There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz
---
drivers/ide/pci/aec62xx.c | 2 +-
drivers/ide/pci/alim15x3.c | 5 ++---
drivers/ide/pci/amd74xx.c | 19 ++++++++-----------
drivers/ide/pci/cmd64x.c | 2 +-
drivers/ide/pci/cs5530.c | 7 +++----
drivers/ide/pci/cy82c693.c | 10 +++++-----
drivers/ide/pci/hpt34x.c | 2 +-
drivers/ide/pci/hpt366.c | 3 ++-
drivers/ide/pci/it821x.c | 2 +-
drivers/ide/pci/pdc202xx_new.c | 3 ++-
drivers/ide/pci/pdc202xx_old.c | 3 +--
drivers/ide/pci/piix.c | 3 +--
drivers/ide/pci/serverworks.c | 6 +++---
drivers/ide/pci/siimage.c | 8 +++-----
drivers/ide/pci/sis5513.c | 3 +--
drivers/ide/pci/sl82c105.c | 2 +-
drivers/ide/pci/via82cxxx.c | 3 +--
drivers/ide/setup-pci.c | 2 +-
include/linux/ide.h | 2 +-
19 files changed, 39 insertions(+), 48 deletions(-)

Index: b/drivers/ide/pci/aec62xx.c
================================================== =================
--- a/drivers/ide/pci/aec62xx.c
+++ b/drivers/ide/pci/aec62xx.c
@@ -140,7 +140,7 @@ static void aec_set_pio_mode(ide_drive_t
drive->hwif->port_ops->set_dma_mode(drive, pio + XFER_PIO_0);
}

-static unsigned int __devinit init_chipset_aec62xx(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_aec62xx(struct pci_dev *dev)
{
/* These are necessary to get AEC6280 Macintosh cards to work */
if ((dev->device == PCI_DEVICE_ID_ARTOP_ATP865) ||
Index: b/drivers/ide/pci/alim15x3.c
================================================== =================
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -209,13 +209,12 @@ static int ali15x3_dma_setup(ide_drive_t
/**
* init_chipset_ali15x3 - Initialise an ALi IDE controller
* @dev: PCI device
- * @name: Name of the controller
*
* This function initializes the ALI IDE controller and where
* appropriate also sets up the 1533 southbridge.
*/
-
-static unsigned int __devinit init_chipset_ali15x3 (struct pci_dev *dev, const char *name)
+
+static unsigned int __devinit init_chipset_ali15x3(struct pci_dev *dev)
{
unsigned long flags;
u8 tmpbyte;
Index: b/drivers/ide/pci/amd74xx.c
================================================== =================
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -112,15 +112,13 @@ static void amd_set_pio_mode(ide_drive_t
amd_set_drive(drive, XFER_PIO_0 + pio);
}

-static void __devinit amd7409_cable_detect(struct pci_dev *dev,
- const char *name)
+static void __devinit amd7409_cable_detect(struct pci_dev *dev)
{
/* no host side cable detection */
amd_80w = 0x03;
}

-static void __devinit amd7411_cable_detect(struct pci_dev *dev,
- const char *name)
+static void __devinit amd7411_cable_detect(struct pci_dev *dev)
{
int i;
u32 u = 0;
@@ -131,9 +129,9 @@ static void __devinit amd7411_cable_dete
amd_80w = ((t & 0x3) ? 1 : 0) | ((t & 0xc) ? 2 : 0);
for (i = 24; i >= 0; i -= 8)
if (((u >> i) & 4) && !(amd_80w & (1 << (1 - (i >> 4))))) {
- printk(KERN_WARNING "%s %s: BIOS didn't set cable bits "
- "correctly. Enabling workaround.\n",
- name, pci_name(dev));
+ printk(KERN_WARNING DRV_NAME " %s: BIOS didn't set "
+ "cable bits correctly. Enabling workaround.\n",
+ pci_name(dev));
amd_80w |= (1 << (1 - (i >> 4)));
}
}
@@ -142,8 +140,7 @@ static void __devinit amd7411_cable_dete
* The initialization callback. Initialize drive independent registers.
*/

-static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev,
- const char *name)
+static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev)
{
u8 t = 0, offset = amd_offset(dev);

@@ -156,9 +153,9 @@ static unsigned int __devinit init_chips
; /* no UDMA > 2 */
else if (dev->vendor == PCI_VENDOR_ID_AMD &&
dev->device == PCI_DEVICE_ID_AMD_VIPER_7409)
- amd7409_cable_detect(dev, name);
+ amd7409_cable_detect(dev);
else
- amd7411_cable_detect(dev, name);
+ amd7411_cable_detect(dev);

