This is a discussion on Re: Disk Shuffle - Hewlett Packard ; Scott, I hear you, but the combined total of the MPEXL_SYSTEM_VOLUME_SET is going to be 11 Gb ! Only the boot files MUST be on LDEV=1. According to the MPE 6.5 install manual: LDEV 1 requires a minimum capacity of ...
I hear you, but the combined total of the MPEXL_SYSTEM_VOLUME_SET is going to be 11 Gb ! Only the boot files MUST be on LDEV=1. According to the MPE 6.5 install manual:
LDEV 1 requires a minimum capacity of 500 MBytes. As of Release 5.0, you cannot use the
older HP7933 or HP7935 disk drives as LDEV 1 (the system disk).
AND later in the preparation instructions
:BUILD AXLDEV1.PUB.SYS;DISC=120000,1,1;DEV=1 (or 30,720,000 bytes)
:BUILD AXLSPACE.PUB.SYS;DISC=787000,32,32 (or 201,472,000 bytes)
for a grand total of 232,192,000 bytes.
in another section of the same manual, peak disk space sectors required for SLT, FOS, and full SUBSYS are 4,111,000 (or 1,052,416,000 bytes), not all of which needs to be on LDEV 1, but will all fit on LDEV 1
Also, I have an even older system with only 1 disk drive, which is 1.8 Gb, and it has 1/2 of this as free space with full 6.0 plus all patches.
-------------- Original message --------------
From: "Scott Baldwin"
> 2GB may be too little for ldev1, try and procure a 4gb disk.
> Scott Baldwin
> Orchard Consulting Group, LLC
> (856) 223-0565 (v)
> -----Original Message-----
> From: HP-3000 Systems Discussion [mailto:HP3000-L@RAVEN.UTC.EDU] On Behalf
> Of Wyell Grunwald
> Sent: Friday, April 18, 2008 12:21 PM
> To: HP3000-L@RAVEN.UTC.EDU
> Subject: [HP3000-L] Disk Shuffle
> Disk Shuffle - sounds like some sort of Adager command !
> I have a HP 3000 928RX that has 6.5 on it with the following disk
> 9 Gb internal drive - LDEV 1 (only 4 Gb recognized) MPEXL_SYSTEM_VOLUME_SET
> 9 Gb internal drive - LDEV 2 (all 9 Gb recognized) MPEXL_SYSTEM_VOLUME_SET
> 1.9 Gb external drive - LDEV 523 EXTRA_EXTERNAL_VOLUME_SET
> 1.9 Gb external drive - LDEV 524 EXTRA_EXTERNAL_VOLUME_SET
> I would like to go through the nasty process of switching the LDEV 1 drive
> with the LDEV 523 drive, so that I have use of the 4 Gb of space that is
> unrecognized (no, I cannot go to MPE 7.5). All drives are SCSI connected.
> Does this sound like I could do this ? Below is a sketching of the steps to
> do this - did I leave anything out ?
> 1) Make sure that all the essential files can fit on 1.9 Gb (which I think
> they will according the the OS installation manual)
> 2) Run BULDACCT @
> 3) Stop all jobs, background processes, network, etc.
> 4) STORE @.@.@;*T;DIRECTORY;SHOW to 2 separate tapes
> 5) Purge all ACCOUNTS on EXTRA_EXTERNAL_VOLUME_SET
> 6) VSCLOSE EXTRA_EXTERNAL_VOLUME_SET
> 7) VOLUTIL, SCRATCHVOL both disks in EXTRA_EXTERNAL_VOLUME_SET
> 8) SYSGEN, IO, DDEV 523, DDEV 524, HO, E, KE, TAPE (make 2 SLT tapes), E
> 9) ctrl-A SHUTDOWN, power off
> 10) physically swap the LDEV 523 disk with the LDEV 1 disk
> 11) swap the SCSI addresses on the disks in step 10 above ?
> 12) disconnect SCSI cable for external drives
> 13) boot the box from SLT tape created above in step 8
> 14) INSTALL
> 15) Reboot box from new LDEV 1 (primary path)
> 16) ISL> START NORECOVERY NOSYSSTART CONFIG=CONFG9X8 (This is so that it
> will not remember the old disk configuration)
> 17) ctrl-A, SHUTDOWN
> 18) re-attach SCSI cable for external drives
> 19) Reboot box from primary path
> 20) ISL> START NORECOVERY NOSYSTART
> 21) SYSGEN, IO, add all paths, devices back in, HO, E, KE, E
> 22) ctrl-A, SHUTDOWN
> 23) Reboot box from primary path
> 24) ISL> START NORECOVERY NOSYSSTART
> 25) VOLUTIL, NEWSET command to re-create EXTRA_EXTERNAL_VOLUME_SET
> 26) SHUTDOWN / Reboot neccessary ?
> 27) From store tape created in step 4 above, RESTORE
> 28) OPENQ LP, STREAMS 10, Stream BULDJOB1.PUB (To re-create all accounts,
> users, groups)
> 29) From store tape created in step 4 above, RESTORE
> 30) STREAM BULDJOB2.PUB (To re-create all udc's)
> 31) SHUTDOWN / Reboot WITH SYSSTART
> What a monumental task. Please comment if I left something out !
> Wyell Grunwald
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *