PCMCI won't be recognize - Hardware

This is a discussion on PCMCI won't be recognize - Hardware ; I try to follow the instructions from: http://www.pharscape.org/content/view/28/ Instructions for Vodafone card with CL serial number. for linux:~ # cardctl status I got: Socket 0: 3.3V CardBus card function 0: [ready] Socket 1: no card linux:~ # cardctl config Socket ...

+ Reply to Thread
Results 1 to 3 of 3

Thread: PCMCI won't be recognize

  1. PCMCI won't be recognize

    I try to follow the instructions from:
    http://www.pharscape.org/content/view/28/
    Instructions for Vodafone card with CL serial number.

    for
    linux:~ # cardctl status

    I got:

    Socket 0:
    3.3V CardBus card
    function 0: [ready]
    Socket 1:
    no card

    linux:~ # cardctl config
    Socket 0:
    Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
    interface type is "cardbus"
    irq 11 [exclusive] [level]
    function 0:
    Socket 1:
    not configured

    but for:

    cat /proc/bus/usb/devices



    I don't get Option. Only the mouse, OHCI and UHCI host controller are in
    usbview.


    p.s.

    I tried before:
    modprobe usbserial
    and
    modprobe serial_cs

    Somewhere else I found that I need to add "pci=assign-busses" to kernel
    parameters on bootup
    I don't know where I need to put that line and does that line will help me ?
    What other can be missing?

    Please help.






  2. Re: PCMCI won't be recognize

    To simplified my question:
    1. Does I need to see my PCMCIA card in a usbview
    2. If yes, How ?



  3. Re: PCMCI won't be recognize


    "Bill Marcum" je napisao u poruci interesnoj
    grupi:utp2k4-dt4.ln1@don.localnet...
    > On Tue, 12 Jun 2007 13:48:25 +0200, FreeStyler
    > wrote:
    > >
    > >
    > > To simplified my question:
    > > 1. Does I need to see my PCMCIA card in a usbview
    > > 2. If yes, How ?
    > >
    > >

    > Do you see it in lspci or cardctl ident?
    >
    >



    In lspci, No, I don't see anything like that.
    root@1[knoppix]# lspci
    0000:00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev a4)
    0000:00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6)
    0000:00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4)
    0000:00:02.0 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
    0000:00:02.1 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
    0000:00:02.2 USB Controller: nVidia Corporation nForce3 USB 2.0 (rev a2)
    0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce3 Audio
    (rev
    a2)
    0000:00:06.1 Modem: nVidia Corporation: Unknown device 00d9 (rev a2)
    0000:00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5)
    0000:00:0a.0 PCI bridge: nVidia Corporation nForce3 PCI Bridge (rev a2)
    0000:00:0b.0 PCI bridge: nVidia Corporation nForce3 AGP Bridge (rev a4)
    0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
    HyperTransport Technology Configuration
    0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
    Address Map
    0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
    DRAM Controller
    0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
    Miscellaneous Control
    0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4
    420 Go32M] (rev a3)
    0000:02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
    IEEE-1394a-2000 Controller (PHY/Link)
    0000:02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
    RTL-8139/8139C/8139C+ (rev 10)
    0000:02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g
    WirelessLAN Controller (rev 03)
    0000:02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
    (rev 01)
    0000:02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
    (rev 01)
    0000:02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
    Function (rev 01)

    For

    linux:~ # cardctl status

    I got:

    Socket 0:
    3.3V CardBus card
    function 0: [ready]
    Socket 1:
    no card

    linux:~ # cardctl config
    Socket 0:
    Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
    interface type is "cardbus"
    irq 11 [exclusive] [level]
    function 0:
    Socket 1:
    not configured

    If you look in a http://www.pharscape.org/content/view/28/#_Toc83808163
    2.1.1 PCMCIA
    that is supposed to be but next chapter is not passed for me, when I need to
    find the vendor ID.



+ Reply to Thread