, D3C2 (r1 LENOVO TP-79 2190 MSFT 100000E)
    [ 0.000000] ACPI: FACS BFEF4000, 0040
    [ 0.000000] ACPI: SSDT BFED16B4, 01AA (r1 LENOVO TP-79 2190 MSFT 100000E)
    [ 0.000000] ACPI: ECDT BFEDEC20, 0052 (r1 LENOVO TP-79 2190 LNVO 1)
    [ 0.000000] ACPI: TCPA BFEDEC72, 0032 (r2 LENOVO TP-79 2190 LNVO 1)
    [ 0.000000] ACPI: APIC BFEDECA4, 0068 (r1 LENOVO TP-79 2190 LNVO 1)
    [ 0.000000] ACPI: MCFG BFEDED0C, 003C (r1 LENOVO TP-79 2190 LNVO 1)
    [ 0.000000] ACPI: HPET BFEDED48, 0038 (r1 LENOVO TP-79 2190 LNVO 1)
    [ 0.000000] ACPI: SLIC BFEDEE62, 0176 (r1 LENOVO TP-79 2190 LTP 0)
    [ 0.000000] ACPI: BOOT BFEDEFD8, 0028 (r1 LENOVO TP-79 2190 LTP 1)
    [ 0.000000] ACPI: SSDT BFEF2655, 025F (r1 LENOVO TP-79 2190 INTL 20050513)
    [ 0.000000] ACPI: SSDT BFEF28B4, 00A6 (r1 LENOVO TP-79 2190 INTL 20050513)
    [ 0.000000] ACPI: SSDT BFEF295A, 04F7 (r1 LENOVO TP-79 2190 INTL 20050513)
    [ 0.000000] ACPI: SSDT BFEF2E51, 01D8 (r1 LENOVO TP-79 2190 INTL 20050513)
    [ 0.000000] (5 early reservations) ==> bootmem [0000000000 - 00bfed0000]
    [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
    [ 0.000000] #2 [0000200000 - 0000c2bc98] TEXT DATA BSS ==> [0000200000 - 0000c2bc98]
    [ 0.000000] #3 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
    [ 0.000000] #4 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000]
    [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes.
    [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes.
    [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes.
    [ 0.000000] found SMP MP-table at [ffff8800000f6810] 000f6810
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000000 -> 0x00001000
    [ 0.000000] DMA32 0x00001000 -> 0x00100000
    [ 0.000000] Normal 0x00100000 -> 0x00100000
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] early_node_map[2] active PFN ranges
    [ 0.000000] 0: 0x00000000 -> 0x0000009f
    [ 0.000000] 0: 0x00000100 -> 0x000bfed0
    [ 0.000000] On node 0 totalpages: 786031
    [ 0.000000] DMA zone: 1235 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 771340 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1008
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Setting APIC routing to flat
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] Allocating PCI resources starting at c4000000 (gap: c0000000:30000000)
    [ 0.000000] PERCPU: Allocating 435200 bytes of per cpu data
    [ 0.000000] NR_CPUS: 2, nr_cpu_ids: 2, nr_node_ids 1
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 772575
    [ 0.000000] Kernel command line: root=/dev/sda2 vga=0x365
    [ 0.000000] Initializing CPU#0
    [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
    [ 0.000000] Extended CMOS year: 2000
    [ 0.000000] TSC calibrated against PM_TIMER
    [ 0.000000] Detected 1828.742 MHz processor.
    [ 0.008000] Console: colour dummy device 80x25
    [ 0.008000] console [tty0] enabled
    [ 0.008000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
    [ 0.008000] ... MAX_LOCKDEP_SUBCLASSES: 8
    [ 0.008000] ... MAX_LOCK_DEPTH: 48
    [ 0.008000] ... MAX_LOCKDEP_KEYS: 2048
    [ 0.008000] ... CLASSHASH_SIZE: 1024
    [ 0.008000] ... MAX_LOCKDEP_ENTRIES: 8192
    [ 0.008000] ... MAX_LOCKDEP_CHAINS: 16384
    [ 0.008000] ... CHAINHASH_SIZE: 8192
    [ 0.008000] memory used by lock dependency info: 1840 kB
    [ 0.008000] per task-struct memory footprint: 3456 bytes
    [ 0.008000] ------------------------
    [ 0.008000] | Locking API testsuite:
    [ 0.008000] ----------------------------------------------------------------------------
    [ 0.008000] | spin |wlock |rlock |mutex | wsem | rsem |
    [ 0.008000] --------------------------------------------------------------------------
    [ 0.008000] A-A deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] double unlock: ok | ok | ok | ok | ok | ok |
    [ 0.008000] initialize held: ok | ok | ok | ok | ok | ok |
    [ 0.008000] bad unlock order: ok | ok | ok | ok | ok | ok |
    [ 0.008000] --------------------------------------------------------------------------
    [ 0.008000] recursive read-lock: | ok | | ok |
    [ 0.008000] recursive read-lock #2: | ok | | ok |
    [ 0.008000] mixed read-write-lock: | ok | | ok |
    [ 0.008000] mixed write-read-lock: | ok | | ok |
    [ 0.008000] --------------------------------------------------------------------------
    [ 0.008000] hard-irqs-on + irq-safe-A/12: ok | ok | ok |
    [ 0.008000] soft-irqs-on + irq-safe-A/12: ok | ok | ok |
    [ 0.008000] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
    [ 0.008000] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
    [ 0.008000] sirq-safe-A => hirqs-on/12: ok | ok | ok |
    [ 0.008000] sirq-safe-A => hirqs-on/21: ok | ok | ok |
    [ 0.008000] hard-safe-A + irqs-on/12: ok | ok | ok |
    [ 0.008000] soft-safe-A + irqs-on/12: ok | ok | ok |
    [ 0.008000] hard-safe-A + irqs-on/21: ok | ok | ok |
    [ 0.008000] soft-safe-A + irqs-on/21: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #1/132: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #1/132: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #1/213: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #1/213: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #1/231: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #1/231: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #1/312: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #1/312: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #1/321: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #1/321: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #2/123: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #2/123: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #2/132: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #2/132: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #2/213: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #2/213: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #2/231: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #2/231: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #2/312: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #2/312: ok | ok | ok |
    [ 0.008000] hard-safe-A + unsafe-B #2/321: ok | ok | ok |
    [ 0.008000] soft-safe-A + unsafe-B #2/321: ok | ok | ok |
    [ 0.008000] hard-irq lock-inversion/123: ok | ok | ok |
    [ 0.008000] soft-irq lock-inversion/123: ok | ok | ok |
    [ 0.008000] hard-irq lock-inversion/132: ok | ok | ok |
    [ 0.008000] soft-irq lock-inversion/132: ok | ok | ok |
    [ 0.008000] hard-irq lock-inversion/213: ok | ok | ok |
    [ 0.008000] soft-irq lock-inversion/213: ok | ok | ok |
    [ 0.008000] hard-irq lock-inversion/231: ok | ok | ok |
    [ 0.008000] soft-irq lock-inversion/231: ok | ok | ok |
    [ 0.008000] hard-irq lock-inversion/312: ok | ok | ok |
    [ 0.008000] soft-irq lock-inversion/312: ok | ok | ok |
    [ 0.008000] hard-irq lock-inversion/321: ok | ok | ok |
    [ 0.008000] soft-irq lock-inversion/321: ok | ok | ok |
    [ 0.008000] hard-irq read-recursion/123: ok |
    [ 0.008000] soft-irq read-recursion/123: ok |
    [ 0.008000] hard-irq read-recursion/132: ok |
    [ 0.008000] soft-irq read-recursion/132: ok |
    [ 0.008000] hard-irq read-recursion/213: ok |
    [ 0.008000] soft-irq read-recursion/213: ok |
    [ 0.008000] hard-irq read-recursion/231: ok |
    [ 0.008000] soft-irq read-recursion/231: ok |
    [ 0.008000] hard-irq read-recursion/312: ok |
    [ 0.008000] soft-irq read-recursion/312: ok |
    [ 0.008000] hard-irq read-recursion/321: ok |
    [ 0.008000] soft-irq read-recursion/321: ok |
    [ 0.008000] -------------------------------------------------------
    [ 0.008000] Good, all 218 testcases passed! |
    [ 0.008000] ---------------------------------
    [ 0.008000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.008000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.008000] Checking aperture...
    [ 0.008000] No AGP bridge found
    [ 0.008000] Memory: 3083172k/3144512k available (2670k kernel code, 60808k reserved, 1510k data, 648k init)
    [ 0.008000] CPA: page pool initialized 1 of 1 pages preallocated
    [ 0.008000] hpet clockevent registered
    [ 0.008000] Calibrating delay loop (skipped), value calculated using timer frequency.. <6>3657.48 BogoMIPS (lpj=7314968)
    [ 0.008000] Mount-cache hash table entries: 256
    [ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
    [ 0.008000] CPU: L2 cache: 2048K
    [ 0.008000] CPU: Physical Processor ID: 0
    [ 0.008000] CPU: Processor Core ID: 0
    [ 0.008000] CPU0: Thermal monitoring enabled (TM2)
    [ 0.008000] using mwait in idle threads.
    [ 0.008000] ACPI: Core revision 20080609
    [ 0.052003] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.092005] CPU0: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06
    [ 0.092005] Using local APIC timer interrupts.
    [ 0.096006] APIC timer calibration result 10390579
    [ 0.096006] Detected 10.390 MHz APIC timer.
    [ 0.096006] lockdep: fixing up alternatives.
    [ 0.096006] Booting processor 1/1 ip 6000
    [ 0.104006] Initializing CPU#1
    [ 0.184055] Calibrating delay using timer specific routine.. <6>3657.56 BogoMIPS (lpj=7315124)
    [ 0.184063] CPU: L1 I cache: 32K, L1 D cache: 32K
    [ 0.184065] CPU: L2 cache: 2048K
    [ 0.184068] CPU: Physical Processor ID: 0
    [ 0.184069] CPU: Processor Core ID: 1
    [ 0.184076] CPU1: Thermal monitoring enabled (TM2)
    [ 0.184756] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
    [ 0.186786] CPU1: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06
    [ 0.186847] checking TSC synchronization [CPU#0 -> CPU#1]:
    [ 0.188011] Measured 566258 cycles TSC warp between CPUs, turning off TSC clock.
    [ 0.188011] Marking TSC unstable due to check_tsc_sync_source failed
    [ 0.188068] Brought up 2 CPUs
    [ 0.188072] Total of 2 processors activated (7315.04 BogoMIPS).
    [ 0.188147] CPU0 attaching sched-domain:
    [ 0.188149] domain 0: span 0-1 level MC
    [ 0.188151] groups: 0 1
    [ 0.188162] CPU1 attaching sched-domain:
    [ 0.188163] domain 0: span 0-1 level MC
    [ 0.188164] groups: 1 0
    [ 0.188869] net_namespace: 1312 bytes
    [ 0.189191] NET: Registered protocol family 16
    [ 0.192523] ACPI: ACPI Dock Station Driver
    [ 0.193429] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    [ 0.193483] ACPI: bus type pci registered
    [ 0.194218] PCI: Using configuration type 1 for base access
    [ 0.210706] ACPI: EC: EC description table is found, configuring boot EC
    [ 0.240681] ACPI: EC: non-query interrupt received, switching to interrupt mode
    [ 0.254379] ACPI: Interpreter enabled
    [ 0.254387] ACPI: (supports S0 S3 S5)
    [ 0.254452] ACPI: Using IOAPIC for interrupt routing
    [ 0.289905] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
    [ 0.289915] ACPI: EC: driver started in interrupt mode
    [ 0.290289] ACPI: PCI Root Bridge [PCI0] (0000:00)
    [ 0.290810] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.290821] pci 0000:00:01.0: PME# disabled
    [ 0.291049] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.291061] pci 0000:00:1b.0: PME# disabled
    [ 0.291191] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.291202] pci 0000:00:1c.0: PME# disabled
    [ 0.291326] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.291338] pci 0000:00:1c.1: PME# disabled
    [ 0.291461] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.291472] pci 0000:00:1c.2: PME# disabled
    [ 0.291600] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.291611] pci 0000:00:1c.3: PME# disabled
    [ 0.292240] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.292253] pci 0000:00:1d.7: PME# disabled
    [ 0.292520] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
    [ 0.292533] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
    [ 0.292834] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.292845] pci 0000:00:1f.2: PME# disabled
    [ 0.293357] pci 0000:01:00.0: supports D1
    [ 0.293359] pci 0000:01:00.0: supports D2
    [ 0.293779] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 0.293793] pci 0000:02:00.0: PME# disabled
    [ 0.294365] pci 0000:03:00.0: PME# supported from D0 D3hot
    [ 0.294384] pci 0000:03:00.0: PME# disabled
    [ 0.294855] pci 0000:15:00.0: supports D1
    [ 0.294858] pci 0000:15:00.0: supports D2
    [ 0.294860] pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.294873] pci 0000:15:00.0: PME# disabled
    [ 0.294970] pci 0000:00:1e.0: transparent bridge
    [ 0.295114] bus 00 -> node 0
    [ 0.295129] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.295881] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    [ 0.296167] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
    [ 0.296502] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
    [ 0.296835] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
    [ 0.297175] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
    [ 0.297516] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
    [ 0.314373] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.314803] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.315230] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.315655] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.316091] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.316516] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.316944] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.317370] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
    [ 0.318429] ACPI: Power Resource [PUBS] (on)
    [ 0.319018] Linux Plug and Play Support v0.97 (c) Adam Belay
    [ 0.319191] pnp: PnP ACPI init
    [ 0.319234] ACPI: bus type pnp registered
    [ 0.330068] pnp: PnP ACPI: found 12 devices
    [ 0.330078] ACPI: ACPI bus type pnp unregistered
    [ 0.331122] SCSI subsystem initialized
    [ 0.331372] libata version 3.00 loaded.
    [ 0.331956] usbcore: registered new interface driver usbfs
    [ 0.332332] usbcore: registered new interface driver hub
    [ 0.332581] usbcore: registered new device driver usb
    [ 0.333462] PCI: Using ACPI for IRQ routing
    [ 0.352014] PCI-GART: No AMD northbridge found.
    [ 0.352027] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.352037] hpet0: 3 64-bit timers, 14318180 Hz
    [ 0.355932] Switched to high resolution mode on CPU 0
    [ 0.356589] Switched to high resolution mode on CPU 1
    [ 0.367960] system 00:00: iomem range 0x0-0x9ffff could not be reserved
    [ 0.367970] system 00:00: iomem range 0xc0000-0xc3fff has been reserved
    [ 0.367980] system 00:00: iomem range 0xc4000-0xc7fff has been reserved
    [ 0.367989] system 00:00: iomem range 0xc8000-0xcbfff has been reserved
    [ 0.367998] system 00:00: iomem range 0xcc000-0xcffff has been reserved
    [ 0.368007] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
    [ 0.368017] system 00:00: iomem range 0xdc000-0xdffff could not be reserved
    [ 0.368027] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
    [ 0.368037] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
    [ 0.368046] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
    [ 0.368056] system 00:00: iomem range 0xec000-0xeffff could not be reserved
    [ 0.368065] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
    [ 0.368075] system 00:00: iomem range 0x100000-0xbfffffff could not be reserved
    [ 0.368086] system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
    [ 0.368096] system 00:00: iomem range 0xfed41000-0xffffffff could not be reserved
    [ 0.368128] system 00:02: ioport range 0x164e-0x164f has been reserved
    [ 0.368137] system 00:02: ioport range 0x1000-0x107f has been reserved
    [ 0.368146] system 00:02: ioport range 0x1180-0x11bf has been reserved
    [ 0.368155] system 00:02: ioport range 0x800-0x80f has been reserved
    [ 0.368163] system 00:02: ioport range 0x15e0-0x15ef has been reserved
    [ 0.368173] system 00:02: ioport range 0x1600-0x165f could not be reserved
    [ 0.368183] system 00:02: iomem range 0xf0000000-0xf3ffffff could not be reserved
    [ 0.368194] system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved
    [ 0.368205] system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
    [ 0.368215] system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
    [ 0.368226] system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
    [ 0.371100] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    [ 0.371110] pci 0000:00:01.0: IO window: 0x2000-0x2fff
    [ 0.371121] pci 0000:00:01.0: MEM window: 0xee100000-0xee1fffff
    [ 0.371132] pci 0000:00:01.0: PREFETCH window: 0x000000d8000000-0x000000dfffffff
    [ 0.371147] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
    [ 0.371156] pci 0000:00:1c.0: IO window: 0x3000-0x3fff
    [ 0.371169] pci 0000:00:1c.0: MEM window: 0xee000000-0xee0fffff
    [ 0.371180] pci 0000:00:1c.0: PREFETCH window: disabled
    [ 0.371196] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
    [ 0.371205] pci 0000:00:1c.1: IO window: 0x4000-0x5fff
    [ 0.371218] pci 0000:00:1c.1: MEM window: 0xec000000-0xedffffff
    [ 0.371230] pci 0000:00:1c.1: PREFETCH window: 0x000000e4000000-0x000000e40fffff
    [ 0.371248] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
    [ 0.371257] pci 0000:00:1c.2: IO window: 0x6000-0x7fff
    [ 0.371270] pci 0000:00:1c.2: MEM window: 0xe8000000-0xe9ffffff
    [ 0.371281] pci 0000:00:1c.2: PREFETCH window: 0x000000e4100000-0x000000e41fffff
    [ 0.371299] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0c
    [ 0.371308] pci 0000:00:1c.3: IO window: 0x8000-0x9fff
    [ 0.371321] pci 0000:00:1c.3: MEM window: 0xea000000-0xebffffff
    [ 0.371332] pci 0000:00:1c.3: PREFETCH window: 0x000000e4200000-0x000000e42fffff
    [ 0.371357] pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
    [ 0.371364] pci 0000:15:00.0: IO window: 0x00a000-0x00a0ff
    [ 0.371377] pci 0000:15:00.0: IO window: 0x00a400-0x00a4ff
    [ 0.371389] pci 0000:15:00.0: PREFETCH window: 0xe0000000-0xe3ffffff
    [ 0.371402] pci 0000:15:00.0: MEM window: 0xc4000000-0xc7ffffff
    [ 0.371414] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
    [ 0.371423] pci 0000:00:1e.0: IO window: 0xa000-0xdfff
    [ 0.371436] pci 0000:00:1e.0: MEM window: 0xe4300000-0xe7ffffff
    [ 0.371448] pci 0000:00:1e.0: PREFETCH window: 0x000000e0000000-0x000000e3ffffff
    [ 0.371483] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.371494] pci 0000:00:01.0: setting latency timer to 64
    [ 0.371512] pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [ 0.371523] pci 0000:00:1c.0: setting latency timer to 64
    [ 0.371541] pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    [ 0.371553] pci 0000:00:1c.1: setting latency timer to 64
    [ 0.371570] pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    [ 0.371582] pci 0000:00:1c.2: setting latency timer to 64
    [ 0.371599] pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
    [ 0.371611] pci 0000:00:1c.3: setting latency timer to 64
    [ 0.371620] pci 0000:00:1e.0: enabling device (0005 -> 0007)
    [ 0.371633] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.371651] pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.371789] NET: Registered protocol family 2
    [ 0.416233] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.418053] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    [ 0.421280] TCP bind hash table entries: 65536 (order: 10, 4194304 bytes)
    [ 0.427554] TCP: Hash tables configured (established 262144 bind 65536)
    [ 0.427616] TCP reno registered
    [ 0.436315] NET: Registered protocol family 1
    [ 0.436982] Simple Boot Flag at 0x35 set to 0x1
    [ 0.443600] msgmni has been set to 6022
    [ 0.444134] io scheduler noop registered
    [ 0.444205] io scheduler cfq registered (default)
    [ 0.444258] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x2000
    [ 0.444261] pci 0000:00:1d.0: Performing full reset
    [ 0.444286] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x2000
    [ 0.444289] pci 0000:00:1d.1: Performing full reset
    [ 0.444314] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x2000
    [ 0.444316] pci 0000:00:1d.2: Performing full reset
    [ 0.444340] pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x2000
    [ 0.444343] pci 0000:00:1d.3: Performing full reset
    [ 0.444427] pci 0000:01:00.0: Boot video device
    [ 0.444888] pcieport-driver 0000:00:01.0: setting latency timer to 64
    [ 0.444971] pcieport-driver 0000:00:01.0: found MSI capability
    [ 0.445010] pci_express 0000:00:01.0cie00: allocate port service
    [ 0.445281] pcieport-driver 0000:00:1c.0: setting latency timer to 64
    [ 0.445355] pcieport-driver 0000:00:1c.0: found MSI capability
    [ 0.445449] pci_express 0000:00:1c.0cie00: allocate port service
    [ 0.445655] pci_express 0000:00:1c.0cie02: allocate port service
    [ 0.445989] pcieport-driver 0000:00:1c.1: setting latency timer to 64
    [ 0.446063] pcieport-driver 0000:00:1c.1: found MSI capability
    [ 0.446149] pci_express 0000:00:1c.1cie00: allocate port service
    [ 0.446348] pci_express 0000:00:1c.1cie02: allocate port service
    [ 0.446668] pcieport-driver 0000:00:1c.2: setting latency timer to 64
    [ 0.446742] pcieport-driver 0000:00:1c.2: found MSI capability
    [ 0.446829] pci_express 0000:00:1c.2cie00: allocate port service
    [ 0.447026] pci_express 0000:00:1c.2cie02: allocate port service
    [ 0.447344] pcieport-driver 0000:00:1c.3: setting latency timer to 64
    [ 0.447419] pcieport-driver 0000:00:1c.3: found MSI capability
    [ 0.447506] pci_express 0000:00:1c.3cie00: allocate port service
    [ 0.447724] pci_express 0000:00:1c.3cie02: allocate port service
    [ 0.449189] vesafb: framebuffer at 0xd8000000, mapped to 0xffffc20000080000, using 5120k, total 16384k
    [ 0.449199] vesafb: mode is 1280x1024x16, linelength=2560, pages=5
    [ 0.449206] vesafb: scrolling: redraw
    [ 0.449211] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    [ 0.493549] Console: switching to colour frame buffer device 160x64
    [ 0.536509] fb0: VESA VGA frame buffer device
    [ 0.665719] Real Time Clock Driver v1.12ac
    [ 0.666310] hpet_resources: 0xfed00000 is busy
    [ 0.666908] Non-volatile memory driver v1.2
    [ 0.667117] Linux agpgart interface v0.103
    [ 0.667321] Serial: 8250/16550 driver4 ports, IRQ sharing disabled
    [ 0.674508] loop: module loaded
    [ 0.674673] tun: Universal TUN/TAP device driver, 1.6
    [ 0.674922] tun: (C) 1999-2004 Max Krasnyansky
    [ 0.675515] Uniform Multi-Platform E-IDE driver
    [ 0.676185] piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02)
    [ 0.676521] pci 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
    [ 0.676867] piix 0000:00:1f.1: IDE port disabled
    [ 0.677141] piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    [ 0.677484] ide0: BM-DMA at 0x1880-0x1887
    [ 0.677705] Probing IDE interface ide0...
    [ 1.412234] hda: MAT****ADVD-RAM UJ-842, ATAPI CD/DVD-ROM drive
    [ 1.748159] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
    [ 1.748490] hda: UDMA/33 mode selected
    [ 1.749103] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    [ 1.752577] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
    [ 1.753068] ide_generic: I/O resource 0x1F0-0x1F7 not free.
    [ 1.753344] ide_generic: I/O resource 0x170-0x177 not free.
    [ 1.754966] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
    [ 1.755380] Uniform CD-ROM driver Revision: 3.20
    [ 1.760195] Driver 'sd' needs updating - please use bus_type methods
    [ 1.760927] ahci 0000:00:1f.2: version 3.0
    [ 1.760947] ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
    [ 1.761689] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
    [ 1.762094] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
    [ 1.762432] ahci 0000:00:1f.2: setting latency timer to 64
    [ 1.762676] scsi0 : ahci
    [ 1.763352] scsi1 : ahci
    [ 1.763849] scsi2 : ahci
    [ 1.764396] scsi3 : ahci
    [ 1.764971] ata1: SATA max UDMA/133 abar m1024@0xee404400 port 0xee404500 irq 218
    [ 1.765336] ata2: DUMMY
    [ 1.765460] ata3: DUMMY
    [ 1.765584] ata4: DUMMY
    [ 2.307894] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.309799] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
    [ 2.309803] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
    [ 2.310096] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
    [ 2.311458] ata1.00: ATA-7: HTS541080G9SA00, MB4IC60R, max UDMA/100
    [ 2.311767] ata1.00: 156301488 sectors, multi 16: LBA48
    [ 2.322252] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
    [ 2.322256] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
    [ 2.331205] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
    [ 2.341281] ata1.00: configured for UDMA/100
    [ 2.352758] ata1.00: configured for UDMA/100
    [ 2.361818] ata1: EH complete
    [ 2.371746] scsi 0:0:0:0: Direct-Access ATA HTS541080G9SA00 MB4I PQ: 0 ANSI: 5
    [ 2.382421] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
    [ 2.392439] sd 0:0:0:0: [sda] Write Protect is off
    [ 2.402507] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.402596] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.413746] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
    [ 2.424540] sd 0:0:0:0: [sda] Write Protect is off
    [ 2.435405] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.435494] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.446903] sda: sda1 sda2 sda3 < sda5 >
    [ 2.908058] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 2.920824] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [ 2.933329] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
    [ 2.934411] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
    [ 2.946569] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [ 2.958815] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 2.958820] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 2.972043] drivers/usb/core/inode.c: creating file 'devices'
    [ 2.972118] drivers/usb/core/inode.c: creating file '001'
    [ 2.972760] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    [ 2.985549] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
    [ 2.985555] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
    [ 2.985631] ehci_hcd 0000:00:1d.7: reset command 080022 (park)=0 ithresh=8 Async period=1024 Reset HALT
    [ 2.989541] ehci_hcd 0000:00:1d.7: debug port 1
    [ 3.002322] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    [ 3.002325] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
    [ 3.002355] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xee404000
    [ 3.015382] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
    [ 3.019277] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
    [ 3.027874] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    [ 3.041366] usb usb1: default language 0x0409
    [ 3.041566] usb usb1: uevent
    [ 3.041734] usb usb1: usb_probe_device
    [ 3.041737] usb usb1: configuration #1 chosen from 1 choice
    [ 3.055273] usb usb1: adding 1-0:1.0 (config #1, interface 0)
    [ 3.055355] usb 1-0:1.0: uevent
    [ 3.055571] hub 1-0:1.0: usb_probe_interface
    [ 3.055574] hub 1-0:1.0: usb_probe_interface - got id
    [ 3.055578] hub 1-0:1.0: USB hub found
    [ 3.069009] hub 1-0:1.0: 8 ports detected
    [ 3.082231] hub 1-0:1.0: standalone hub
    [ 3.082233] hub 1-0:1.0: no power switching (usb 1.0)
    [ 3.082235] hub 1-0:1.0: individual port over-current protection
    [ 3.082237] hub 1-0:1.0: power on to power good time: 20ms
    [ 3.082360] hub 1-0:1.0: local power source is good
    [ 3.082364] hub 1-0:1.0: trying to enable port power on non-switchable hub
    [ 3.183882] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
    [ 3.183890] hub 1-0:1.0: port 1: status 0501 change 0001
    [ 3.183909] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
    [ 3.183917] hub 1-0:1.0: port 2: status 0501 change 0001
    [ 3.183982] ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001803 POWER sig=j CSC CONNECT
    [ 3.183990] hub 1-0:1.0: port 8: status 0501 change 0001
    [ 3.288102] hub 1-0:1.0: state 7 ports 8 chg 0106 evt 0000
    [ 3.288869] drivers/usb/core/inode.c: creating file '001'
    [ 3.289180] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
    [ 3.289278] ehci_hcd 0000:00:1d.7: port 1 low speed --> companion
    [ 3.289352] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [ 3.302803] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 3.316331] usb usb1: Product: EHCI Host Controller
    [ 3.329858] usb usb1: Manufacturer: Linux 2.6.27-rc1-dirty ehci_hcd
    [ 3.343400] usb usb1: SerialNumber: 0000:00:1d.7
    [ 3.356988] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
    [ 3.357095] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
    [ 3.357114] ehci_hcd 0000:00:1d.7: port 2 low speed --> companion
    [ 3.357284] USB Universal Host Controller Interface driver v3.0
    [ 3.371569] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
    [ 3.385173] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 3.398627] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 3.398632] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 3.412228] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
    [ 3.412293] hub 1-0:1.0: port 8, status 0501, change 0000, 480 Mb/s
    [ 3.412341] drivers/usb/core/inode.c: creating file '002'
    [ 3.412690] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 3.426211] uhci_hcd 0000:00:1d.0: detected 2 ports
    [ 3.439570] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
    [ 3.439573] uhci_hcd 0000:00:1d.0: Performing full reset
    [ 3.439592] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
    [ 3.439621] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001800
    [ 3.453086] usb usb2: default language 0x0409
    [ 3.453278] usb usb2: uevent
    [ 3.453430] usb usb2: usb_probe_device
    [ 3.453433] usb usb2: configuration #1 chosen from 1 choice
    [ 3.466610] usb usb2: adding 2-0:1.0 (config #1, interface 0)
    [ 3.466685] usb 2-0:1.0: uevent
    [ 3.466834] hub 2-0:1.0: usb_probe_interface
    [ 3.466836] hub 2-0:1.0: usb_probe_interface - got id
    [ 3.466840] hub 2-0:1.0: USB hub found
    [ 3.480051] hub 2-0:1.0: 2 ports detected
    [ 3.493090] hub 2-0:1.0: standalone hub
    [ 3.493092] hub 2-0:1.0: no power switching (usb 1.0)
    [ 3.493094] hub 2-0:1.0: individual port over-current protection
    [ 3.493096] hub 2-0:1.0: power on to power good time: 2ms
    [ 3.493135] hub 2-0:1.0: local power source is good
    [ 3.493139] hub 2-0:1.0: trying to enable port power on non-switchable hub
    [ 3.493421] ehci_hcd 0000:00:1d.7: port 8 full speed --> companion
    [ 3.493426] ehci_hcd 0000:00:1d.7: GetStatus port 8 status 003801 POWER OWNER sig=j CONNECT
    [ 3.493433] hub 1-0:1.0: port 8 not reset yet, waiting 50ms
    [ 3.547875] ehci_hcd 0000:00:1d.7: GetStatus port 8 status 003002 POWER OWNER sig=se0 CSC
    [ 3.547924] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0100
    [ 3.595877] uhci_hcd 0000:00:1d.0: port 1 portsc 01ab,00
    [ 3.595884] hub 2-0:1.0: port 1: status 0301 change 0003
    [ 3.595914] uhci_hcd 0000:00:1d.0: port 2 portsc 01ab,00
    [ 3.595921] hub 2-0:1.0: port 2: status 0301 change 0003
    [ 3.700086] hub 2-0:1.0: state 7 ports 2 chg 0006 evt 0000
    [ 3.700347] drivers/usb/core/inode.c: creating file '001'
    [ 3.700607] hub 2-0:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
    [ 3.700674] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
    [ 3.713942] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 3.727052] usb usb2: Product: UHCI Host Controller
    [ 3.739941] usb usb2: Manufacturer: Linux 2.6.27-rc1-dirty uhci_hcd
    [ 3.753081] usb usb2: SerialNumber: 0000:00:1d.0
    [ 3.766159] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 3.779192] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 3.779197] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 3.792418] drivers/usb/core/inode.c: creating file '003'
    [ 3.792706] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    [ 3.805745] uhci_hcd 0000:00:1d.1: detected 2 ports
    [ 3.818598] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
    [ 3.818601] uhci_hcd 0000:00:1d.1: Performing full reset
    [ 3.818618] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
    [ 3.818645] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001820
    [ 3.831549] usb usb3: default language 0x0409
    [ 3.831733] usb usb3: uevent
    [ 3.831936] usb usb3: usb_probe_device
    [ 3.831939] usb usb3: configuration #1 chosen from 1 choice
    [ 3.844379] usb usb3: adding 3-0:1.0 (config #1, interface 0)
    [ 3.844455] usb 3-0:1.0: uevent
    [ 3.844605] hub 3-0:1.0: usb_probe_interface
    [ 3.844607] hub 3-0:1.0: usb_probe_interface - got id
    [ 3.844611] hub 3-0:1.0: USB hub found
    [ 3.857438] hub 3-0:1.0: 2 ports detected
    [ 3.870339] hub 3-0:1.0: standalone hub
    [ 3.870342] hub 3-0:1.0: no power switching (usb 1.0)
    [ 3.870344] hub 3-0:1.0: individual port over-current protection
    [ 3.870346] hub 3-0:1.0: power on to power good time: 2ms
    [ 3.870366] hub 3-0:1.0: local power source is good
    [ 3.870369] hub 3-0:1.0: trying to enable port power on non-switchable hub
    [ 3.870401] usb 2-1: new low speed USB device using uhci_hcd and address 2
    [ 3.972364] drivers/usb/core/inode.c: creating file '001'
    [ 3.972665] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
    [ 3.985880] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 3.999032] usb usb3: Product: UHCI Host Controller
    [ 4.012292] usb usb3: Manufacturer: Linux 2.6.27-rc1-dirty uhci_hcd
    [ 4.025826] usb usb3: SerialNumber: 0000:00:1d.1
    [ 4.039823] uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
    [ 4.053379] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    [ 4.066977] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 4.066982] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 4.080830] drivers/usb/core/inode.c: creating file '004'
    [ 4.081160] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    [ 4.094893] uhci_hcd 0000:00:1d.2: detected 2 ports
    [ 4.108502] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
    [ 4.108505] uhci_hcd 0000:00:1d.2: Performing full reset
    [ 4.108523] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
    [ 4.108550] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
    [ 4.122803] usb 2-1: skipped 1 descriptor after interface
    [ 4.122430] usb usb4: default language 0x0409
    [ 4.122613] usb usb4: uevent
    [ 4.122764] usb usb4: usb_probe_device
    [ 4.122767] usb usb4: configuration #1 chosen from 1 choice
    [ 4.136350] usb usb4: adding 4-0:1.0 (config #1, interface 0)
    [ 4.136424] usb 4-0:1.0: uevent
    [ 4.136582] hub 4-0:1.0: usb_probe_interface
    [ 4.136584] hub 4-0:1.0: usb_probe_interface - got id
    [ 4.136588] hub 4-0:1.0: USB hub found
    [ 4.150962] usb 2-1: default language 0x0409
    [ 4.150481] hub 4-0:1.0: 2 ports detected
    [ 4.164343] hub 4-0:1.0: standalone hub
    [ 4.164345] hub 4-0:1.0: no power switching (usb 1.0)
    [ 4.164347] hub 4-0:1.0: individual port over-current protection
    [ 4.164350] hub 4-0:1.0: power on to power good time: 2ms
    [ 4.164369] hub 4-0:1.0: local power source is good
    [ 4.164373] hub 4-0:1.0: trying to enable port power on non-switchable hub
    [ 4.172212] usb 2-1: uevent
    [ 4.172368] usb 2-1: usb_probe_device
    [ 4.172370] usb 2-1: configuration #1 chosen from 1 choice
    [ 4.189060] usb 2-1: adding 2-1:1.0 (config #1, interface 0)
    [ 4.189138] usb 2-1:1.0: uevent
    [ 4.189739] drivers/usb/core/inode.c: creating file '002'
    [ 4.190031] usb 2-1: New USB device found, idVendor=413c, idProduct=2003
    [ 4.203837] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
    [ 4.217656] usb 2-1: Product: Dell USB Keyboard
    [ 4.231320] usb 2-1: Manufacturer: Dell
    [ 4.244793] hub 2-0:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
    [ 4.264361] drivers/usb/core/inode.c: creating file '001'
    [ 4.264659] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
    [ 4.278306] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 4.291877] usb usb4: Product: UHCI Host Controller
    [ 4.305235] usb usb4: Manufacturer: Linux 2.6.27-rc1-dirty uhci_hcd
    [ 4.318701] usb usb4: SerialNumber: 0000:00:1d.2
    [ 4.332169] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [ 4.345698] uhci_hcd 0000:00:1d.3: setting latency timer to 64
    [ 4.345703] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 4.359390] drivers/usb/core/inode.c: creating file '005'
    [ 4.359678] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    [ 4.373367] usb 2-2: new low speed USB device using uhci_hcd and address 3
    [ 4.386997] uhci_hcd 0000:00:1d.3: detected 2 ports
    [ 4.400658] uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
    [ 4.400660] uhci_hcd 0000:00:1d.3: Performing full reset
    [ 4.400687] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001860
    [ 4.414500] usb usb5: default language 0x0409
    [ 4.414685] usb usb5: uevent
    [ 4.414835] usb usb5: usb_probe_device
    [ 4.414838] usb usb5: configuration #1 chosen from 1 choice
    [ 4.428520] usb usb5: adding 5-0:1.0 (config #1, interface 0)
    [ 4.428602] usb 5-0:1.0: uevent
    [ 4.428760] hub 5-0:1.0: usb_probe_interface
    [ 4.428763] hub 5-0:1.0: usb_probe_interface - got id
    [ 4.428766] hub 5-0:1.0: USB hub found
    [ 4.442319] hub 5-0:1.0: 2 ports detected
    [ 4.455727] hub 5-0:1.0: standalone hub
    [ 4.455729] hub 5-0:1.0: no power switching (usb 1.0)
    [ 4.455731] hub 5-0:1.0: individual port over-current protection
    [ 4.455734] hub 5-0:1.0: power on to power good time: 2ms
    [ 4.455753] hub 5-0:1.0: local power source is good
    [ 4.455757] hub 5-0:1.0: trying to enable port power on non-switchable hub
    [ 4.546074] usb 2-2: skipped 1 descriptor after interface
    [ 4.551064] usb 2-2: default language 0x0409
    [ 4.555887] uhci_hcd 0000:00:1d.3: port 2 portsc 009b,00
    [ 4.555895] hub 5-0:1.0: port 2: status 0101 change 0003
    [ 4.568218] usb 2-2: uevent
    [ 4.568371] usb 2-2: usb_probe_device
    [ 4.568374] usb 2-2: configuration #1 chosen from 1 choice
    [ 4.584062] usb 2-2: adding 2-2:1.0 (config #1, interface 0)
    [ 4.584139] usb 2-2:1.0: uevent
    [ 4.584728] drivers/usb/core/inode.c: creating file '003'
    [ 4.585031] usb 2-2: New USB device found, idVendor=045e, idProduct=0084
    [ 4.598638] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
    [ 4.612258] usb 2-2: Product: Basic Optical Mouse
    [ 4.625802] usb 2-2: Manufacturer: Microsoft
    [ 4.639210] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    [ 4.639219] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    [ 4.660149] hub 5-0:1.0: state 7 ports 2 chg 0004 evt 0000
    [ 4.660423] drivers/usb/core/inode.c: creating file '001'
    [ 4.660685] hub 5-0:1.0: port 2, status 0101, change 0000, 12 Mb/s
    [ 4.660743] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
    [ 4.674326] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 4.687902] usb usb5: Product: UHCI Host Controller
    [ 4.701374] usb usb5: Manufacturer: Linux 2.6.27-rc1-dirty uhci_hcd
    [ 4.714932] usb usb5: SerialNumber: 0000:00:1d.3
    [ 4.729126] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    [ 4.749986] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 4.763694] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 4.777837] mice: PS/2 mouse device common for all mice
    [ 4.791514] usb 5-2: new full speed USB device using uhci_hcd and address 2
    [ 4.816031] usbhid 2-1:1.0: usb_probe_interface
    [ 4.816034] usbhid 2-1:1.0: usb_probe_interface - got id
    [ 4.810205] input: AT Translated Set 2 keyboard as /class/input/input0
    [ 4.824973] input: Dell Dell USB Keyboard as /class/input/input1
    [ 4.879933] uhci_hcd 0000:00:1d.0: reserve dev 2 ep81-INT, period 16, phase 8, 118 us
    [ 4.892390] input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1
    [ 4.906618] usbhid 2-2:1.0: usb_probe_interface
    [ 4.906621] usbhid 2-2:1.0: usb_probe_interface - got id
    [ 4.919777] input: Microsoft Basic Optical Mouse as /class/input/input2
    [ 4.955854] usb 5-2: ep0 maxpacket = 8
    [ 4.964289] input,hidraw1: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.0-2
    [ 4.991484] usb 5-2: default language 0x0409
    [ 5.010635] usb 5-2: uevent
    [ 5.010802] usb 5-2: usb_probe_device
    [ 5.010805] usb 5-2: configuration #1 chosen from 1 choice
    [ 5.027481] usb 5-2: adding 5-2:1.0 (config #1, interface 0)
    [ 5.027559] usb 5-2:1.0: uevent
    [ 5.028720] drivers/usb/core/inode.c: creating file '002'
    [ 5.029026] usb 5-2: New USB device found, idVendor=0483, idProduct=2016
    [ 5.043468] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
    [ 5.057907] usb 5-2: Product: Biometric Coprocessor
    [ 5.072283] usb 5-2: Manufacturer: STMicroelectronics
    [ 5.086890] usbcore: registered new interface driver usbhid
    [ 5.101355] usbhid: v2.6:USB HID core driver
    [ 5.115869] usb usb3: suspend_rh (auto-stop)
    [ 5.116066] Advanced Linux Sound Architecture Driver Version 1.0.17.
    [ 5.131217] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 5.145978] hda_intel: probe_mask set to 0x1 for device 17aa:2010
    [ 5.160748] HDA Intel 0000:00:1b.0: setting latency timer to 64
    [ 5.228773] ALSA device list:
    [ 5.243297] #0: HDA Intel at 0xee400000 irq 17
    [ 5.258403] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
    [ 5.275944] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 5.290681] TCP cubic registered
    [ 5.305219] NET: Registered protocol family 17
    [ 5.363868] usb usb4: suspend_rh (auto-stop)
    [ 5.648200] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04793/0x300000
    [ 5.663023] serio: Synaptics pass-through port at isa0060/serio1/input0
    [ 5.720662] input: SynPS/2 Synaptics TouchPad as /class/input/input3
    [ 5.819961] hub 1-0:1.0: hub_suspend
    [ 5.820022] usb usb1: bus auto-suspend
    [ 5.820024] ehci_hcd 0000:00:1d.7: suspend root hub
    [ 6.819832] hub 3-0:1.0: hub_suspend
    [ 6.819841] usb usb3: bus auto-suspend
    [ 6.819852] usb usb3: suspend_rh
    [ 6.819876] hub 4-0:1.0: hub_suspend
    [ 6.819884] usb usb4: bus auto-suspend
    [ 6.819886] usb usb4: suspend_rh
    [ 11.214743] IBM TrackPoint firmware: 0x0e, buttons: 3/3
    [ 11.465919] input: TPPS/2 IBM TrackPoint as /class/input/input4
    [ 12.123537] kjournald starting. Commit interval 5 seconds
    [ 12.133441] EXT3-fs: mounted filesystem with ordered data mode.
    [ 12.133528] VFS: Mounted root (ext3 filesystem) readonly.
    [ 12.133581] Freeing unused kernel memory: 648k freed
    [ 12.134010] Write protecting the kernel read-only data: 3864k
    [ 14.592401] usb usb2: uevent
    [ 14.592490] usb 2-0:1.0: uevent
    [ 14.592571] usb 2-1: uevent
    [ 14.592652] usb 2-1:1.0: uevent
    [ 14.592733] usb 2-2: uevent
    [ 14.592813] usb 2-2:1.0: uevent
    [ 14.592969] usb usb3: uevent
    [ 14.593061] usb 3-0:1.0: uevent
    [ 14.593216] usb usb4: uevent
    [ 14.593310] usb 4-0:1.0: uevent
    [ 14.593463] usb usb5: uevent
    [ 14.593542] usb 5-0:1.0: uevent
    [ 14.593630] usb 5-2: uevent
    [ 14.593709] usb 5-2:1.0: uevent
    [ 14.593863] usb usb1: uevent
    [ 14.593942] usb 1-0:1.0: uevent
    [ 15.629102] thinkpad_acpi: ThinkPad ACPI Extras v0.21
    [ 15.644564] thinkpad_acpi: http://ibm-acpi.sf.net/
    [ 15.660043] thinkpad_acpi: ThinkPad BIOS 79ETD9WW (2.19 ), EC 79HT50WW-1.07
    [ 15.675596] thinkpad_acpi: Lenovo ThinkPad T60, model 2007FUG
    [ 15.696791] thinkpad_acpi: radio switch found; radios are disabled
    [ 15.712954] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
    [ 15.729162] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
    [ 15.759763] thinkpad_acpi: setting the hotkey mask to 0xffffffff is likely not the best way to go about it
    [ 15.773022] thinkpad_acpi: please consider using the driver defaults, and refer to up-to-date thinkpad-acpi documentation
    [ 15.800931] thinkpad_acpi: requested hot key mask 0xffffffff, but firmware forced it to 0x00ffffff
    [ 15.834003] input: Power Button (FF) as /class/input/input5
    [ 15.854397] Registered led device: tpacpi::thinklight
    [ 15.871542] Registered led device: tpacpi:ower
    [ 15.922968] Registered led device: tpacpirange:batt
    [ 15.940093] ACPI: Power Button (FF) [PWRF]
    [ 15.968313] ACPI: SSDT BFEF1D36, 0240 (r1 PmRef Cpu0Ist 100 INTL 20050513)
    [ 15.962334] Registered led device: tpacpi:green:batt
    [ 15.962420] Registered led device: tpacpi::dock_active
    [ 15.962497] Registered led device: tpacpi::bay_active
    [ 15.962576] Registered led device: tpacpi::dock_batt
    [ 15.962652] Registered led device: tpacpi::unknown_led
    [ 15.962729] Registered led device: tpacpi::standby
    [ 16.091931] ACPI: SSDT BFEF1FFB, 065A (r1 PmRef Cpu0Cst 100 INTL 20050513)
    [ 16.134011] thinkpad_acpi: Lenovo BIOS switched to ACPI backlight control mode
    [ 16.133230] Monitor-Mwait will be used to enter C-1 state
    [ 16.133234] Monitor-Mwait will be used to enter C-2 state
    [ 16.133238] Monitor-Mwait will be used to enter C-3 state
    [ 16.133247] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    [ 16.133486] processor ACPI0007:00: registered as cooling_device0
    [ 16.133500] ACPI: Processor [CPU0] (supports 8 throttling states)
    [ 16.133828] input: Lid Switch as /class/input/input6
    [ 16.134873] ACPI: SSDT BFEF1C6E, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513)
    [ 16.137360] ACPI: SSDT BFEF1F76, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513)
    [ 16.245657] thinkpad_acpi: standard ACPI backlight interface available, not loading native one...
    [ 16.265543] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
    [ 16.281850] processor ACPI0007:01: registered as cooling_device1
    [ 16.289251] input: ThinkPad Extra Buttons as /class/input/input7
    [ 16.313748] ACPI: Processor [CPU1] (supports 8 throttling states)
    [ 16.318584] ACPI: Lid Switch [LID]
    [ 16.318795] input: Sleep Button (CM) as /class/input/input8
    [ 16.448255] ACPI: Sleep Button (CM) [SLPB]
    [ 16.473867] thermal LNXTHERM:01: registered as thermal_zone0
    [ 16.508369] ACPI: Thermal Zone [THM0] (55 C)
    [ 16.531612] thermal LNXTHERM:02: registered as thermal_zone1
    [ 16.555197] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
    [ 16.555688] ACPI: Thermal Zone [THM1] (59 C)
    [ 16.588158] e1000e: Copyright (c) 1999-2008 Intel Corporation.
    [ 16.597494] ACPI: Battery Slot [BAT0] (battery present)
    [ 16.614661] ACPI: AC Adapter [AC] (on-line)
    [ 16.627695] e1000e 0000:02:00.0: Disabling L1 ASPM
    [ 16.627722] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 16.627740] e1000e 0000:02:00.0: setting latency timer to 64
    [ 16.772729] eth0: (PCI Express:2.5GB/s:Width x1) 00:16:41:e3:2c:76
    [ 16.772744] eth0: Intel(R) PRO/1000 Network Connection
    [ 16.787449] eth0: MAC: 2, PHY: 2, PBA No: 005301-003
    [ 17.000384] Clocksource tsc unstable (delta = -83680835 ns)
    [ 17.275465] Adding 1542196k swap on /dev/sda1. Priority:-1 extents:1 across:1542196k
    [ 18.048345] EXT3 FS on sda2, internal journal
    [ 20.135666] kjournald starting. Commit interval 5 seconds
    [ 20.150924] EXT3 FS on sda5, internal journal
    [ 20.162201] EXT3-fs: mounted filesystem with ordered data mode.
    [ 20.269734] warning: `mount' uses 32-bit capabilities (legacy support in use)
    [ 20.406420] fuse init (API version 7.9)
    [ 24.251386] IA-32 Microcode Update Driver: v1.14a
    [ 24.251829] firmware: requesting intel-ucode/06-0f-06
    [ 24.327974] firmware: requesting intel-ucode/06-0f-06
    [ 37.544652] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [ 37.544657] eth0: 10/100 speed: disabling TSO
    [ 38.076133] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 93 us
    [ 38.095682] uhci_hcd 0000:00:1d.0: release dev 3 ep81-INT, period 8, phase 4, 93 us
    [ 38.248746] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 93 us
    [ 38.268167] uhci_hcd 0000:00:1d.0: release dev 3 ep81-INT, period 8, phase 4, 93 us
    [ 38.835458] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 93 us
    [ 47.257737] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 47.391952] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [ 47.431286] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=245 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=225
    [ 47.647293] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [ 47.906035] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [ 54.267233] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 62.281825] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 77.375600] CPU0 attaching NULL sched-domain.
    [ 77.375705] CPU1 attaching NULL sched-domain.
    [ 77.389339] CPU0 attaching sched-domain:
    [ 77.389945] domain 0: span 0-1 level MC
    [ 77.389952] groups: 0 1
    [ 77.389969] CPU1 attaching sched-domain:
    [ 77.390747] domain 0: span 0-1 level MC
    [ 77.390754] groups: 1 0
    [ 78.283211] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 110.283572] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 174.290184] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 302.298515] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 339.083898] eth0: Link is Down
    [ 989.922658] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [ 989.922669] eth0: 10/100 speed: disabling TSO
    [ 996.212812] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=245 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=225
    [ 996.236677] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [ 996.261093] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 996.494548] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [ 996.752414] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [ 999.273404] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 999.271538] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=366 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=346
    [ 1000.012064] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=322 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=302
    [ 1003.279285] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 1011.283681] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 1027.279340] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 1059.299283] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 1123.288205] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 1251.291253] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 1507.298085] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 2019.300268] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 3043.303167] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 5091.310288] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [ 8691.318914] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [12291.323733] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [13964.551553] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:05:c6:dd:fb:08:00 SRC=192.168.0.8 DST=224.0.0.251 LEN=409 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=389
    [14430.106248] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:05:c6:dd:fb:08:00 SRC=192.168.0.8 DST=224.0.0.251 LEN=258 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=238
    [14430.357592] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:05:c6:dd:fb:08:00 SRC=192.168.0.8 DST=224.0.0.251 LEN=258 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=238
    [14430.608855] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:05:c6:dd:fb:08:00 SRC=192.168.0.8 DST=224.0.0.251 LEN=258 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=238
    [14430.808491] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:05:c6:dd:fb:08:00 SRC=192.168.0.8 DST=224.0.0.251 LEN=240 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=220
    [14430.983512] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:05:c6:dd:fb:08:00 SRC=192.168.0.8 DST=224.0.0.251 LEN=176 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=156
    [15891.322079] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [19491.320177] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [21272.094076] uhci_hcd 0000:00:1d.0: release dev 3 ep81-INT, period 8, phase 4, 93 us
    [21272.653192] PM: Syncing filesystems ... done.
    [21272.660574] Freezing user space processes ... (elapsed 0.00 seconds) done.
    [21272.663905] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
    [21272.664041] Suspending console(s) (use no_console_suspend to debug)
    [21272.890919] usb 5-2: usb suspend
    [21273.883248] usb 2-2: usb suspend
    [21273.896815] hub 5-0:1.0: hub_suspend
    [21273.896863] usb usb5: bus suspend
    [21273.896877] usb usb5: suspend_rh
    [21273.898319] uhci_hcd 0000:00:1d.0: release dev 2 ep81-INT, period 16, phase 8, 118 us
    [21273.901318] usb 2-1: usb suspend
    [21273.916917] hub 2-0:1.0: hub_suspend
    [21273.916932] usb usb2: bus suspend
    [21273.916936] usb usb2: suspend_rh
    [21273.917177] sd 0:0:0:0: [sda] Synchronizing SCSI cache
    [21273.917540] sd 0:0:0:0: [sda] Stopping disk
    [21274.341950] e1000e 0000:02:00.0: PCI INT A disabled
    [21274.341964] ACPI handle has no context!
    [21274.389354] ehci_hcd 0000:00:1d.7: PCI INT D disabled
    [21274.407490] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D3
    [21274.407496] ehci_hcd 0000:00:1d.7: --> PCI D3
    [21274.407502] uhci_hcd 0000:00:1d.3: uhci_pci_suspend
    [21274.407601] uhci_hcd 0000:00:1d.3: PCI INT D disabled
    [21274.407603] uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    [21274.407608] uhci_hcd 0000:00:1d.2: uhci_pci_suspend
    [21274.407668] uhci_hcd 0000:00:1d.2: PCI INT C disabled
    [21274.407670] uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    [21274.407674] uhci_hcd 0000:00:1d.1: uhci_pci_suspend
    [21274.407734] uhci_hcd 0000:00:1d.1: PCI INT B disabled
    [21274.407735] uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    [21274.407740] uhci_hcd 0000:00:1d.0: uhci_pci_suspend
    [21274.407799] uhci_hcd 0000:00:1d.0: PCI INT A disabled
    [21274.407801] uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    [21274.421084] HDA Intel 0000:00:1b.0: PCI INT B disabled
    [21274.588547] ACPI: Preparing to enter system sleep state S3
    [21275.019202] Disabling non-boot CPUs ...
    [21275.021008] Broke affinity for irq 9
    [21275.021008] Broke affinity for irq 12
    [21275.021008] Broke affinity for irq 16
    [21275.021008] Broke affinity for irq 218
    [21275.120777] CPU 1 is now offline
    [21275.120780] lockdep: fixing up alternatives.
    [21275.120788] SMP alternatives: switching to UP code
    [21275.134792] CPU0 attaching NULL sched-domain.
    [21275.134872] CPU1 attaching NULL sched-domain.
    [21275.148843] CPU0 attaching NULL sched-domain.
    [21275.150036] CPU1 is down
    [21275.150193] Extended CMOS year: 2000
    [21275.150193] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [21275.151012] Back to C!
    [21275.151536] Extended CMOS year: 2000
    [21275.151871] Enabling non-boot CPUs ...
    [21275.152009] lockdep: fixing up alternatives.
    [21275.152009] SMP alternatives: switching to SMP code
    [21275.162233] Booting processor 1/1 ip 6000
    [21275.167017] Initializing CPU#1
    [21275.247022] Calibrating delay using timer specific routine.. <6>3657.63 BogoMIPS (lpj=7315267)
    [21275.247030] CPU: L1 I cache: 32K, L1 D cache: 32K
    [21275.247032] CPU: L2 cache: 2048K
    [21275.247035] CPU: Physical Processor ID: 0
    [21275.247036] CPU: Processor Core ID: 1
    [21275.247715] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
    [21275.253850] CPU1: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06
    [21275.253913] CPU0 attaching NULL sched-domain.
    [21275.252491] Switched to high resolution mode on CPU 1
    [21275.268396] CPU0 attaching sched-domain:
    [21275.268400] domain 0: span 0-1 level MC
    [21275.268402] groups: 0 1
    [21275.268410] CPU1 attaching sched-domain:
    [21275.268413] domain 0: span 0-1 level MC
    [21275.268414] groups: 1 0
    [21275.265108] CPU1 is up
    [21275.265112] ACPI: Waking up from system sleep state S3
    [21276.572739] ACPI: EC: non-query interrupt received, switching to interrupt mode
    [21276.618503] pcieport-driver 0000:00:01.0: restoring config space at offset 0x7 (was 0x20002020, writing 0x2020)
    [21276.618518] pcieport-driver 0000:00:01.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
    [21276.618568] pcieport-driver 0000:00:01.0: setting latency timer to 64
    [21276.631291] HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100106, writing 0x100102)
    [21276.631326] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [21276.631337] HDA Intel 0000:00:1b.0: setting latency timer to 64
    [21276.719219] pcieport-driver 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
    [21276.719314] pcieport-driver 0000:00:1c.0: setting latency timer to 64
    [21276.719402] pcieport-driver 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
    [21276.719492] pcieport-driver 0000:00:1c.1: setting latency timer to 64
    [21276.719565] pcieport-driver 0000:00:1c.2: restoring config space at offset 0x7 (was 0x20007060, writing 0x7060)
    [21276.719591] pcieport-driver 0000:00:1c.2: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
    [21276.719681] pcieport-driver 0000:00:1c.2: setting latency timer to 64
    [21276.719723] pcieport-driver 0000:00:1c.3: restoring config space at offset 0xf (was 0x40400, writing 0x4040b)
    [21276.719754] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x9 (was 0x10001, writing 0xe421e421)
    [21276.719762] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x8 (was 0x0, writing 0xebf0ea00)
    [21276.719775] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x7 (was 0x20000000, writing 0x9080)
    [21276.719796] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x3 (was 0x810000, writing 0x810010)
    [21276.719806] pcieport-driver 0000:00:1c.3: restoring config space at offset 0x1 (was 0x100000, writing 0x100507)
    [21276.719900] pcieport-driver 0000:00:1c.3: setting latency timer to 64
    [21276.719911] uhci_hcd 0000:00:1d.0: PCI legacy resume
    [21276.723487] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
    [21276.723495] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [21276.723502] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [21276.723551] uhci_hcd 0000:00:1d.0: uhci_pci_resume
    [21276.723558] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x2f00
    [21276.723560] uhci_hcd 0000:00:1d.0: Performing full reset
    [21276.723584] usb usb2: root hub lost power or was reset
    [21276.723587] usb usb2: suspend_rh
    [21276.723697] uhci_hcd 0000:00:1d.1: PCI legacy resume
    [21276.723706] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [21276.723713] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [21276.723761] uhci_hcd 0000:00:1d.1: uhci_pci_resume
    [21276.723766] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x2000
    [21276.723768] uhci_hcd 0000:00:1d.1: Performing full reset
    [21276.723792] usb usb3: root hub lost power or was reset
    [21276.723794] usb usb3: suspend_rh
    [21276.723812] uhci_hcd 0000:00:1d.2: PCI legacy resume
    [21276.724367] uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
    [21276.724374] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    [21276.724381] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [21276.724430] uhci_hcd 0000:00:1d.2: uhci_pci_resume
    [21276.724435] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x2000
    [21276.724437] uhci_hcd 0000:00:1d.2: Performing full reset
    [21276.724460] usb usb4: root hub lost power or was reset
    [21276.724462] usb usb4: suspend_rh
    [21276.724481] uhci_hcd 0000:00:1d.3: PCI legacy resume
    [21276.724488] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [21276.724495] uhci_hcd 0000:00:1d.3: setting latency timer to 64
    [21276.724544] uhci_hcd 0000:00:1d.3: uhci_pci_resume
    [21276.724549] uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x2000
    [21276.724551] uhci_hcd 0000:00:1d.3: Performing full reset
    [21276.724574] usb usb5: root hub lost power or was reset
    [21276.724576] usb usb5: suspend_rh
    [21276.724621] ehci_hcd 0000:00:1d.7: PCI D0, from previous PCI D3
    [21276.725242] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
    [21276.725252] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [21276.725259] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [21276.725481] pci 0000:00:1e.0: restoring config space at offset 0x1 (was 0x100005, writing 0x100007)
    [21276.725508] pci 0000:00:1e.0: setting latency timer to 64
    [21276.725639] PIIX_IDE 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
    [21276.738824] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
    [21276.738883] ahci 0000:00:1f.2: setting latency timer to 64
    [21276.739311] pci 0000:01:00.0: restoring config space at offset 0x1 (was 0x100103, writing 0x100107)
    [21276.754913] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [21276.754923] e1000e 0000:02:00.0: setting latency timer to 64
    [21276.814134] pci 0000:15:00.0: restoring config space at offset 0xf (was 0x34001ff, writing 0x3c0010b)
    [21276.814143] pci 0000:15:00.0: restoring config space at offset 0xe (was 0x0, writing 0xa4fc)
    [21276.814152] pci 0000:15:00.0: restoring config space at offset 0xd (was 0x0, writing 0xa400)
    [21276.814160] pci 0000:15:00.0: restoring config space at offset 0xc (was 0x0, writing 0xa0fc)
    [21276.814168] pci 0000:15:00.0: restoring config space at offset 0xb (was 0x0, writing 0xa000)
    [21276.814177] pci 0000:15:00.0: restoring config space at offset 0xa (was 0x0, writing 0xc7fff000)
    [21276.814185] pci 0000:15:00.0: restoring config space at offset 0x9 (was 0x0, writing 0xc4000000)
    [21276.814194] pci 0000:15:00.0: restoring config space at offset 0x8 (was 0x0, writing 0xe3fff000)
    [21276.814202] pci 0000:15:00.0: restoring config space at offset 0x7 (was 0x0, writing 0xe0000000)
    [21276.814210] pci 0000:15:00.0: restoring config space at offset 0x6 (was 0x0, writing 0xb0171615)
    [21276.814222] pci 0000:15:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xe4300000)
    [21276.814230] pci 0000:15:00.0: restoring config space at offset 0x3 (was 0x20000, writing 0x2a808)
    [21276.814242] pci 0000:15:00.0: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100007)
    [21276.814276] pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [21276.822533] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
    [21276.822826] hda: UDMA/33 mode selected
    [21276.823840] sd 0:0:0:0: [sda] Starting disk
    [21277.285295] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [21282.287089] ata1.00: qc timeout (cmd 0xec)
    [21282.287107] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    [21282.287112] ata1.00: revalidation failed (errno=-5)
    [21282.831103] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [21292.831085] ata1.00: qc timeout (cmd 0xec)
    [21292.831102] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    [21292.831106] ata1.00: revalidation failed (errno=-5)
    [21293.151157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [21323.151085] ata1.00: qc timeout (cmd 0xec)
    [21323.151101] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    [21323.151106] ata1.00: revalidation failed (errno=-5)
    [21323.151109] ata1.00: disabled
    [21323.151134] ata1: hard resetting link
    [21323.471141] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [21323.471155] ata1: EH complete
    [21323.471450] sd 0:0:0:0: [sda] START_STOP FAILED
    [21323.471454] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21323.471548] PM: Device 0:0:0:0 failed to resume: error 262144
    [21323.471629] usb usb1: usb resume
    [21323.471649] ehci_hcd 0000:00:1d.7: resume root hub
    [21323.500064] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21323.500067] end_request: I/O error, dev sda, sector 113980368
    [21323.500074] Buffer I/O error on device sda2, logical block 13861986
    [21323.500076] lost page write due to I/O error on sda2
    [21323.500168] JBD: Detected IO errors while flushing file data on sda2
    [21323.500283] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21323.500286] end_request: I/O error, dev sda, sector 3253856
    [21323.500356] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21323.500358] end_request: I/O error, dev sda, sector 3253872
    [21323.500361] Buffer I/O error on device sda2, logical block 21174
    [21323.500363] lost page write due to I/O error on sda2
    [21323.500384] Aborting journal on device sda2.
    [21323.500425] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21323.500428] end_request: I/O error, dev sda, sector 3096840
    [21323.500431] Buffer I/O error on device sda2, logical block 1545
    [21323.500433] lost page write due to I/O error on sda2
    [21323.523632] ehci_hcd 0000:00:1d.7: port 2 low speed --> companion
    [21323.523646] ehci_hcd 0000:00:1d.7: port 1 low speed --> companion
    [21323.619900] ehci_hcd 0000:00:1d.7: port 8 full speed --> companion
    [21323.619908] ehci_hcd 0000:00:1d.7: GetStatus port 8 status 003801 POWER OWNER sig=j CONNECT
    [21323.619922] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
    [21323.619936] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
    [21323.635751] hub 1-0:1.0: hub_resume
    [21323.636034] ehci_hcd 0000:00:1d.7: GetStatus port 8 status 003002 POWER OWNER sig=se0 CSC
    [21323.739909] usb usb2: usb resume
    [21323.739916] usb usb2: wakeup_rh
    [21323.776108] hub 2-0:1.0: hub_reset_resume
    [21323.776112] hub 2-0:1.0: trying to enable port power on non-switchable hub
    [21323.880113] uhci_hcd 0000:00:1d.0: port 1 portsc 01ab,00
    [21323.880129] hub 2-0:1.0: port 1: status 0301 change 0003
    [21323.880191] uhci_hcd 0000:00:1d.0: port 2 portsc 01ab,00
    [21323.880204] hub 2-0:1.0: port 2: status 0301 change 0003
    [21323.984355] usb 2-1: finish reset-resume
    [21324.243949] usb 2-1: reset low speed USB device using uhci_hcd and address 2
    [21324.553817] uhci_hcd 0000:00:1d.0: reserve dev 2 ep81-INT, period 16, phase 8, 118 us
    [21324.553851] usb usb5: usb resume
    [21324.553854] usb usb5: wakeup_rh
    [21324.592097] hub 5-0:1.0: hub_reset_resume
    [21324.592102] hub 5-0:1.0: trying to enable port power on non-switchable hub
    [21324.696106] uhci_hcd 0000:00:1d.3: port 2 portsc 009b,00
    [21324.696120] hub 5-0:1.0: port 2: status 0101 change 0003
    [21324.800065] usb 2-2: finish reset-resume
    [21325.059903] usb 2-2: reset low speed USB device using uhci_hcd and address 3
    [21325.372156] usb 5-2: finish reset-resume
    [21325.483632] usb 5-2: reset full speed USB device using uhci_hcd and address 2
    [21325.615567] usb 5-2: ep0 maxpacket = 8
    [21325.644009] Restarting tasks ... <2>ext3_abort called.
    [21325.646508] EXT3-fs error (device sda2): ext3_journal_start_sb: Detected aborted journal
    [21325.646519] Remounting filesystem read-only
    [21325.673275] done.
    [21325.689647] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21325.689652] end_request: I/O error, dev sda, sector 119819760
    [21325.689971] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
    [21325.689985] hub 2-0:1.0: state 7 ports 2 chg 0006 evt 0000
    [21325.690015] hub 2-0:1.0: port 1, status 0303, change 0000, 1.5 Mb/s
    [21325.690032] hub 2-0:1.0: port 2, status 0303, change 0000, 1.5 Mb/s
    [21325.690038] hub 5-0:1.0: state 7 ports 2 chg 0004 evt 0000
    [21325.690056] hub 5-0:1.0: port 2, status 0103, change 0000, 12 Mb/s
    [21325.690216] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21325.690220] end_request: I/O error, dev sda, sector 119819760
    [21325.691980] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21325.691984] end_request: I/O error, dev sda, sector 119819936
    [21325.692109] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21325.692112] end_request: I/O error, dev sda, sector 119819936
    [21326.363187] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 93 us
    [21326.396473] uhci_hcd 0000:00:1d.0: release dev 3 ep81-INT, period 8, phase 4, 93 us
    [21326.424986] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21326.424997] end_request: I/O error, dev sda, sector 107727184
    [21326.426037] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21326.426046] end_request: I/O error, dev sda, sector 107727184
    [21326.427164] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21326.427174] end_request: I/O error, dev sda, sector 107727184
    [21326.593037] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 93 us
    [21327.820633] hub 1-0:1.0: hub_suspend
    [21327.823044] usb usb1: bus auto-suspend
    [21327.823066] ehci_hcd 0000:00:1d.7: suspend root hub
    [21328.188056] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [21328.188056] eth0: 10/100 speed: disabling TSO
    [21330.680181] SFW2-OUT-ERROR IN= OUT=tun0 SRC=10.20.10.56 DST=10.20.0.6 LEN=89 TOS=0x00 PREC=0x00 TTL=64 ID=42862 DF PROTO=TCP SPT=10147 DPT=993 WINDOW=972 RES=0x00 ACK PSH FIN URGP=0 OPT (0101080A005039C47A78A702)
    [21336.164109] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [21336.370286] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [21336.443679] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=245 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=225
    [21336.628056] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [21336.884053] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=352 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=332
    [21337.072054] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21337.072054] end_request: I/O error, dev sda, sector 64548368
    [21337.072054] EXT3-fs error (device sda2): ext3_find_entry: reading directory #3834545 offset 0
    [21355.725332] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21355.725360] end_request: I/O error, dev sda, sector 112136592
    [21355.725378] Buffer I/O error on device sda2, logical block 13631514
    [21355.725388] lost page write due to I/O error on sda2
    [21363.466428] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.466438] end_request: I/O error, dev sda, sector 87357760
    [21363.466465] EXT3-fs error (device sda2): ext3_find_entry: reading directory #5259374 offset 0
    [21363.486583] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.486592] end_request: I/O error, dev sda, sector 76136968
    [21363.487434] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.487442] end_request: I/O error, dev sda, sector 76136976
    [21363.488340] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.488348] end_request: I/O error, dev sda, sector 76136984
    [21363.489071] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.489079] end_request: I/O error, dev sda, sector 76136992
    [21363.489824] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.489832] end_request: I/O error, dev sda, sector 76137000
    [21363.490764] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.490773] end_request: I/O error, dev sda, sector 76137008
    [21363.491558] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.491566] end_request: I/O error, dev sda, sector 76137016
    [21363.492318] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.492326] end_request: I/O error, dev sda, sector 76137024
    [21363.493249] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.493258] end_request: I/O error, dev sda, sector 76137032
    [21363.494034] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.494044] end_request: I/O error, dev sda, sector 76137040
    [21363.494716] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.494724] end_request: I/O error, dev sda, sector 76137048
    [21363.495346] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.495354] end_request: I/O error, dev sda, sector 76137056
    [21363.496014] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.496021] end_request: I/O error, dev sda, sector 76137064
    [21363.496647] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.496655] end_request: I/O error, dev sda, sector 76137064
    [21363.497305] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.497312] end_request: I/O error, dev sda, sector 76137064
    [21363.497932] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.497939] end_request: I/O error, dev sda, sector 76137064
    [21363.498556] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.498563] end_request: I/O error, dev sda, sector 76137064
    [21363.499200] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.499207] end_request: I/O error, dev sda, sector 76137064
    [21363.499841] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.499848] end_request: I/O error, dev sda, sector 76137064
    [21363.500502] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.500509] end_request: I/O error, dev sda, sector 76137064
    [21363.501152] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.501159] end_request: I/O error, dev sda, sector 76137064
    [21363.501780] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.501787] end_request: I/O error, dev sda, sector 76137064
    [21363.502404] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.502411] end_request: I/O error, dev sda, sector 76137064
    [21363.503028] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.503035] end_request: I/O error, dev sda, sector 76137064
    [21363.503652] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.503659] end_request: I/O error, dev sda, sector 76137064
    [21363.504831] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.504840] end_request: I/O error, dev sda, sector 76137064
    [21363.505572] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.505579] end_request: I/O error, dev sda, sector 76137064
    [21363.506204] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.506211] end_request: I/O error, dev sda, sector 76137064
    [21363.506830] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.506837] end_request: I/O error, dev sda, sector 76137064
    [21363.507460] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.507467] end_request: I/O error, dev sda, sector 76137064
    [21363.508102] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.508110] end_request: I/O error, dev sda, sector 76137064
    [21363.508729] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.508737] end_request: I/O error, dev sda, sector 76137064
    [21363.509378] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.509385] end_request: I/O error, dev sda, sector 76137064
    [21363.509999] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.510006] end_request: I/O error, dev sda, sector 76137064
    [21363.510621] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.510628] end_request: I/O error, dev sda, sector 76137064
    [21363.511258] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.511265] end_request: I/O error, dev sda, sector 76137064
    [21363.511900] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.511907] end_request: I/O error, dev sda, sector 76137064
    [21363.512527] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.512534] end_request: I/O error, dev sda, sector 76137064
    [21363.513167] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.513174] end_request: I/O error, dev sda, sector 76137064
    [21363.513791] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.513798] end_request: I/O error, dev sda, sector 76137064
    [21363.514420] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.514427] end_request: I/O error, dev sda, sector 76137064
    [21363.515046] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.515053] end_request: I/O error, dev sda, sector 76137064
    [21363.515671] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.515679] end_request: I/O error, dev sda, sector 76137064
    [21363.516328] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.516335] end_request: I/O error, dev sda, sector 76137064
    [21363.516979] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.516986] end_request: I/O error, dev sda, sector 76137064
    [21363.517606] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.517613] end_request: I/O error, dev sda, sector 76137064
    [21363.518231] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.518238] end_request: I/O error, dev sda, sector 76137064
    [21363.518849] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.518856] end_request: I/O error, dev sda, sector 76137064
    [21363.519455] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.519462] end_request: I/O error, dev sda, sector 76137064
    [21363.520155] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.520162] end_request: I/O error, dev sda, sector 76137064
    [21363.520741] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.520748] end_request: I/O error, dev sda, sector 76137064
    [21363.521613] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.521621] end_request: I/O error, dev sda, sector 76137064
    [21363.522292] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21363.522299] end_request: I/O error, dev sda, sector 76136968
    [21367.196056] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [21399.199282] SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.9 DST=224.0.0.251 LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
    [21414.252018] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21414.252018] end_request: I/O error, dev sda, sector 110674896
    [21414.252018] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21414.252018] end_request: I/O error, dev sda, sector 110674896
    [21414.287205] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21414.287220] end_request: I/O error, dev sda, sector 112311768
    [21414.287268] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21414.287279] end_request: I/O error, dev sda, sector 112314904
    [21414.287362] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21414.287372] end_request: I/O error, dev sda, sector 112311768
    [21414.288444] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21414.288450] end_request: I/O error, dev sda, sector 112311768
    [21421.112015] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21421.112015] end_request: I/O error, dev sda, sector 107712840
    [21421.112015] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21421.112015] end_request: I/O error, dev sda, sector 107712840
    [21421.112015] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    [21421.112015] end_request: I/O error, dev sda, sector 107712840



    #
    # Automatically generated make config: don't edit
    # Linux kernel version: 2.6.27-rc1
    # Tue Jul 29 16:18:05 2008
    #
    CONFIG_64BIT=y
    # CONFIG_X86_32 is not set
    CONFIG_X86_64=y
    CONFIG_X86=y
    CONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig"
    # CONFIG_GENERIC_LOCKBREAK is not set
    CONFIG_GENERIC_TIME=y
    CONFIG_GENERIC_CMOS_UPDATE=y
    CONFIG_CLOCKSOURCE_WATCHDOG=y
    CONFIG_GENERIC_CLOCKEVENTS=y
    CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
    CONFIG_LOCKDEP_SUPPORT=y
    CONFIG_STACKTRACE_SUPPORT=y
    CONFIG_HAVE_LATENCYTOP_SUPPORT=y
    CONFIG_FAST_CMPXCHG_LOCAL=y
    CONFIG_MMU=y
    CONFIG_ZONE_DMA=y
    CONFIG_GENERIC_ISA_DMA=y
    CONFIG_GENERIC_IOMAP=y
    CONFIG_GENERIC_BUG=y
    CONFIG_GENERIC_HWEIGHT=y
    # CONFIG_GENERIC_GPIO is not set
    CONFIG_ARCH_MAY_HAVE_PC_FDC=y
    CONFIG_RWSEM_GENERIC_SPINLOCK=y
    # CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
    # CONFIG_ARCH_HAS_ILOG2_U32 is not set
    # CONFIG_ARCH_HAS_ILOG2_U64 is not set
    CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
    CONFIG_GENERIC_CALIBRATE_DELAY=y
    CONFIG_GENERIC_TIME_VSYSCALL=y
    CONFIG_ARCH_HAS_CPU_RELAX=y
    CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
    CONFIG_HAVE_SETUP_PER_CPU_AREA=y
    CONFIG_HAVE_CPUMASK_OF_CPU_MAP=y
    CONFIG_ARCH_HIBERNATION_POSSIBLE=y
    CONFIG_ARCH_SUSPEND_POSSIBLE=y
    CONFIG_ZONE_DMA32=y
    CONFIG_ARCH_POPULATES_NODE_MAP=y
    CONFIG_AUDIT_ARCH=y
    CONFIG_ARCH_SUPPORTS_AOUT=y
    CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
    CONFIG_GENERIC_HARDIRQS=y
    CONFIG_GENERIC_IRQ_PROBE=y
    CONFIG_GENERIC_PENDING_IRQ=y
    CONFIG_X86_SMP=y
    CONFIG_X86_64_SMP=y
    CONFIG_X86_HT=y
    CONFIG_X86_BIOS_REBOOT=y
    CONFIG_X86_TRAMPOLINE=y
    # CONFIG_KTIME_SCALAR is not set
    CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

    #
    # General setup
    #
    CONFIG_EXPERIMENTAL=y
    CONFIG_LOCK_KERNEL=y
    CONFIG_INIT_ENV_ARG_LIMIT=32
    CONFIG_LOCALVERSION=""
    CONFIG_LOCALVERSION_AUTO=y
    CONFIG_SWAP=y
    CONFIG_SYSVIPC=y
    CONFIG_SYSVIPC_SYSCTL=y
    CONFIG_POSIX_MQUEUE=y
    # CONFIG_BSD_PROCESS_ACCT is not set
    # CONFIG_TASKSTATS is not set
    # CONFIG_AUDIT is not set
    # CONFIG_IKCONFIG is not set
    CONFIG_LOG_BUF_SHIFT=20
    # CONFIG_CGROUPS is not set
    CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
    # CONFIG_GROUP_SCHED is not set
    CONFIG_SYSFS_DEPRECATED=y
    CONFIG_SYSFS_DEPRECATED_V2=y
    # CONFIG_RELAY is not set
    CONFIG_NAMESPACES=y
    # CONFIG_UTS_NS is not set
    # CONFIG_IPC_NS is not set
    # CONFIG_USER_NS is not set
    # CONFIG_PID_NS is not set
    # CONFIG_BLK_DEV_INITRD is not set
    CONFIG_CC_OPTIMIZE_FOR_SIZE=y
    CONFIG_SYSCTL=y
    # CONFIG_EMBEDDED is not set
    CONFIG_UID16=y
    CONFIG_SYSCTL_SYSCALL=y
    CONFIG_SYSCTL_SYSCALL_CHECK=y
    CONFIG_KALLSYMS=y
    CONFIG_KALLSYMS_ALL=y
    # CONFIG_KALLSYMS_EXTRA_PASS is not set
    CONFIG_HOTPLUG=y
    CONFIG_PRINTK=y
    CONFIG_BUG=y
    CONFIG_ELF_CORE=y
    CONFIG_PCSPKR_PLATFORM=y
    # CONFIG_COMPAT_BRK is not set
    CONFIG_BASE_FULL=y
    CONFIG_FUTEX=y
    CONFIG_ANON_INODES=y
    CONFIG_EPOLL=y
    CONFIG_SIGNALFD=y
    CONFIG_TIMERFD=y
    CONFIG_EVENTFD=y
    CONFIG_SHMEM=y
    CONFIG_VM_EVENT_COUNTERS=y
    CONFIG_SLAB=y
    # CONFIG_SLUB is not set
    # CONFIG_SLOB is not set
    # CONFIG_PROFILING is not set
    # CONFIG_MARKERS is not set
    CONFIG_HAVE_OPROFILE=y
    # CONFIG_KPROBES is not set
    CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
    CONFIG_HAVE_IOREMAP_PROT=y
    CONFIG_HAVE_KPROBES=y
    CONFIG_HAVE_KRETPROBES=y
    # CONFIG_HAVE_ARCH_TRACEHOOK is not set
    # CONFIG_HAVE_DMA_ATTRS is not set
    CONFIG_USE_GENERIC_SMP_HELPERS=y
    # CONFIG_HAVE_CLK is not set
    CONFIG_PROC_PAGE_MONITOR=y
    # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
    CONFIG_SLABINFO=y
    CONFIG_RT_MUTEXES=y
    # CONFIG_TINY_SHMEM is not set
    CONFIG_BASE_SMALL=0
    CONFIG_MODULES=y
    # CONFIG_MODULE_FORCE_LOAD is not set
    CONFIG_MODULE_UNLOAD=y
    CONFIG_MODULE_FORCE_UNLOAD=y
    # CONFIG_MODVERSIONS is not set
    # CONFIG_MODULE_SRCVERSION_ALL is not set
    CONFIG_KMOD=y
    CONFIG_STOP_MACHINE=y
    CONFIG_BLOCK=y
    # CONFIG_BLK_DEV_IO_TRACE is not set
    # CONFIG_BLK_DEV_BSG is not set
    # CONFIG_BLK_DEV_INTEGRITY is not set
    CONFIG_BLOCK_COMPAT=y

    #
    # IO Schedulers
    #
    CONFIG_IOSCHED_NOOP=y
    # CONFIG_IOSCHED_AS is not set
    # CONFIG_IOSCHED_DEADLINE is not set
    CONFIG_IOSCHED_CFQ=y
    # CONFIG_DEFAULT_AS is not set
    # CONFIG_DEFAULT_DEADLINE is not set
    CONFIG_DEFAULT_CFQ=y
    # CONFIG_DEFAULT_NOOP is not set
    CONFIG_DEFAULT_IOSCHED="cfq"
    CONFIG_PREEMPT_NOTIFIERS=y
    CONFIG_CLASSIC_RCU=y

    #
    # Processor type and features
    #
    CONFIG_TICK_ONESHOT=y
    CONFIG_NO_HZ=y
    CONFIG_HIGH_RES_TIMERS=y
    CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
    CONFIG_SMP=y
    CONFIG_X86_FIND_SMP_CONFIG=y
    CONFIG_X86_MPPARSE=y
    CONFIG_X86_PC=y
    # CONFIG_X86_ELAN is not set
    # CONFIG_X86_VOYAGER is not set
    # CONFIG_X86_GENERICARCH is not set
    # CONFIG_X86_VSMP is not set
    # CONFIG_PARAVIRT_GUEST is not set
    # CONFIG_MEMTEST is not set
    # CONFIG_M386 is not set
    # CONFIG_M486 is not set
    # CONFIG_M586 is not set
    # CONFIG_M586TSC is not set
    # CONFIG_M586MMX is not set
    # CONFIG_M686 is not set
    # CONFIG_MPENTIUMII is not set
    # CONFIG_MPENTIUMIII is not set
    # CONFIG_MPENTIUMM is not set
    # CONFIG_MPENTIUM4 is not set
    # CONFIG_MK6 is not set
    # CONFIG_MK7 is not set
    # CONFIG_MK8 is not set
    # CONFIG_MCRUSOE is not set
    # CONFIG_MEFFICEON is not set
    # CONFIG_MWINCHIPC6 is not set
    # CONFIG_MWINCHIP2 is not set
    # CONFIG_MWINCHIP3D is not set
    # CONFIG_MGEODEGX1 is not set
    # CONFIG_MGEODE_LX is not set
    # CONFIG_MCYRIXIII is not set
    # CONFIG_MVIAC3_2 is not set
    # CONFIG_MVIAC7 is not set
    # CONFIG_MPSC is not set
    CONFIG_MCORE2=y
    # CONFIG_GENERIC_CPU is not set
    CONFIG_X86_CPU=y
    CONFIG_X86_L1_CACHE_BYTES=64
    CONFIG_X86_INTERNODE_CACHE_BYTES=64
    CONFIG_X86_CMPXCHG=y
    CONFIG_X86_L1_CACHE_SHIFT=6
    CONFIG_X86_WP_WORKS_OK=y
    CONFIG_X86_INTEL_USERCOPY=y
    CONFIG_X86_USE_PPRO_CHECKSUM=y
    CONFIG_X86_P6_NOP=y
    CONFIG_X86_TSC=y
    CONFIG_X86_CMPXCHG64=y
    CONFIG_X86_CMOV=y
    CONFIG_X86_MINIMUM_CPU_FAMILY=64
    CONFIG_X86_DEBUGCTLMSR=y
    CONFIG_HPET_TIMER=y
    CONFIG_HPET_EMULATE_RTC=y
    CONFIG_DMI=y
    CONFIG_GART_IOMMU=y
    # CONFIG_CALGARY_IOMMU is not set
    # CONFIG_AMD_IOMMU is not set
    CONFIG_SWIOTLB=y
    CONFIG_IOMMU_HELPER=y
    # CONFIG_MAXSMP is not set
    CONFIG_NR_CPUS=2
    # CONFIG_SCHED_SMT is not set
    CONFIG_SCHED_MC=y
    # CONFIG_PREEMPT_NONE is not set
    CONFIG_PREEMPT_VOLUNTARY=y
    # CONFIG_PREEMPT is not set
    CONFIG_X86_LOCAL_APIC=y
    CONFIG_X86_IO_APIC=y
    CONFIG_X86_MCE=y
    CONFIG_X86_MCE_INTEL=y
    # CONFIG_X86_MCE_AMD is not set
    # CONFIG_I8K is not set
    CONFIG_MICROCODE=m
    CONFIG_MICROCODE_OLD_INTERFACE=y
    CONFIG_X86_MSR=m
    CONFIG_X86_CPUID=m
    # CONFIG_NUMA is not set
    CONFIG_ARCH_SPARSEMEM_DEFAULT=y
    CONFIG_ARCH_SPARSEMEM_ENABLE=y
    CONFIG_ARCH_SELECT_MEMORY_MODEL=y
    CONFIG_SELECT_MEMORY_MODEL=y
    # CONFIG_FLATMEM_MANUAL is not set
    # CONFIG_DISCONTIGMEM_MANUAL is not set
    CONFIG_SPARSEMEM_MANUAL=y
    CONFIG_SPARSEMEM=y
    CONFIG_HAVE_GET_USER_PAGES_FAST=y
    CONFIG_HAVE_MEMORY_PRESENT=y
    # CONFIG_SPARSEMEM_STATIC is not set
    CONFIG_SPARSEMEM_EXTREME=y
    CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
    # CONFIG_SPARSEMEM_VMEMMAP is not set
    # CONFIG_MEMORY_HOTPLUG is not set
    CONFIG_PAGEFLAGS_EXTENDED=y
    CONFIG_SPLIT_PTLOCK_CPUS=4
    CONFIG_RESOURCES_64BIT=y
    CONFIG_ZONE_DMA_FLAG=1
    CONFIG_BOUNCE=y
    CONFIG_VIRT_TO_BUS=y
    CONFIG_MMU_NOTIFIER=y
    CONFIG_MTRR=y
    # CONFIG_MTRR_SANITIZER is not set
    CONFIG_X86_PAT=y
    # CONFIG_EFI is not set
    # CONFIG_SECCOMP is not set
    # CONFIG_HZ_100 is not set
    CONFIG_HZ_250=y
    # CONFIG_HZ_300 is not set
    # CONFIG_HZ_1000 is not set
    CONFIG_HZ=250
    CONFIG_SCHED_HRTICK=y
    # CONFIG_KEXEC is not set
    # CONFIG_CRASH_DUMP is not set
    CONFIG_PHYSICAL_START=0x200000
    # CONFIG_RELOCATABLE is not set
    CONFIG_PHYSICAL_ALIGN=0x200000
    CONFIG_HOTPLUG_CPU=y
    CONFIG_COMPAT_VDSO=y
    CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

    #
    # Power management options
    #
    CONFIG_PM=y
    # CONFIG_PM_DEBUG is not set
    CONFIG_PM_SLEEP_SMP=y
    CONFIG_PM_SLEEP=y
    CONFIG_SUSPEND=y
    CONFIG_SUSPEND_FREEZER=y
    # CONFIG_HIBERNATION is not set
    CONFIG_ACPI=y
    CONFIG_ACPI_SLEEP=y
    CONFIG_ACPI_PROCFS=y
    CONFIG_ACPI_PROCFS_POWER=y
    CONFIG_ACPI_SYSFS_POWER=y
    CONFIG_ACPI_PROC_EVENT=y
    CONFIG_ACPI_AC=m
    CONFIG_ACPI_BATTERY=m
    CONFIG_ACPI_BUTTON=m
    CONFIG_ACPI_FAN=m
    CONFIG_ACPI_DOCK=y
    # CONFIG_ACPI_BAY is not set
    CONFIG_ACPI_PROCESSOR=m
    CONFIG_ACPI_HOTPLUG_CPU=y
    CONFIG_ACPI_THERMAL=m
    # CONFIG_ACPI_WMI is not set
    # CONFIG_ACPI_ASUS is not set
    # CONFIG_ACPI_TOSHIBA is not set
    # CONFIG_ACPI_CUSTOM_DSDT is not set
    CONFIG_ACPI_BLACKLIST_YEAR=0
    # CONFIG_ACPI_DEBUG is not set
    CONFIG_ACPI_EC=y
    # CONFIG_ACPI_PCI_SLOT is not set
    CONFIG_ACPI_POWER=y
    CONFIG_ACPI_SYSTEM=y
    CONFIG_X86_PM_TIMER=y
    CONFIG_ACPI_CONTAINER=m
    # CONFIG_ACPI_SBS is not set

    #
    # CPU Frequency scaling
    #
    CONFIG_CPU_FREQ=y
    CONFIG_CPU_FREQ_TABLE=y
    # CONFIG_CPU_FREQ_DEBUG is not set
    CONFIG_CPU_FREQ_STAT=y
    # CONFIG_CPU_FREQ_STAT_DETAILS is not set
    CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
    # CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
    # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
    # CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
    # CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
    CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
    CONFIG_CPU_FREQ_GOV_POWERSAVE=y
    CONFIG_CPU_FREQ_GOV_USERSPACE=y
    CONFIG_CPU_FREQ_GOV_ONDEMAND=y
    CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y

    #
    # CPUFreq processor drivers
    #
    CONFIG_X86_ACPI_CPUFREQ=m
    # CONFIG_X86_POWERNOW_K8 is not set
    # CONFIG_X86_SPEEDSTEP_CENTRINO is not set
    # CONFIG_X86_P4_CLOCKMOD is not set

    #
    # shared options
    #
    # CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
    # CONFIG_X86_SPEEDSTEP_LIB is not set
    # CONFIG_CPU_IDLE is not set

    #
    # Bus options (PCI etc.)
    #
    CONFIG_PCI=y
    CONFIG_PCI_DIRECT=y
    # CONFIG_PCI_MMCONFIG is not set
    CONFIG_PCI_DOMAINS=y
    # CONFIG_DMAR is not set
    CONFIG_PCIEPORTBUS=y
    CONFIG_PCIEAER=y
    # CONFIG_PCIEASPM is not set
    CONFIG_ARCH_SUPPORTS_MSI=y
    CONFIG_PCI_MSI=y
    CONFIG_PCI_LEGACY=y
    # CONFIG_PCI_DEBUG is not set
    # CONFIG_HT_IRQ is not set
    CONFIG_ISA_DMA_API=y
    CONFIG_K8_NB=y
    # CONFIG_PCCARD is not set
    # CONFIG_HOTPLUG_PCI is not set

    #
    # Executable file formats / Emulations
    #
    CONFIG_BINFMT_ELF=y
    CONFIG_COMPAT_BINFMT_ELF=y
    # CONFIG_BINFMT_MISC is not set
    CONFIG_IA32_EMULATION=y
    # CONFIG_IA32_AOUT is not set
    CONFIG_COMPAT=y
    CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
    CONFIG_SYSVIPC_COMPAT=y

    #
    # Networking
    #
    CONFIG_NET=y

    #
    # Networking options
    #
    CONFIG_PACKET=y
    # CONFIG_PACKET_MMAP is not set
    CONFIG_UNIX=y
    # CONFIG_NET_KEY is not set
    CONFIG_INET=y
    # CONFIG_IP_MULTICAST is not set
    # CONFIG_IP_ADVANCED_ROUTER is not set
    CONFIG_IP_FIB_HASH=y
    # CONFIG_IP_PNP is not set
    # CONFIG_NET_IPIP is not set
    # CONFIG_NET_IPGRE is not set
    # CONFIG_ARPD is not set
    # CONFIG_SYN_COOKIES is not set
    # CONFIG_INET_AH is not set
    # CONFIG_INET_ESP is not set
    # CONFIG_INET_IPCOMP is not set
    # CONFIG_INET_XFRM_TUNNEL is not set
    # CONFIG_INET_TUNNEL is not set
    # CONFIG_INET_XFRM_MODE_TRANSPORT is not set
    # CONFIG_INET_XFRM_MODE_TUNNEL is not set
    # CONFIG_INET_XFRM_MODE_BEET is not set
    # CONFIG_INET_LRO is not set
    # CONFIG_INET_DIAG is not set
    # CONFIG_TCP_CONG_ADVANCED is not set
    CONFIG_TCP_CONG_CUBIC=y
    CONFIG_DEFAULT_TCP_CONG="cubic"
    # CONFIG_TCP_MD5SIG is not set
    # CONFIG_IP_VS is not set
    # CONFIG_IPV6 is not set
    # CONFIG_NETWORK_SECMARK is not set
    CONFIG_NETFILTER=y
    # CONFIG_NETFILTER_DEBUG is not set
    CONFIG_NETFILTER_ADVANCED=y

    #
    # Core Netfilter Configuration
    #
    # CONFIG_NETFILTER_NETLINK_QUEUE is not set
    # CONFIG_NETFILTER_NETLINK_LOG is not set
    CONFIG_NF_CONNTRACK=y
    # CONFIG_NF_CT_ACCT is not set
    # CONFIG_NF_CONNTRACK_MARK is not set
    # CONFIG_NF_CONNTRACK_EVENTS is not set
    # CONFIG_NF_CT_PROTO_DCCP is not set
    # CONFIG_NF_CT_PROTO_SCTP is not set
    # CONFIG_NF_CT_PROTO_UDPLITE is not set
    # CONFIG_NF_CONNTRACK_AMANDA is not set
    # CONFIG_NF_CONNTRACK_FTP is not set
    # CONFIG_NF_CONNTRACK_H323 is not set
    # CONFIG_NF_CONNTRACK_IRC is not set
    # CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
    # CONFIG_NF_CONNTRACK_PPTP is not set
    # CONFIG_NF_CONNTRACK_SANE is not set
    # CONFIG_NF_CONNTRACK_SIP is not set
    # CONFIG_NF_CONNTRACK_TFTP is not set
    # CONFIG_NF_CT_NETLINK is not set
    CONFIG_NETFILTER_XTABLES=y
    # CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
    # CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
    # CONFIG_NETFILTER_XT_TARGET_DSCP is not set
    # CONFIG_NETFILTER_XT_TARGET_MARK is not set
    # CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
    # CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
    # CONFIG_NETFILTER_XT_TARGET_RATEEST is not set
    # CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
    # CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
    # CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
    # CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
    # CONFIG_NETFILTER_XT_MATCH_CONNLIMIT is not set
    # CONFIG_NETFILTER_XT_MATCH_CONNMARK is not set
    # CONFIG_NETFILTER_XT_MATCH_CONNTRACK is not set
    # CONFIG_NETFILTER_XT_MATCH_DCCP is not set
    # CONFIG_NETFILTER_XT_MATCH_DSCP is not set
    # CONFIG_NETFILTER_XT_MATCH_ESP is not set
    # CONFIG_NETFILTER_XT_MATCH_HELPER is not set
    # CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set
    # CONFIG_NETFILTER_XT_MATCH_LENGTH is not set
    CONFIG_NETFILTER_XT_MATCH_LIMIT=y
    # CONFIG_NETFILTER_XT_MATCH_MAC is not set
    # CONFIG_NETFILTER_XT_MATCH_MARK is not set
    # CONFIG_NETFILTER_XT_MATCH_OWNER is not set
    CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y
    CONFIG_NETFILTER_XT_MATCH_PKTTYPE=y
    # CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
    # CONFIG_NETFILTER_XT_MATCH_RATEEST is not set
    # CONFIG_NETFILTER_XT_MATCH_REALM is not set
    # CONFIG_NETFILTER_XT_MATCH_SCTP is not set
    CONFIG_NETFILTER_XT_MATCH_STATE=y
    # CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
    # CONFIG_NETFILTER_XT_MATCH_STRING is not set
    # CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set
    # CONFIG_NETFILTER_XT_MATCH_TIME is not set
    # CONFIG_NETFILTER_XT_MATCH_U32 is not set
    # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set

    #
    # IP: Netfilter Configuration
    #
    CONFIG_NF_CONNTRACK_IPV4=y
    # CONFIG_NF_CONNTRACK_PROC_COMPAT is not set
    # CONFIG_IP_NF_QUEUE is not set
    CONFIG_IP_NF_IPTABLES=y
    # CONFIG_IP_NF_MATCH_RECENT is not set
    # CONFIG_IP_NF_MATCH_ECN is not set
    # CONFIG_IP_NF_MATCH_AH is not set
    # CONFIG_IP_NF_MATCH_TTL is not set
    # CONFIG_IP_NF_MATCH_ADDRTYPE is not set
    CONFIG_IP_NF_FILTER=y
    CONFIG_IP_NF_TARGET_REJECT=y
    CONFIG_IP_NF_TARGET_LOG=y
    # CONFIG_IP_NF_TARGET_ULOG is not set
    CONFIG_NF_NAT=y
    CONFIG_NF_NAT_NEEDED=y
    CONFIG_IP_NF_TARGET_MASQUERADE=m
    # CONFIG_IP_NF_TARGET_REDIRECT is not set
    # CONFIG_IP_NF_TARGET_NETMAP is not set
    # CONFIG_NF_NAT_SNMP_BASIC is not set
    # CONFIG_NF_NAT_FTP is not set
    # CONFIG_NF_NAT_IRC is not set
    # CONFIG_NF_NAT_TFTP is not set
    # CONFIG_NF_NAT_AMANDA is not set
    # CONFIG_NF_NAT_PPTP is not set
    # CONFIG_NF_NAT_H323 is not set
    # CONFIG_NF_NAT_SIP is not set
    CONFIG_IP_NF_MANGLE=y
    # CONFIG_IP_NF_TARGET_ECN is not set
    # CONFIG_IP_NF_TARGET_TTL is not set
    # CONFIG_IP_NF_TARGET_CLUSTERIP is not set
    # CONFIG_IP_NF_RAW is not set
    # CONFIG_IP_NF_ARPTABLES is not set
    # CONFIG_IP_DCCP is not set
    # CONFIG_IP_SCTP is not set
    # CONFIG_TIPC is not set
    # CONFIG_ATM is not set
    # CONFIG_BRIDGE is not set
    # CONFIG_VLAN_8021Q is not set
    # CONFIG_DECNET is not set
    # CONFIG_LLC2 is not set
    # CONFIG_IPX is not set
    # CONFIG_ATALK is not set
    # CONFIG_X25 is not set
    # CONFIG_LAPB is not set
    # CONFIG_ECONET is not set
    # CONFIG_WAN_ROUTER is not set
    # CONFIG_NET_SCHED is not set

    #
    # Network testing
    #
    # CONFIG_NET_PKTGEN is not set
    # CONFIG_HAMRADIO is not set
    # CONFIG_CAN is not set
    # CONFIG_IRDA is not set
    # CONFIG_BT is not set
    # CONFIG_AF_RXRPC is not set

    #
    # Wireless
    #
    CONFIG_CFG80211=m
    CONFIG_NL80211=y
    CONFIG_WIRELESS_EXT=y
    CONFIG_WIRELESS_EXT_SYSFS=y
    CONFIG_MAC80211=m

    #
    # Rate control algorithm selection
    #
    CONFIG_MAC80211_RC_PID=y
    CONFIG_MAC80211_RC_DEFAULT_PID=y
    CONFIG_MAC80211_RC_DEFAULT="pid"
    # CONFIG_MAC80211_MESH is not set
    CONFIG_MAC80211_LEDS=y
    # CONFIG_MAC80211_DEBUGFS is not set
    # CONFIG_MAC80211_DEBUG_MENU is not set
    CONFIG_IEEE80211=m
    # CONFIG_IEEE80211_DEBUG is not set
    CONFIG_IEEE80211_CRYPT_WEP=m
    CONFIG_IEEE80211_CRYPT_CCMP=m
    CONFIG_IEEE80211_CRYPT_TKIP=m
    CONFIG_RFKILL=m
    CONFIG_RFKILL_INPUT=m
    CONFIG_RFKILL_LEDS=y
    # CONFIG_NET_9P is not set

    #
    # Device Drivers
    #

    #
    # Generic Driver Options
    #
    CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
    CONFIG_STANDALONE=y
    CONFIG_PREVENT_FIRMWARE_BUILD=y
    CONFIG_FW_LOADER=y
    CONFIG_FIRMWARE_IN_KERNEL=y
    CONFIG_EXTRA_FIRMWARE=""
    # CONFIG_DEBUG_DRIVER is not set
    # CONFIG_DEBUG_DEVRES is not set
    # CONFIG_SYS_HYPERVISOR is not set
    # CONFIG_CONNECTOR is not set
    # CONFIG_MTD is not set
    # CONFIG_PARPORT is not set
    CONFIG_PNP=y
    # CONFIG_PNP_DEBUG is not set

    #
    # Protocols
    #
    CONFIG_PNPACPI=y
    CONFIG_BLK_DEV=y
    # CONFIG_BLK_DEV_FD is not set
    # CONFIG_BLK_CPQ_DA is not set
    # CONFIG_BLK_CPQ_CISS_DA is not set
    # CONFIG_BLK_DEV_DAC960 is not set
    # CONFIG_BLK_DEV_UMEM is not set
    # CONFIG_BLK_DEV_COW_COMMON is not set
    CONFIG_BLK_DEV_LOOP=y
    # CONFIG_BLK_DEV_CRYPTOLOOP is not set
    # CONFIG_BLK_DEV_NBD is not set
    # CONFIG_BLK_DEV_SX8 is not set
    # CONFIG_BLK_DEV_UB is not set
    # CONFIG_BLK_DEV_RAM is not set
    # CONFIG_CDROM_PKTCDVD is not set
    # CONFIG_ATA_OVER_ETH is not set
    # CONFIG_BLK_DEV_HD is not set
    CONFIG_MISC_DEVICES=y
    # CONFIG_IBM_ASM is not set
    # CONFIG_PHANTOM is not set
    # CONFIG_EEPROM_93CX6 is not set
    # CONFIG_SGI_IOC4 is not set
    # CONFIG_TIFM_CORE is not set
    # CONFIG_ACER_WMI is not set
    # CONFIG_ASUS_LAPTOP is not set
    # CONFIG_FUJITSU_LAPTOP is not set
    # CONFIG_MSI_LAPTOP is not set
    # CONFIG_COMPAL_LAPTOP is not set
    # CONFIG_SONY_LAPTOP is not set
    CONFIG_THINKPAD_ACPI=m
    # CONFIG_THINKPAD_ACPI_DEBUG is not set
    CONFIG_THINKPAD_ACPI_BAY=y
    CONFIG_THINKPAD_ACPI_VIDEO=y
    CONFIG_THINKPAD_ACPI_HOTKEY_POLL=y
    # CONFIG_INTEL_MENLOW is not set
    # CONFIG_EEEPC_LAPTOP is not set
    # CONFIG_ENCLOSURE_SERVICES is not set
    # CONFIG_HP_ILO is not set
    CONFIG_HAVE_IDE=y
    CONFIG_IDE=y
    CONFIG_BLK_DEV_IDE=y

    #
    # Please see Documentation/ide/ide.txt for help/info on IDE drives
    #
    # CONFIG_BLK_DEV_IDE_SATA is not set
    CONFIG_BLK_DEV_IDEDISK=y
    CONFIG_IDEDISK_MULTI_MODE=y
    CONFIG_BLK_DEV_IDECD=y
    CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
    # CONFIG_BLK_DEV_IDETAPE is not set
    # CONFIG_BLK_DEV_IDEFLOPPY is not set
    # CONFIG_BLK_DEV_IDESCSI is not set
    CONFIG_BLK_DEV_IDEACPI=y
    # CONFIG_IDE_TASK_IOCTL is not set
    CONFIG_IDE_PROC_FS=y

    #
    # IDE chipset support/bugfixes
    #
    CONFIG_IDE_GENERIC=y
    # CONFIG_BLK_DEV_PLATFORM is not set
    # CONFIG_BLK_DEV_CMD640 is not set
    # CONFIG_BLK_DEV_IDEPNP is not set
    CONFIG_BLK_DEV_IDEDMA_SFF=y

    #
    # PCI IDE chipsets support
    #
    CONFIG_BLK_DEV_IDEPCI=y
    CONFIG_IDEPCI_PCIBUS_ORDER=y
    # CONFIG_BLK_DEV_GENERIC is not set
    # CONFIG_BLK_DEV_OPTI621 is not set
    # CONFIG_BLK_DEV_RZ1000 is not set
    CONFIG_BLK_DEV_IDEDMA_PCI=y
    # CONFIG_BLK_DEV_AEC62XX is not set
    # CONFIG_BLK_DEV_ALI15X3 is not set
    # CONFIG_BLK_DEV_AMD74XX is not set
    # CONFIG_BLK_DEV_ATIIXP is not set
    # CONFIG_BLK_DEV_CMD64X is not set
    # CONFIG_BLK_DEV_TRIFLEX is not set
    # CONFIG_BLK_DEV_CS5520 is not set
    # CONFIG_BLK_DEV_CS5530 is not set
    # CONFIG_BLK_DEV_HPT366 is not set
    # CONFIG_BLK_DEV_JMICRON is not set
    # CONFIG_BLK_DEV_SC1200 is not set
    CONFIG_BLK_DEV_PIIX=y
    # CONFIG_BLK_DEV_IT8213 is not set
    # CONFIG_BLK_DEV_IT821X is not set
    # CONFIG_BLK_DEV_NS87415 is not set
    # CONFIG_BLK_DEV_PDC202XX_OLD is not set
    # CONFIG_BLK_DEV_PDC202XX_NEW is not set
    # CONFIG_BLK_DEV_SVWKS is not set
    # CONFIG_BLK_DEV_SIIMAGE is not set
    # CONFIG_BLK_DEV_SIS5513 is not set
    # CONFIG_BLK_DEV_SLC90E66 is not set
    # CONFIG_BLK_DEV_TRM290 is not set
    # CONFIG_BLK_DEV_VIA82CXXX is not set
    # CONFIG_BLK_DEV_TC86C001 is not set
    CONFIG_BLK_DEV_IDEDMA=y

    #
    # SCSI device support
    #
    # CONFIG_RAID_ATTRS is not set
    CONFIG_SCSI=y
    CONFIG_SCSI_DMA=y
    # CONFIG_SCSI_TGT is not set
    # CONFIG_SCSI_NETLINK is not set
    # CONFIG_SCSI_PROC_FS is not set

    #
    # SCSI support type (disk, tape, CD-ROM)
    #
    CONFIG_BLK_DEV_SD=y
    # CONFIG_CHR_DEV_ST is not set
    # CONFIG_CHR_DEV_OSST is not set
    # CONFIG_BLK_DEV_SR is not set
    CONFIG_CHR_DEV_SG=y
    # CONFIG_CHR_DEV_SCH is not set

    #
    # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
    #
    # CONFIG_SCSI_MULTI_LUN is not set
    # CONFIG_SCSI_CONSTANTS is not set
    # CONFIG_SCSI_LOGGING is not set
    # CONFIG_SCSI_SCAN_ASYNC is not set
    CONFIG_SCSI_WAIT_SCAN=m

    #
    # SCSI Transports
    #
    # CONFIG_SCSI_SPI_ATTRS is not set
    # CONFIG_SCSI_FC_ATTRS is not set
    # CONFIG_SCSI_ISCSI_ATTRS is not set
    # CONFIG_SCSI_SAS_LIBSAS is not set
    # CONFIG_SCSI_SRP_ATTRS is not set
    CONFIG_SCSI_LOWLEVEL=y
    # CONFIG_ISCSI_TCP is not set
    # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
    # CONFIG_SCSI_3W_9XXX is not set
    # CONFIG_SCSI_ACARD is not set
    # CONFIG_SCSI_AACRAID is not set
    # CONFIG_SCSI_AIC7XXX is not set
    # CONFIG_SCSI_AIC7XXX_OLD is not set
    # CONFIG_SCSI_AIC79XX is not set
    # CONFIG_SCSI_AIC94XX is not set
    # CONFIG_SCSI_DPT_I2O is not set
    # CONFIG_SCSI_ADVANSYS is not set
    # CONFIG_SCSI_ARCMSR is not set
    # CONFIG_MEGARAID_NEWGEN is not set
    # CONFIG_MEGARAID_LEGACY is not set
    # CONFIG_MEGARAID_SAS is not set
    # CONFIG_SCSI_HPTIOP is not set
    # CONFIG_SCSI_BUSLOGIC is not set
    # CONFIG_SCSI_DMX3191D is not set
    # CONFIG_SCSI_EATA is not set
    # CONFIG_SCSI_FUTURE_DOMAIN is not set
    # CONFIG_SCSI_GDTH is not set
    # CONFIG_SCSI_IPS is not set
    # CONFIG_SCSI_INITIO is not set
    # CONFIG_SCSI_INIA100 is not set
    # CONFIG_SCSI_MVSAS is not set
    # CONFIG_SCSI_STEX is not set
    # CONFIG_SCSI_SYM53C8XX_2 is not set
    # CONFIG_SCSI_IPR is not set
    # CONFIG_SCSI_QLOGIC_1280 is not set
    # CONFIG_SCSI_QLA_FC is not set
    # CONFIG_SCSI_QLA_ISCSI is not set
    # CONFIG_SCSI_LPFC is not set
    # CONFIG_SCSI_DC395x is not set
    # CONFIG_SCSI_DC390T is not set
    # CONFIG_SCSI_DEBUG is not set
    # CONFIG_SCSI_SRP is not set
    # CONFIG_SCSI_DH is not set
    CONFIG_ATA=y
    # CONFIG_ATA_NONSTANDARD is not set
    CONFIG_ATA_ACPI=y
    CONFIG_SATA_PMP=y
    CONFIG_SATA_AHCI=y
    # CONFIG_SATA_SIL24 is not set
    CONFIG_ATA_SFF=y
    # CONFIG_SATA_SVW is not set
    # CONFIG_ATA_PIIX is not set
    # CONFIG_SATA_MV is not set
    # CONFIG_SATA_NV is not set
    # CONFIG_PDC_ADMA is not set
    # CONFIG_SATA_QSTOR is not set
    # CONFIG_SATA_PROMISE is not set
    # CONFIG_SATA_SX4 is not set
    # CONFIG_SATA_SIL is not set
    # CONFIG_SATA_SIS is not set
    # CONFIG_SATA_ULI is not set
    # CONFIG_SATA_VIA is not set
    # CONFIG_SATA_VITESSE is not set
    # CONFIG_SATA_INIC162X is not set
    # CONFIG_PATA_ACPI is not set
    # CONFIG_PATA_ALI is not set
    # CONFIG_PATA_AMD is not set
    # CONFIG_PATA_ARTOP is not set
    # CONFIG_PATA_ATIIXP is not set
    # CONFIG_PATA_CMD640_PCI is not set
    # CONFIG_PATA_CMD64X is not set
    # CONFIG_PATA_CS5520 is not set
    # CONFIG_PATA_CS5530 is not set
    # CONFIG_PATA_CYPRESS is not set
    # CONFIG_PATA_EFAR is not set
    # CONFIG_ATA_GENERIC is not set
    # CONFIG_PATA_HPT366 is not set
    # CONFIG_PATA_HPT37X is not set
    # CONFIG_PATA_HPT3X2N is not set
    # CONFIG_PATA_HPT3X3 is not set
    # CONFIG_PATA_IT821X is not set
    # CONFIG_PATA_IT8213 is not set
    # CONFIG_PATA_JMICRON is not set
    # CONFIG_PATA_TRIFLEX is not set
    # CONFIG_PATA_MARVELL is not set
    # CONFIG_PATA_MPIIX is not set
    # CONFIG_PATA_OLDPIIX is not set
    # CONFIG_PATA_NETCELL is not set
    # CONFIG_PATA_NINJA32 is not set
    # CONFIG_PATA_NS87410 is not set
    # CONFIG_PATA_NS87415 is not set
    # CONFIG_PATA_OPTI is not set
    # CONFIG_PATA_OPTIDMA is not set
    # CONFIG_PATA_PDC_OLD is not set
    # CONFIG_PATA_RADISYS is not set
    # CONFIG_PATA_RZ1000 is not set
    # CONFIG_PATA_SC1200 is not set
    # CONFIG_PATA_SERVERWORKS is not set
    # CONFIG_PATA_PDC2027X is not set
    # CONFIG_PATA_SIL680 is not set
    # CONFIG_PATA_SIS is not set
    # CONFIG_PATA_VIA is not set
    # CONFIG_PATA_WINBOND is not set
    # CONFIG_PATA_SCH is not set
    # CONFIG_MD is not set
    # CONFIG_FUSION is not set

    #
    # IEEE 1394 (FireWire) support
    #

    #
    # Enable only one of the two stacks, unless you know what you are doing
    #
    # CONFIG_FIREWIRE is not set
    # CONFIG_IEEE1394 is not set
    # CONFIG_I2O is not set
    # CONFIG_MACINTOSH_DRIVERS is not set
    CONFIG_NETDEVICES=y
    # CONFIG_DUMMY is not set
    # CONFIG_BONDING is not set
    # CONFIG_MACVLAN is not set
    # CONFIG_EQUALIZER is not set
    CONFIG_TUN=y
    # CONFIG_VETH is not set
    # CONFIG_NET_SB1000 is not set
    # CONFIG_ARCNET is not set
    # CONFIG_NET_ETHERNET is not set
    CONFIG_NETDEV_1000=y
    # CONFIG_ACENIC is not set
    # CONFIG_DL2K is not set
    # CONFIG_E1000 is not set
    CONFIG_E1000E=m
    # CONFIG_IP1000 is not set
    # CONFIG_IGB is not set
    # CONFIG_NS83820 is not set
    # CONFIG_HAMACHI is not set
    # CONFIG_YELLOWFIN is not set
    # CONFIG_R8169 is not set
    # CONFIG_SIS190 is not set
    # CONFIG_SKGE is not set
    # CONFIG_SKY2 is not set
    # CONFIG_VIA_VELOCITY is not set
    # CONFIG_TIGON3 is not set
    # CONFIG_BNX2 is not set
    # CONFIG_QLA3XXX is not set
    # CONFIG_ATL1 is not set
    # CONFIG_ATL1E is not set
    # CONFIG_NETDEV_10000 is not set
    # CONFIG_TR is not set

    #
    # Wireless LAN
    #
    # CONFIG_WLAN_PRE80211 is not set
    CONFIG_WLAN_80211=y
    # CONFIG_IPW2100 is not set
    # CONFIG_IPW2200 is not set
    # CONFIG_LIBERTAS is not set
    # CONFIG_AIRO is not set
    # CONFIG_HERMES is not set
    # CONFIG_ATMEL is not set
    # CONFIG_PRISM54 is not set
    # CONFIG_USB_ZD1201 is not set
    # CONFIG_USB_NET_RNDIS_WLAN is not set
    # CONFIG_RTL8180 is not set
    # CONFIG_RTL8187 is not set
    # CONFIG_ADM8211 is not set
    # CONFIG_MAC80211_HWSIM is not set
    # CONFIG_P54_COMMON is not set
    # CONFIG_ATH5K is not set
    CONFIG_IWLWIFI=m
    # CONFIG_IWLCORE is not set
    # CONFIG_IWLWIFI_LEDS is not set
    # CONFIG_IWL4965 is not set
    CONFIG_IWL3945=m
    CONFIG_IWL3945_RFKILL=y
    # CONFIG_IWL3945_SPECTRUM_MEASUREMENT is not set
    CONFIG_IWL3945_LEDS=y
    # CONFIG_IWL3945_DEBUG is not set
    # CONFIG_HOSTAP is not set
    # CONFIG_B43 is not set
    # CONFIG_B43LEGACY is not set
    # CONFIG_ZD1211RW is not set
    # CONFIG_RT2X00 is not set

    #
    # USB Network Adapters
    #
    # CONFIG_USB_CATC is not set
    # CONFIG_USB_KAWETH is not set
    # CONFIG_USB_PEGASUS is not set
    # CONFIG_USB_RTL8150 is not set
    # CONFIG_USB_USBNET is not set
    # CONFIG_USB_HSO is not set
    # CONFIG_WAN is not set
    # CONFIG_FDDI is not set
    # CONFIG_HIPPI is not set
    # CONFIG_PPP is not set
    # CONFIG_SLIP is not set
    # CONFIG_NET_FC is not set
    # CONFIG_NETCONSOLE is not set
    # CONFIG_NETPOLL is not set
    # CONFIG_NET_POLL_CONTROLLER is not set
    # CONFIG_ISDN is not set
    # CONFIG_PHONE is not set

    #
    # Input device support
    #
    CONFIG_INPUT=y
    # CONFIG_INPUT_FF_MEMLESS is not set
    # CONFIG_INPUT_POLLDEV is not set

    #
    # Userland interfaces
    #
    CONFIG_INPUT_MOUSEDEV=y
    # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
    CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
    CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
    # CONFIG_INPUT_JOYDEV is not set
    CONFIG_INPUT_EVDEV=y
    # CONFIG_INPUT_EVBUG is not set

    #
    # Input Device Drivers
    #
    CONFIG_INPUT_KEYBOARD=y
    CONFIG_KEYBOARD_ATKBD=y
    # CONFIG_KEYBOARD_SUNKBD is not set
    # CONFIG_KEYBOARD_LKKBD is not set
    # CONFIG_KEYBOARD_XTKBD is not set
    # CONFIG_KEYBOARD_NEWTON is not set
    # CONFIG_KEYBOARD_STOWAWAY is not set
    CONFIG_INPUT_MOUSE=y
    CONFIG_MOUSE_PS2=y
    CONFIG_MOUSE_PS2_ALPS=y
    CONFIG_MOUSE_PS2_LOGIPS2PP=y
    CONFIG_MOUSE_PS2_SYNAPTICS=y
    CONFIG_MOUSE_PS2_LIFEBOOK=y
    CONFIG_MOUSE_PS2_TRACKPOINT=y
    # CONFIG_MOUSE_PS2_TOUCHKIT is not set
    # CONFIG_MOUSE_SERIAL is not set
    # CONFIG_MOUSE_APPLETOUCH is not set
    # CONFIG_MOUSE_VSXXXAA is not set
    # CONFIG_INPUT_JOYSTICK is not set
    # CONFIG_INPUT_TABLET is not set
    # CONFIG_INPUT_TOUCHSCREEN is not set
    # CONFIG_INPUT_MISC is not set