/*
* Take care of prefetch & postwrite.
Index: b/drivers/ide/pci/cmd64x.c
================================================== =================
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -332,7 +332,7 @@ static int cmd646_1_dma_end(ide_drive_t
return (dma_stat & 7) != 4;
}

-static unsigned int __devinit init_chipset_cmd64x(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_cmd64x(struct pci_dev *dev)
{
u8 mrdmode = 0;

Index: b/drivers/ide/pci/cs5530.c
================================================== =================
--- a/drivers/ide/pci/cs5530.c
+++ b/drivers/ide/pci/cs5530.c
@@ -129,12 +129,11 @@ static void cs5530_set_dma_mode(ide_driv
/**
* init_chipset_5530 - set up 5530 bridge
* @dev: PCI device
- * @name: device name
*
* Initialize the cs5530 bridge for reliable IDE DMA operation.
*/

-static unsigned int __devinit init_chipset_cs5530 (struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_cs5530(struct pci_dev *dev)
{
struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;

@@ -153,11 +152,11 @@ static unsigned int __devinit init_chips
}
}
if (!master_0) {
- printk(KERN_ERR "%s: unable to locate PCI MASTER function\n", name);
+ printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n");
goto out;
}
if (!cs5530_0) {
- printk(KERN_ERR "%s: unable to locate CS5530 LEGACY function\n", name);
+ printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n");
goto out;
}

Index: b/drivers/ide/pci/cy82c693.c
================================================== =================
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -332,7 +332,7 @@ static void cy82c693_set_pio_mode(ide_dr
/*
* this function is called during init and is used to setup the cy82c693 chip
*/
-static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev)
{
if (PCI_FUNC(dev->devfn) != 1)
return 0;
@@ -351,8 +351,8 @@ static unsigned int __devinit init_chips
data = inb(CY82_DATA_PORT);

#if CY82C693_DEBUG_INFO
- printk(KERN_INFO "%s: Peripheral Configuration Register: 0x%X\n",
- name, data);
+ printk(KERN_INFO DRV_NAME ": Peripheral Configuration Register: 0x%X\n",
+ data);
#endif /* CY82C693_DEBUG_INFO */

/*
@@ -373,8 +373,8 @@ static unsigned int __devinit init_chips
outb(data, CY82_DATA_PORT);

#if CY82C693_DEBUG_INFO
- printk(KERN_INFO "%s: New Peripheral Configuration Register: 0x%X\n",
- name, data);
+ printk(KERN_INFO ": New Peripheral Configuration Register: 0x%X\n",
+ data);
#endif /* CY82C693_DEBUG_INFO */

#endif /* CY82C693_SETDMA_CLOCK */
Index: b/drivers/ide/pci/hpt34x.c
================================================== =================
--- a/drivers/ide/pci/hpt34x.c
+++ b/drivers/ide/pci/hpt34x.c
@@ -79,7 +79,7 @@ static void hpt34x_set_pio_mode(ide_driv
*/
#define HPT34X_PCI_INIT_REG 0x80

-static unsigned int __devinit init_chipset_hpt34x(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_hpt34x(struct pci_dev *dev)
{
int i = 0;
unsigned long hpt34xIoBase = pci_resource_start(dev, 4);
Index: b/drivers/ide/pci/hpt366.c
================================================== =================
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -970,11 +970,12 @@ static int __devinit hpt37x_calibrate_dp
return 1;
}

-static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev)
{
unsigned long io_base = pci_resource_start(dev, 4);
struct ide_host *host = pci_get_drvdata(dev);
struct hpt_info *info = host->host_priv + (&dev->dev == host->dev[1]);
+ const char *name = DRV_NAME;
u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */
u8 chip_type;
enum ata_clock clock;
Index: b/drivers/ide/pci/it821x.c
================================================== =================
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -599,7 +599,7 @@ static void __devinit it8212_disable_rai
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}

-static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev)
{
u8 conf;
static char *mode[2] = { "pass through", "smart" };
Index: b/drivers/ide/pci/pdc202xx_new.c
================================================== =================
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -326,8 +326,9 @@ static void __devinit apple_kiwi_init(st
}
#endif /* CONFIG_PPC_PMAC */

-static unsigned int __devinit init_chipset_pdcnew(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_pdcnew(struct pci_dev *dev)
{
+ const char *name = DRV_NAME;
unsigned long dma_base = pci_resource_start(dev, 4);
unsigned long sec_dma_base = dma_base + 0x08;
long pll_input, pll_output, ratio;
Index: b/drivers/ide/pci/pdc202xx_old.c
================================================== =================
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -265,8 +265,7 @@ static void pdc202xx_dma_timeout(ide_dri
ide_dma_timeout(drive);
}

-static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev,
- const char *name)
+static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev)
{
unsigned long dmabase = pci_resource_start(dev, 4);
u8 udma_speed_flag = 0, primary_mode = 0, secondary_mode = 0;
Index: b/drivers/ide/pci/piix.c
================================================== =================
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -200,13 +200,12 @@ static void piix_set_dma_mode(ide_drive_
/**
* init_chipset_ich - set up the ICH chipset
* @dev: PCI device to set up
- * @name: Name of the device
*
* Initialize the PCI device as required. For the ICH this turns
* out to be nice and simple.
*/

-static unsigned int __devinit init_chipset_ich(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_ich(struct pci_dev *dev)
{
u32 extra = 0;

Index: b/drivers/ide/pci/serverworks.c
================================================== =================
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -174,7 +174,7 @@ static void svwks_set_dma_mode(ide_drive
pci_write_config_byte(dev, 0x54, ultra_enable);
}

-static unsigned int __devinit init_chipset_svwks (struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_svwks(struct pci_dev *dev)
{
unsigned int reg;
u8 btr;
@@ -190,8 +190,8 @@ static unsigned int __devinit init_chips
pci_read_config_dword(isa_dev, 0x64, &reg);
reg &= ~0x00002000; /* disable 600ns interrupt mask */
if(!(reg & 0x00004000))
- printk(KERN_DEBUG "%s %s: UDMA not BIOS "
- "enabled.\n", name, pci_name(dev));
+ printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
+ "enabled.\n", pci_name(dev));
reg |= 0x00004000; /* enable UDMA/33 support */
pci_write_config_dword(isa_dev, 0x64, reg);
}
Index: b/drivers/ide/pci/siimage.c
================================================== =================
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -457,14 +457,12 @@ static void sil_sata_pre_reset(ide_drive
/**
* init_chipset_siimage - set up an SI device
* @dev: PCI device
- * @name: device name
*
* Perform the initial PCI set up for this device. Attempt to switch
* to 133 MHz clocking if the system isn't already set up to do it.
*/

-static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev,
- const char *name)
+static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
void __iomem *ioaddr = host->host_priv;
@@ -541,8 +539,8 @@ static unsigned int __devinit init_chips
{ "== 100", "== 133", "== 2X PCI", "DISABLED!" };

tmp >>= 4;
- printk(KERN_INFO "%s %s: BASE CLOCK %s\n",
- name, pci_name(dev), clk_str[tmp & 3]);
+ printk(KERN_INFO DRV_NAME " %s: BASE CLOCK %s\n",
+ pci_name(dev), clk_str[tmp & 3]);
}

return 0;
Index: b/drivers/ide/pci/sis5513.c
================================================== =================
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -448,8 +448,7 @@ static int __devinit sis_find_family(str
return chipset_family;
}

-static unsigned int __devinit init_chipset_sis5513(struct pci_dev *dev,
- const char *name)
+static unsigned int __devinit init_chipset_sis5513(struct pci_dev *dev)
{
/* Make general config ops here
1/ tell IDE channels to operate in Compatibility mode only
Index: b/drivers/ide/pci/sl82c105.c
================================================== =================
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -272,7 +272,7 @@ static u8 sl82c105_bridge_revision(struc
* channel 0 here at least, but channel 1 has to be enabled by
* firmware or arch code. We still set both to 16 bits mode.
*/
-static unsigned int __devinit init_chipset_sl82c105(struct pci_dev *dev, const char *msg)
+static unsigned int __devinit init_chipset_sl82c105(struct pci_dev *dev)
{
u32 val;

Index: b/drivers/ide/pci/via82cxxx.c
================================================== =================
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -262,13 +262,12 @@ static void __devinit via_cable_detect(s
/**
* init_chipset_via82cxxx - initialization handler
* @dev: PCI device
- * @name: Name of interface
*
* The initialization callback. Here we determine the IDE chip type
* and initialize its drive independent registers.
*/

-static unsigned int __devinit init_chipset_via82cxxx(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_via82cxxx(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
struct via82cxxx_dev *vdev = host->host_priv;
Index: b/drivers/ide/setup-pci.c
================================================== =================
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -515,7 +515,7 @@ static int do_ide_setup_pci_device(struc
* space, place chipset into init-mode, and/or preserve
* an interrupt if the card is not native ide support.
*/
- ret = d->init_chipset ? d->init_chipset(dev, d->name) : 0;
+ ret = d->init_chipset ? d->init_chipset(dev) : 0;
if (ret < 0)
goto out;

Index: b/include/linux/ide.h
================================================== =================
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -1206,7 +1206,7 @@ enum {

struct ide_port_info {
char *name;
- unsigned int (*init_chipset)(struct pci_dev *, const char *);
+ unsigned int (*init_chipset)(struct pci_dev *);
void (*init_iops)(ide_hwif_t *);
void (*init_hwif)(ide_hwif_t *);
int (*init_dma)(ide_hwif_t *,
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/