    #
    # Hardware I/O ports
    #
    CONFIG_SERIO=y
    CONFIG_SERIO_I8042=y
    # CONFIG_SERIO_SERPORT is not set
    # CONFIG_SERIO_CT82C710 is not set
    # CONFIG_SERIO_PCIPS2 is not set
    CONFIG_SERIO_LIBPS2=y
    # CONFIG_SERIO_RAW is not set
    # CONFIG_GAMEPORT is not set

    #
    # Character devices
    #
    CONFIG_VT=y
    CONFIG_CONSOLE_TRANSLATIONS=y
    CONFIG_VT_CONSOLE=y
    CONFIG_HW_CONSOLE=y
    # CONFIG_VT_HW_CONSOLE_BINDING is not set
    CONFIG_DEVKMEM=y
    # CONFIG_SERIAL_NONSTANDARD is not set
    # CONFIG_NOZOMI is not set

    #
    # Serial drivers
    #
    CONFIG_SERIAL_8250=y
    CONFIG_SERIAL_8250_CONSOLE=y
    CONFIG_FIX_EARLYCON_MEM=y
    CONFIG_SERIAL_8250_PCI=y
    CONFIG_SERIAL_8250_PNP=y
    CONFIG_SERIAL_8250_NR_UARTS=4
    CONFIG_SERIAL_8250_RUNTIME_UARTS=4
    # CONFIG_SERIAL_8250_EXTENDED is not set

    #
    # Non-8250 serial port support
    #
    CONFIG_SERIAL_CORE=y
    CONFIG_SERIAL_CORE_CONSOLE=y
    # CONFIG_SERIAL_JSM is not set
    CONFIG_UNIX98_PTYS=y
    CONFIG_LEGACY_PTYS=y
    CONFIG_LEGACY_PTY_COUNT=256
    # CONFIG_IPMI_HANDLER is not set
    # CONFIG_HW_RANDOM is not set
    CONFIG_NVRAM=y
    CONFIG_RTC=y
    # CONFIG_R3964 is not set
    # CONFIG_APPLICOM is not set
    # CONFIG_MWAVE is not set
    # CONFIG_PC8736x_GPIO is not set
    # CONFIG_RAW_DRIVER is not set
    CONFIG_HPET=y
    CONFIG_HPET_RTC_IRQ=y
    CONFIG_HPET_MMAP=y
    # CONFIG_HANGCHECK_TIMER is not set
    # CONFIG_TCG_TPM is not set
    # CONFIG_TELCLOCK is not set
    CONFIG_DEVPORT=y
    # CONFIG_I2C is not set
    # CONFIG_SPI is not set
    CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
    # CONFIG_GPIOLIB is not set
    # CONFIG_W1 is not set
    CONFIG_POWER_SUPPLY=y
    # CONFIG_POWER_SUPPLY_DEBUG is not set
    # CONFIG_PDA_POWER is not set
    # CONFIG_BATTERY_DS2760 is not set
    CONFIG_HWMON=y
    # CONFIG_HWMON_VID is not set
    # CONFIG_SENSORS_ABITUGURU is not set
    # CONFIG_SENSORS_ABITUGURU3 is not set
    # CONFIG_SENSORS_K8TEMP is not set
    # CONFIG_SENSORS_I5K_AMB is not set
    # CONFIG_SENSORS_F71805F is not set
    # CONFIG_SENSORS_F71882FG is not set
    CONFIG_SENSORS_CORETEMP=y
    # CONFIG_SENSORS_IT87 is not set
    # CONFIG_SENSORS_PC87360 is not set
    # CONFIG_SENSORS_PC87427 is not set
    # CONFIG_SENSORS_SIS5595 is not set
    # CONFIG_SENSORS_SMSC47M1 is not set
    # CONFIG_SENSORS_SMSC47B397 is not set
    # CONFIG_SENSORS_VIA686A is not set
    # CONFIG_SENSORS_VT1211 is not set
    # CONFIG_SENSORS_VT8231 is not set
    # CONFIG_SENSORS_W83627HF is not set
    # CONFIG_SENSORS_W83627EHF is not set
    # CONFIG_SENSORS_HDAPS is not set
    # CONFIG_SENSORS_APPLESMC is not set
    # CONFIG_HWMON_DEBUG_CHIP is not set
    CONFIG_THERMAL=y
    # CONFIG_THERMAL_HWMON is not set
    # CONFIG_WATCHDOG is not set

    #
    # Sonics Silicon Backplane
    #
    CONFIG_SSB_POSSIBLE=y
    # CONFIG_SSB is not set

    #
    # Multifunction device drivers
    #
    # CONFIG_MFD_CORE is not set
    # CONFIG_MFD_SM501 is not set
    # CONFIG_HTC_PASIC3 is not set

    #
    # Multimedia devices
    #

    #
    # Multimedia core support
    #
    # CONFIG_VIDEO_DEV is not set
    # CONFIG_DVB_CORE is not set
    # CONFIG_VIDEO_MEDIA is not set

    #
    # Multimedia drivers
    #
    # CONFIG_DAB is not set

    #
    # Graphics support
    #
    CONFIG_AGP=y
    CONFIG_AGP_AMD64=y
    # CONFIG_AGP_INTEL is not set
    # CONFIG_AGP_SIS is not set
    # CONFIG_AGP_VIA is not set
    # CONFIG_DRM is not set
    # CONFIG_VGASTATE is not set
    # CONFIG_VIDEO_OUTPUT_CONTROL is not set
    CONFIG_FB=y
    # CONFIG_FIRMWARE_EDID is not set
    # CONFIG_FB_DDC is not set
    CONFIG_FB_CFB_FILLRECT=y
    CONFIG_FB_CFB_COPYAREA=y
    CONFIG_FB_CFB_IMAGEBLIT=y
    # CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
    # CONFIG_FB_SYS_FILLRECT is not set
    # CONFIG_FB_SYS_COPYAREA is not set
    # CONFIG_FB_SYS_IMAGEBLIT is not set
    # CONFIG_FB_FOREIGN_ENDIAN is not set
    # CONFIG_FB_SYS_FOPS is not set
    # CONFIG_FB_SVGALIB is not set
    # CONFIG_FB_MACMODES is not set
    # CONFIG_FB_BACKLIGHT is not set
    # CONFIG_FB_MODE_HELPERS is not set
    # CONFIG_FB_TILEBLITTING is not set

    #
    # Frame buffer hardware drivers
    #
    # CONFIG_FB_CIRRUS is not set
    # CONFIG_FB_PM2 is not set
    # CONFIG_FB_CYBER2000 is not set
    # CONFIG_FB_ARC is not set
    # CONFIG_FB_ASILIANT is not set
    # CONFIG_FB_IMSTT is not set
    # CONFIG_FB_VGA16 is not set
    CONFIG_FB_VESA=y
    # CONFIG_FB_EFI is not set
    # CONFIG_FB_N411 is not set
    # CONFIG_FB_HGA is not set
    # CONFIG_FB_S1D13XXX is not set
    # CONFIG_FB_NVIDIA is not set
    # CONFIG_FB_RIVA is not set
    # CONFIG_FB_LE80578 is not set
    # CONFIG_FB_INTEL is not set
    # CONFIG_FB_MATROX is not set
    # CONFIG_FB_RADEON is not set
    # CONFIG_FB_ATY128 is not set
    # CONFIG_FB_ATY is not set
    # CONFIG_FB_S3 is not set
    # CONFIG_FB_SAVAGE is not set
    # CONFIG_FB_SIS is not set
    # CONFIG_FB_NEOMAGIC is not set
    # CONFIG_FB_KYRO is not set
    # CONFIG_FB_3DFX is not set
    # CONFIG_FB_VOODOO1 is not set
    # CONFIG_FB_VT8623 is not set
    # CONFIG_FB_TRIDENT is not set
    # CONFIG_FB_ARK is not set
    # CONFIG_FB_PM3 is not set
    # CONFIG_FB_CARMINE is not set
    # CONFIG_FB_GEODE is not set
    # CONFIG_FB_VIRTUAL is not set
    CONFIG_BACKLIGHT_LCD_SUPPORT=y
    CONFIG_LCD_CLASS_DEVICE=m
    # CONFIG_LCD_ILI9320 is not set
    # CONFIG_LCD_PLATFORM is not set
    CONFIG_BACKLIGHT_CLASS_DEVICE=m
    # CONFIG_BACKLIGHT_CORGI is not set
    # CONFIG_BACKLIGHT_PROGEAR is not set
    # CONFIG_BACKLIGHT_MBP_NVIDIA is not set

    #
    # Display device support
    #
    # CONFIG_DISPLAY_SUPPORT is not set

    #
    # Console display driver support
    #
    CONFIG_VGA_CONSOLE=y
    CONFIG_VGACON_SOFT_SCROLLBACK=y
    CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=128
    CONFIG_VIDEO_SELECT=y
    CONFIG_DUMMY_CONSOLE=y
    CONFIG_FRAMEBUFFER_CONSOLE=y
    # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
    # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
    # CONFIG_FONTS is not set
    CONFIG_FONT_8x8=y
    CONFIG_FONT_8x16=y
    # CONFIG_LOGO is not set
    CONFIG_SOUND=y
    CONFIG_SND=y
    CONFIG_SND_TIMER=y
    CONFIG_SND_PCM=y
    CONFIG_SND_HWDEP=y
    # CONFIG_SND_SEQUENCER is not set
    CONFIG_SND_OSSEMUL=y
    CONFIG_SND_MIXER_OSS=y
    CONFIG_SND_PCM_OSS=y
    CONFIG_SND_PCM_OSS_PLUGINS=y
    # CONFIG_SND_RTCTIMER is not set
    # CONFIG_SND_DYNAMIC_MINORS is not set
    CONFIG_SND_SUPPORT_OLD_API=y
    CONFIG_SND_VERBOSE_PROCFS=y
    # CONFIG_SND_VERBOSE_PRINTK is not set
    # CONFIG_SND_DEBUG is not set
    CONFIG_SND_VMASTER=y
    CONFIG_SND_DRIVERS=y
    # CONFIG_SND_PCSP is not set
    # CONFIG_SND_DUMMY is not set
    # CONFIG_SND_MTPAV is not set
    # CONFIG_SND_SERIAL_U16550 is not set
    # CONFIG_SND_MPU401 is not set
    CONFIG_SND_PCI=y
    # CONFIG_SND_AD1889 is not set
    # CONFIG_SND_ALS300 is not set
    # CONFIG_SND_ALS4000 is not set
    # CONFIG_SND_ALI5451 is not set
    # CONFIG_SND_ATIIXP is not set
    # CONFIG_SND_ATIIXP_MODEM is not set
    # CONFIG_SND_AU8810 is not set
    # CONFIG_SND_AU8820 is not set
    # CONFIG_SND_AU8830 is not set
    # CONFIG_SND_AW2 is not set
    # CONFIG_SND_AZT3328 is not set
    # CONFIG_SND_BT87X is not set
    # CONFIG_SND_CA0106 is not set
    # CONFIG_SND_CMIPCI is not set
    # CONFIG_SND_OXYGEN is not set
    # CONFIG_SND_CS4281 is not set
    # CONFIG_SND_CS46XX is not set
    # CONFIG_SND_CS5530 is not set
    # CONFIG_SND_DARLA20 is not set
    # CONFIG_SND_GINA20 is not set
    # CONFIG_SND_LAYLA20 is not set
    # CONFIG_SND_DARLA24 is not set
    # CONFIG_SND_GINA24 is not set
    # CONFIG_SND_LAYLA24 is not set
    # CONFIG_SND_MONA is not set
    # CONFIG_SND_MIA is not set
    # CONFIG_SND_ECHO3G is not set
    # CONFIG_SND_INDIGO is not set
    # CONFIG_SND_INDIGOIO is not set
    # CONFIG_SND_INDIGODJ is not set
    # CONFIG_SND_EMU10K1 is not set
    # CONFIG_SND_EMU10K1X is not set
    # CONFIG_SND_ENS1370 is not set
    # CONFIG_SND_ENS1371 is not set
    # CONFIG_SND_ES1938 is not set
    # CONFIG_SND_ES1968 is not set
    # CONFIG_SND_FM801 is not set
    CONFIG_SND_HDA_INTEL=y
    CONFIG_SND_HDA_HWDEP=y
    # CONFIG_SND_HDA_CODEC_REALTEK is not set
    CONFIG_SND_HDA_CODEC_ANALOG=y
    # CONFIG_SND_HDA_CODEC_SIGMATEL is not set
    # CONFIG_SND_HDA_CODEC_VIA is not set
    # CONFIG_SND_HDA_CODEC_ATIHDMI is not set
    # CONFIG_SND_HDA_CODEC_CONEXANT is not set
    # CONFIG_SND_HDA_CODEC_CMEDIA is not set
    # CONFIG_SND_HDA_CODEC_SI3054 is not set
    CONFIG_SND_HDA_GENERIC=y
    CONFIG_SND_HDA_POWER_SAVE=y
    CONFIG_SND_HDA_POWER_SAVE_DEFAULT=10
    # CONFIG_SND_HDSP is not set
    # CONFIG_SND_HDSPM is not set
    # CONFIG_SND_HIFIER is not set
    # CONFIG_SND_ICE1712 is not set
    # CONFIG_SND_ICE1724 is not set
    # CONFIG_SND_INTEL8X0 is not set
    # CONFIG_SND_INTEL8X0M is not set
    # CONFIG_SND_KORG1212 is not set
    # CONFIG_SND_MAESTRO3 is not set
    # CONFIG_SND_MIXART is not set
    # CONFIG_SND_NM256 is not set
    # CONFIG_SND_PCXHR is not set
    # CONFIG_SND_RIPTIDE is not set
    # CONFIG_SND_RME32 is not set
    # CONFIG_SND_RME96 is not set
    # CONFIG_SND_RME9652 is not set
    # CONFIG_SND_SONICVIBES is not set
    # CONFIG_SND_TRIDENT is not set
    # CONFIG_SND_VIA82XX is not set
    # CONFIG_SND_VIA82XX_MODEM is not set
    # CONFIG_SND_VIRTUOSO is not set
    # CONFIG_SND_VX222 is not set
    # CONFIG_SND_YMFPCI is not set
    CONFIG_SND_USB=y
    # CONFIG_SND_USB_AUDIO is not set
    # CONFIG_SND_USB_USX2Y is not set
    # CONFIG_SND_USB_CAIAQ is not set
    # CONFIG_SND_SOC is not set
    # CONFIG_SOUND_PRIME is not set
    CONFIG_HID_SUPPORT=y
    CONFIG_HID=y
    # CONFIG_HID_DEBUG is not set
    CONFIG_HIDRAW=y

    #
    # USB Input Devices
    #
    CONFIG_USB_HID=y
    # CONFIG_USB_HIDINPUT_POWERBOOK is not set
    # CONFIG_HID_FF is not set
    # CONFIG_USB_HIDDEV is not set
    CONFIG_USB_SUPPORT=y
    CONFIG_USB_ARCH_HAS_HCD=y
    CONFIG_USB_ARCH_HAS_OHCI=y
    CONFIG_USB_ARCH_HAS_EHCI=y
    CONFIG_USB=y
    CONFIG_USB_DEBUG=y
    # CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

    #
    # Miscellaneous USB options
    #
    CONFIG_USB_DEVICEFS=y
    CONFIG_USB_DEVICE_CLASS=y
    # CONFIG_USB_DYNAMIC_MINORS is not set
    CONFIG_USB_SUSPEND=y
    # CONFIG_USB_OTG is not set

    #
    # USB Host Controller Drivers
    #
    # CONFIG_USB_C67X00_HCD is not set
    CONFIG_USB_EHCI_HCD=y
    # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
    # CONFIG_USB_EHCI_TT_NEWSCHED is not set
    # CONFIG_USB_ISP116X_HCD is not set
    # CONFIG_USB_ISP1760_HCD is not set
    # CONFIG_USB_OHCI_HCD is not set
    CONFIG_USB_UHCI_HCD=y
    # CONFIG_USB_SL811_HCD is not set
    # CONFIG_USB_R8A66597_HCD is not set

    #
    # USB Device Class drivers
    #
    # CONFIG_USB_ACM is not set
    # CONFIG_USB_PRINTER is not set
    # CONFIG_USB_WDM is not set

    #
    # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
    #

    #
    # may also be needed; see USB_STORAGE Help for more information
    #
    CONFIG_USB_STORAGE=m
    # CONFIG_USB_STORAGE_DEBUG is not set
    # CONFIG_USB_STORAGE_DATAFAB is not set
    # CONFIG_USB_STORAGE_FREECOM is not set
    # CONFIG_USB_STORAGE_ISD200 is not set
    # CONFIG_USB_STORAGE_DPCM is not set
    # CONFIG_USB_STORAGE_USBAT is not set
    # CONFIG_USB_STORAGE_SDDR09 is not set
    # CONFIG_USB_STORAGE_SDDR55 is not set
    # CONFIG_USB_STORAGE_JUMPSHOT is not set
    # CONFIG_USB_STORAGE_ALAUDA is not set
    # CONFIG_USB_STORAGE_ONETOUCH is not set
    # CONFIG_USB_STORAGE_KARMA is not set
    # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
    # CONFIG_USB_LIBUSUAL is not set

    #
    # USB Imaging devices
    #
    # CONFIG_USB_MDC800 is not set
    # CONFIG_USB_MICROTEK is not set
    CONFIG_USB_MON=y

    #
    # USB port drivers
    #
    # CONFIG_USB_SERIAL is not set

    #
    # USB Miscellaneous drivers
    #
    # CONFIG_USB_EMI62 is not set
    # CONFIG_USB_EMI26 is not set
    # CONFIG_USB_ADUTUX is not set
    # CONFIG_USB_AUERSWALD is not set
    # CONFIG_USB_RIO500 is not set
    # CONFIG_USB_LEGOTOWER is not set
    # CONFIG_USB_LCD is not set
    # CONFIG_USB_BERRY_CHARGE is not set
    # CONFIG_USB_LED is not set
    # CONFIG_USB_CYPRESS_CY7C63 is not set
    # CONFIG_USB_CYTHERM is not set
    # CONFIG_USB_PHIDGET is not set
    # CONFIG_USB_IDMOUSE is not set
    # CONFIG_USB_FTDI_ELAN is not set
    # CONFIG_USB_APPLEDISPLAY is not set
    # CONFIG_USB_SISUSBVGA is not set
    # CONFIG_USB_LD is not set
    # CONFIG_USB_TRANCEVIBRATOR is not set
    # CONFIG_USB_IOWARRIOR is not set
    # CONFIG_USB_TEST is not set
    # CONFIG_USB_ISIGHTFW is not set
    # CONFIG_USB_GADGET is not set
    # CONFIG_MMC is not set
    # CONFIG_MEMSTICK is not set
    CONFIG_NEW_LEDS=y
    CONFIG_LEDS_CLASS=m

    #
    # LED drivers
    #
    # CONFIG_LEDS_CLEVO_MAIL is not set

    #
    # LED Triggers
    #
    CONFIG_LEDS_TRIGGERS=y
    # CONFIG_LEDS_TRIGGER_TIMER is not set
    # CONFIG_LEDS_TRIGGER_IDE_DISK is not set
    # CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
    # CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
    # CONFIG_ACCESSIBILITY is not set
    # CONFIG_INFINIBAND is not set
    # CONFIG_EDAC is not set
    # CONFIG_RTC_CLASS is not set
    # CONFIG_DMADEVICES is not set
    # CONFIG_UIO is not set

    #
    # Firmware Drivers
    #
    # CONFIG_EDD is not set
    CONFIG_FIRMWARE_MEMMAP=y
    # CONFIG_DELL_RBU is not set
    # CONFIG_DCDBAS is not set
    CONFIG_DMIID=y
    # CONFIG_ISCSI_IBFT_FIND is not set

    #
    # File systems
    #
    # CONFIG_EXT2_FS is not set
    CONFIG_EXT3_FS=y
    CONFIG_EXT3_FS_XATTR=y
    CONFIG_EXT3_FS_POSIX_ACL=y
    CONFIG_EXT3_FS_SECURITY=y
    # CONFIG_EXT4DEV_FS is not set
    CONFIG_JBD=y
    # CONFIG_JBD_DEBUG is not set
    CONFIG_FS_MBCACHE=y
    # CONFIG_REISERFS_FS is not set
    # CONFIG_JFS_FS is not set
    CONFIG_FS_POSIX_ACL=y
    # CONFIG_XFS_FS is not set
    # CONFIG_GFS2_FS is not set
    # CONFIG_OCFS2_FS is not set
    CONFIG_DNOTIFY=y
    CONFIG_INOTIFY=y
    CONFIG_INOTIFY_USER=y
    # CONFIG_QUOTA is not set
    # CONFIG_AUTOFS_FS is not set
    # CONFIG_AUTOFS4_FS is not set
    CONFIG_FUSE_FS=m
    CONFIG_GENERIC_ACL=y

    #
    # CD-ROM/DVD Filesystems
    #
    CONFIG_ISO9660_FS=m
    CONFIG_JOLIET=y
    # CONFIG_ZISOFS is not set
    CONFIG_UDF_FS=m
    CONFIG_UDF_NLS=y

    #
    # DOS/FAT/NT Filesystems
    #
    CONFIG_FAT_FS=m
    CONFIG_MSDOS_FS=m
    CONFIG_VFAT_FS=m
    CONFIG_FAT_DEFAULT_CODEPAGE=437
    CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
    # CONFIG_NTFS_FS is not set

    #
    # Pseudo filesystems
    #
    CONFIG_PROC_FS=y
    CONFIG_PROC_KCORE=y
    CONFIG_PROC_SYSCTL=y
    CONFIG_SYSFS=y
    CONFIG_TMPFS=y
    CONFIG_TMPFS_POSIX_ACL=y
    # CONFIG_HUGETLBFS is not set
    # CONFIG_HUGETLB_PAGE is not set
    # CONFIG_CONFIGFS_FS is not set

    #
    # Miscellaneous filesystems
    #
    # CONFIG_ADFS_FS is not set
    # CONFIG_AFFS_FS is not set
    # CONFIG_HFS_FS is not set
    # CONFIG_HFSPLUS_FS is not set
    # CONFIG_BEFS_FS is not set
    # CONFIG_BFS_FS is not set
    # CONFIG_EFS_FS is not set
    # CONFIG_CRAMFS is not set
    # CONFIG_VXFS_FS is not set
    # CONFIG_MINIX_FS is not set
    # CONFIG_OMFS_FS is not set
    # CONFIG_HPFS_FS is not set
    # CONFIG_QNX4FS_FS is not set
    # CONFIG_ROMFS_FS is not set
    # CONFIG_SYSV_FS is not set
    # CONFIG_UFS_FS is not set
    CONFIG_NETWORK_FILESYSTEMS=y
    CONFIG_NFS_FS=m
    CONFIG_NFS_V3=y
    CONFIG_NFS_V3_ACL=y
    # CONFIG_NFS_V4 is not set
    CONFIG_NFSD=m
    CONFIG_NFSD_V2_ACL=y
    CONFIG_NFSD_V3=y
    CONFIG_NFSD_V3_ACL=y
    # CONFIG_NFSD_V4 is not set
    CONFIG_LOCKD=m
    CONFIG_LOCKD_V4=y
    CONFIG_EXPORTFS=m
    CONFIG_NFS_ACL_SUPPORT=m
    CONFIG_NFS_COMMON=y
    CONFIG_SUNRPC=m
    CONFIG_SUNRPC_GSS=m
    CONFIG_RPCSEC_GSS_KRB5=m
    # CONFIG_RPCSEC_GSS_SPKM3 is not set
    # CONFIG_SMB_FS is not set
    # CONFIG_CIFS is not set
    # CONFIG_NCP_FS is not set
    # CONFIG_CODA_FS is not set
    # CONFIG_AFS_FS is not set

    #
    # Partition Types
    #
    # CONFIG_PARTITION_ADVANCED is not set
    CONFIG_MSDOS_PARTITION=y
    CONFIG_NLS=m
    CONFIG_NLS_DEFAULT="iso8859-1"
    CONFIG_NLS_CODEPAGE_437=m
    # CONFIG_NLS_CODEPAGE_737 is not set
    # CONFIG_NLS_CODEPAGE_775 is not set
    # CONFIG_NLS_CODEPAGE_850 is not set
    # CONFIG_NLS_CODEPAGE_852 is not set
    # CONFIG_NLS_CODEPAGE_855 is not set
    # CONFIG_NLS_CODEPAGE_857 is not set
    # CONFIG_NLS_CODEPAGE_860 is not set
    # CONFIG_NLS_CODEPAGE_861 is not set
    # CONFIG_NLS_CODEPAGE_862 is not set
    # CONFIG_NLS_CODEPAGE_863 is not set
    # CONFIG_NLS_CODEPAGE_864 is not set
    # CONFIG_NLS_CODEPAGE_865 is not set
    # CONFIG_NLS_CODEPAGE_866 is not set
    # CONFIG_NLS_CODEPAGE_869 is not set
    # CONFIG_NLS_CODEPAGE_936 is not set
    # CONFIG_NLS_CODEPAGE_950 is not set
    # CONFIG_NLS_CODEPAGE_932 is not set
    # CONFIG_NLS_CODEPAGE_949 is not set
    # CONFIG_NLS_CODEPAGE_874 is not set
    # CONFIG_NLS_ISO8859_8 is not set
    # CONFIG_NLS_CODEPAGE_1250 is not set
    # CONFIG_NLS_CODEPAGE_1251 is not set
    # CONFIG_NLS_ASCII is not set
    CONFIG_NLS_ISO8859_1=m
    # CONFIG_NLS_ISO8859_2 is not set
    # CONFIG_NLS_ISO8859_3 is not set
    # CONFIG_NLS_ISO8859_4 is not set
    # CONFIG_NLS_ISO8859_5 is not set
    # CONFIG_NLS_ISO8859_6 is not set
    # CONFIG_NLS_ISO8859_7 is not set
    # CONFIG_NLS_ISO8859_9 is not set
    # CONFIG_NLS_ISO8859_13 is not set
    # CONFIG_NLS_ISO8859_14 is not set
    # CONFIG_NLS_ISO8859_15 is not set
    # CONFIG_NLS_KOI8_R is not set
    # CONFIG_NLS_KOI8_U is not set
    # CONFIG_NLS_UTF8 is not set
    # CONFIG_DLM is not set

    #
    # Kernel hacking
    #
    CONFIG_TRACE_IRQFLAGS_SUPPORT=y
    CONFIG_PRINTK_TIME=y
    CONFIG_ENABLE_WARN_DEPRECATED=y
    # CONFIG_ENABLE_MUST_CHECK is not set
    CONFIG_FRAME_WARN=2048
    CONFIG_MAGIC_SYSRQ=y
    CONFIG_UNUSED_SYMBOLS=y
    CONFIG_DEBUG_FS=y
    # CONFIG_HEADERS_CHECK is not set
    CONFIG_DEBUG_KERNEL=y
    # CONFIG_DEBUG_SHIRQ is not set
    CONFIG_DETECT_SOFTLOCKUP=y
    # CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
    CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
    CONFIG_SCHED_DEBUG=y
    CONFIG_SCHEDSTATS=y
    CONFIG_TIMER_STATS=y
    # CONFIG_DEBUG_OBJECTS is not set
    CONFIG_DEBUG_SLAB=y
    CONFIG_DEBUG_SLAB_LEAK=y
    # CONFIG_DEBUG_RT_MUTEXES is not set
    # CONFIG_RT_MUTEX_TESTER is not set
    CONFIG_DEBUG_SPINLOCK=y
    CONFIG_DEBUG_MUTEXES=y
    CONFIG_DEBUG_LOCK_ALLOC=y
    CONFIG_PROVE_LOCKING=y
    CONFIG_LOCKDEP=y
    CONFIG_LOCK_STAT=y
    # CONFIG_DEBUG_LOCKDEP is not set
    CONFIG_TRACE_IRQFLAGS=y
    CONFIG_DEBUG_SPINLOCK_SLEEP=y
    CONFIG_DEBUG_LOCKING_API_SELFTESTS=y
    CONFIG_STACKTRACE=y
    # CONFIG_DEBUG_KOBJECT is not set
    CONFIG_DEBUG_BUGVERBOSE=y
    # CONFIG_DEBUG_INFO is not set
    CONFIG_DEBUG_VM=y
    CONFIG_DEBUG_WRITECOUNT=y
    CONFIG_DEBUG_MEMORY_INIT=y
    CONFIG_DEBUG_LIST=y
    # CONFIG_DEBUG_SG is not set
    CONFIG_FRAME_POINTER=y
    # CONFIG_BOOT_PRINTK_DELAY is not set
    # CONFIG_RCU_TORTURE_TEST is not set
    # CONFIG_BACKTRACE_SELF_TEST is not set
    # CONFIG_FAULT_INJECTION is not set
    CONFIG_LATENCYTOP=y
    CONFIG_HAVE_FTRACE=y
    CONFIG_HAVE_DYNAMIC_FTRACE=y
    # CONFIG_FTRACE is not set
    # CONFIG_IRQSOFF_TRACER is not set
    # CONFIG_SYSPROF_TRACER is not set
    # CONFIG_SCHED_TRACER is not set
    # CONFIG_CONTEXT_SWITCH_TRACER is not set
    # CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
    # CONFIG_SAMPLES is not set
    CONFIG_HAVE_ARCH_KGDB=y
    # CONFIG_KGDB is not set
    CONFIG_STRICT_DEVMEM=y
    CONFIG_X86_VERBOSE_BOOTUP=y
    CONFIG_EARLY_PRINTK=y
    CONFIG_DEBUG_STACKOVERFLOW=y
    # CONFIG_DEBUG_STACK_USAGE is not set
    # CONFIG_DEBUG_PAGEALLOC is not set
    # CONFIG_DEBUG_PER_CPU_MAPS is not set
    # CONFIG_X86_PTDUMP is not set
    CONFIG_DEBUG_RODATA=y
    # CONFIG_DIRECT_GBPAGES is not set
    # CONFIG_DEBUG_RODATA_TEST is not set
    # CONFIG_DEBUG_NX_TEST is not set
    # CONFIG_IOMMU_DEBUG is not set
    # CONFIG_MMIOTRACE is not set
    CONFIG_IO_DELAY_TYPE_0X80=0
    CONFIG_IO_DELAY_TYPE_0XED=1
    CONFIG_IO_DELAY_TYPE_UDELAY=2
    CONFIG_IO_DELAY_TYPE_NONE=3
    CONFIG_IO_DELAY_0X80=y
    # CONFIG_IO_DELAY_0XED is not set
    # CONFIG_IO_DELAY_UDELAY is not set
    # CONFIG_IO_DELAY_NONE is not set
    CONFIG_DEFAULT_IO_DELAY_TYPE=0
    # CONFIG_DEBUG_BOOT_PARAMS is not set
    # CONFIG_CPA_DEBUG is not set
    # CONFIG_OPTIMIZE_INLINING is not set

    #
    # Security options
    #
    # CONFIG_KEYS is not set
    # CONFIG_SECURITY is not set
    # CONFIG_SECURITY_FILE_CAPABILITIES is not set
    CONFIG_CRYPTO=y

    #
    # Crypto core or helper
    #
    CONFIG_CRYPTO_ALGAPI=y
    CONFIG_CRYPTO_BLKCIPHER=y
    CONFIG_CRYPTO_MANAGER=y
    # CONFIG_CRYPTO_GF128MUL is not set
    # CONFIG_CRYPTO_NULL is not set
    # CONFIG_CRYPTO_CRYPTD is not set
    # CONFIG_CRYPTO_AUTHENC is not set
    # CONFIG_CRYPTO_TEST is not set

    #
    # Authenticated Encryption with Associated Data
    #
    # CONFIG_CRYPTO_CCM is not set
    # CONFIG_CRYPTO_GCM is not set
    # CONFIG_CRYPTO_SEQIV is not set

    #
    # Block modes
    #
    CONFIG_CRYPTO_CBC=m
    # CONFIG_CRYPTO_CTR is not set
    # CONFIG_CRYPTO_CTS is not set
    CONFIG_CRYPTO_ECB=y
    # CONFIG_CRYPTO_LRW is not set
    # CONFIG_CRYPTO_PCBC is not set
    # CONFIG_CRYPTO_XTS is not set

    #
    # Hash modes
    #
    # CONFIG_CRYPTO_HMAC is not set
    # CONFIG_CRYPTO_XCBC is not set

    #
    # Digest
    #
    # CONFIG_CRYPTO_CRC32C is not set
    # CONFIG_CRYPTO_MD4 is not set
    CONFIG_CRYPTO_MD5=m
    CONFIG_CRYPTO_MICHAEL_MIC=y
    # CONFIG_CRYPTO_RMD128 is not set
    # CONFIG_CRYPTO_RMD160 is not set
    # CONFIG_CRYPTO_RMD256 is not set
    # CONFIG_CRYPTO_RMD320 is not set
    # CONFIG_CRYPTO_SHA1 is not set
    # CONFIG_CRYPTO_SHA256 is not set
    # CONFIG_CRYPTO_SHA512 is not set
    # CONFIG_CRYPTO_TGR192 is not set
    # CONFIG_CRYPTO_WP512 is not set

    #
    # Ciphers
    #
    CONFIG_CRYPTO_AES=y
    CONFIG_CRYPTO_AES_X86_64=y
    # CONFIG_CRYPTO_ANUBIS is not set
    CONFIG_CRYPTO_ARC4=y
    # CONFIG_CRYPTO_BLOWFISH is not set
    # CONFIG_CRYPTO_CAMELLIA is not set
    # CONFIG_CRYPTO_CAST5 is not set
    # CONFIG_CRYPTO_CAST6 is not set
    CONFIG_CRYPTO_DES=m
    # CONFIG_CRYPTO_FCRYPT is not set
    # CONFIG_CRYPTO_KHAZAD is not set
    # CONFIG_CRYPTO_SALSA20 is not set
    # CONFIG_CRYPTO_SALSA20_X86_64 is not set
    # CONFIG_CRYPTO_SEED is not set
    # CONFIG_CRYPTO_SERPENT is not set
    # CONFIG_CRYPTO_TEA is not set
    # CONFIG_CRYPTO_TWOFISH is not set
    # CONFIG_CRYPTO_TWOFISH_X86_64 is not set

    #
    # Compression
    #
    # CONFIG_CRYPTO_DEFLATE is not set
    # CONFIG_CRYPTO_LZO is not set
    CONFIG_CRYPTO_HW=y
    # CONFIG_CRYPTO_DEV_HIFN_795X is not set
    CONFIG_HAVE_KVM=y
    CONFIG_VIRTUALIZATION=y
    CONFIG_KVM=m
    CONFIG_KVM_INTEL=m
    # CONFIG_KVM_AMD is not set
    # CONFIG_VIRTIO_PCI is not set
    # CONFIG_VIRTIO_BALLOON is not set

    #
    # Library routines
    #
    CONFIG_BITREVERSE=y
    CONFIG_GENERIC_FIND_FIRST_BIT=y
    CONFIG_GENERIC_FIND_NEXT_BIT=y
    # CONFIG_CRC_CCITT is not set
    # CONFIG_CRC16 is not set
    CONFIG_CRC_T10DIF=y
    CONFIG_CRC_ITU_T=m
    CONFIG_CRC32=y
    # CONFIG_CRC7 is not set
    # CONFIG_LIBCRC32C is not set
    CONFIG_PLIST=y
    CONFIG_HAS_IOMEM=y
    CONFIG_HAS_IOPORT=y
    CONFIG_HAS_DMA=y
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  4. Re: [bug] 2.6.27-rc1: I/O errors after resume

    On Thursday, 31 of July 2008, Miklos Szeredi wrote:
    > With 2.6.27-rc1 things break badly after resume on my T60. Dmesg and
    > config attached. 2.6.26 worked fine.


    Ugh, lots of stuff in a single message.

    Anyway, can you try the current -git and report back, please? It's possible
    that this has been fixed already.

    Thanks,
    Rafael
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  5. Re: [bug] 2.6.27-rc1: I/O errors after resume

    On Thu, 31 Jul 2008, Rafael J. Wysocki wrote:
    > On Thursday, 31 of July 2008, Miklos Szeredi wrote:
    > > With 2.6.27-rc1 things break badly after resume on my T60. Dmesg and
    > > config attached. 2.6.26 worked fine.

    >
    > Ugh, lots of stuff in a single message.


    Yeah, sorry. Search for "I/O error" for the interesting parts.

    > Anyway, can you try the current -git and report back, please? It's possible
    > that this has been fixed already.


    Not fixed:

    mszeredi@tucsk:~> uname -a
    Linux tucsk 2.6.27-rc1-00156-g94ad374 #17 SMP Thu Jul 31 15:45:10 CEST 2008 x86_64 x86_64 x86_64 GNU/Linux
    mszeredi@tucsk:~> dmesg
    bash: /bin/dmesg: Input/output error

    Seems easily reproducible, so if no better ideas I can try to bisect
    it.

    Miklos
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  6. Re: [bug] 2.6.27-rc1: I/O errors after resume

    On Thursday, 31 of July 2008, Miklos Szeredi wrote:
    > On Thu, 31 Jul 2008, Rafael J. Wysocki wrote:
    > > On Thursday, 31 of July 2008, Miklos Szeredi wrote:
    > > > With 2.6.27-rc1 things break badly after resume on my T60. Dmesg and
    > > > config attached. 2.6.26 worked fine.

    > >
    > > Ugh, lots of stuff in a single message.

    >
    > Yeah, sorry. Search for "I/O error" for the interesting parts.
    >
    > > Anyway, can you try the current -git and report back, please? It's possible
    > > that this has been fixed already.

    >
    > Not fixed:
    >
    > mszeredi@tucsk:~> uname -a
    > Linux tucsk 2.6.27-rc1-00156-g94ad374 #17 SMP Thu Jul 31 15:45:10 CEST 2008 x86_64 x86_64 x86_64 GNU/Linux
    > mszeredi@tucsk:~> dmesg
    > bash: /bin/dmesg: Input/output error
    >
    > Seems easily reproducible, so if no better ideas I can try to bisect it.


    That would be really helpful.

    Thanks,
    Rafael
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

  7. Re: [bug] 2.6.27-rc1: I/O errors after resume

    On Thursday, 31 of July 2008, Rafael J. Wysocki wrote:
    > On Thursday, 31 of July 2008, Miklos Szeredi wrote:
    > > On Thu, 31 Jul 2008, Rafael J. Wysocki wrote:
    > > > On Thursday, 31 of July 2008, Miklos Szeredi wrote:
    > > > > With 2.6.27-rc1 things break badly after resume on my T60. Dmesg and
    > > > > config attached. 2.6.26 worked fine.
    > > >
    > > > Ugh, lots of stuff in a single message.

    > >
    > > Yeah, sorry. Search for "I/O error" for the interesting parts.
    > >
    > > > Anyway, can you try the current -git and report back, please? It's possible
    > > > that this has been fixed already.

    > >
    > > Not fixed:
    > >
    > > mszeredi@tucsk:~> uname -a
    > > Linux tucsk 2.6.27-rc1-00156-g94ad374 #17 SMP Thu Jul 31 15:45:10 CEST 2008 x86_64 x86_64 x86_64 GNU/Linux
    > > mszeredi@tucsk:~> dmesg
    > > bash: /bin/dmesg: Input/output error
    > >
    > > Seems easily reproducible, so if no better ideas I can try to bisect it.

    >
    > That would be really helpful.


    Please also have a look at http://bugzilla.kernel.org/show_bug.cgi?id=11178

    Thanks,
    Rafael
    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

+ Reply to Thread