Does anyone have a board with this chipset where ichwd attaches properly ?

When I try to load the driver I get

ichwd module loaded
isab0: found ICH9 or equivalent chipset: Intel ICH9R watchdog timer
ichwd0: on isa0
isab0: found ICH9 or equivalent chipset: Intel ICH9R watchdog timer
ichwd0: ICH WDT present but disabled in BIOS or hardware
device_attach: ichwd0 attach returned 6
ppc0: parallel port not found.

the ppc0 error seems normal, as on other boards I see the same error
and things attach just fine

It is enabled in the BIOS as the box will automatically reboot after
5 min, since the watchdog is not set by the OS

The machine is a supermicro S3200SHX chipset. wd settings in the BIOS
below. If I set the boot watchdog to disabled, it still does not attach

| Assert NMI on SERR [Enabled]
| Assert NMI on PERR [Enabled]
| Resume on AC Power Lo [Reset]
| Clear System Event Lo [Disabled]
| FRB-2 Enable [Enabled]
| OS Boot Watchdog Time [Enabled]
| OS Boot Watchdog Time [Reset]
| OS Boot Watchdog Time [5 minutes]

isab0@pci0:0:31:0: class=0x060100 card=0x34d08086
chip=0x29168086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IR (ICH9R) LPC Interface Controller'
class = bridge
subclass = PCI-ISA
cap 09[e0] = vendor (length 12) Intel cap 1 version 0
features: SATA RAID-5, 4 PCI-e x1 slots

Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-PRERELEASE #2: Tue Sep 30 21:07:11 EDT 2008
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU E6750 @ 2.66GHz (2707.88-MHz
686-class CPU)
Origin = "GenuineIntel" Id = 0x6fb Stepping = 11
AMD Features=0x20100000
AMD Features2=0x1
Cores per package: 2
real memory = 3755974656 (3581 MB)
avail memory = 3675566080 (3505 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 5
ioapic0 irqs 0-23 on motherboard
ioapic1 irqs 30-53 on motherboard
lapic0: Forcing LINT1 to edge trigger
kbd1 at kbdmux0
acpi0: on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_hpet0: iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
acpi_button0: on acpi0
acpi_button1: on acpi0
pcib0: port 0xcf8-0xcff on acpi0
pci0: on pcib0
pcib1: irq 16 at device 6.0 on pci0
pci1: on pcib1
3ware device driver for 9000 series storage controllers, version:
twa0: <3ware 9000 series Storage Controller> port 0x2000-0x20ff mem
0xe0000000-0xe1ffffff,0xe3a00000-0xe3a00fff irq 16 at device 0.0 on pci1
twa0: [ITHREAD]
twa0: INFO: (0x15: 0x1300): Controller details:: Model 9650SE-2LP, 2
ports, Firmware FE9X, BIOS BE9X
em0: port 0x30e0-0x30ff
mem 0xe3b00000-0xe3b1ffff,0xe3b20000-0xe3b20fff irq 20 at device 25.0 on pci0
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:15:17:28:d0:fe
uhci0: port 0x30c0-0x30df irq 18 at
device 26.0 on pci0
uhci0: [ITHREAD]
usb0: on uhci0
usb0: USB revision 1.0
uhub0: on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: port 0x30a0-0x30bf irq 21 at
device 26.1 on pci0
uhci1: [ITHREAD]
usb1: on uhci1
usb1: USB revision 1.0
uhub1: on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: port 0x3080-0x309f irq 17 at
device 26.2 on pci0
uhci2: [ITHREAD]
usb2: on uhci2
usb2: USB revision 1.0
uhub2: on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: mem 0xe3b21400-0xe3b217ff
irq 17 at device 26.7 on pci0
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: on ehci0
usb3: USB revision 2.0
uhub3: on usb3
uhub3: 6 ports with 6 removable, self powered
pcib2: irq 17 at device 28.0 on pci0
pci2: on pcib2
pcib3: at device 0.0 on pci2
pci3: on pcib3
pcib4: irq 17 at device 28.4 on pci0
pci4: on pcib4
vgapci0: mem
0xe2000000-0xe2ffffff,0xe3800000-0xe3803fff,0xe3000000-0xe37fffff irq
16 at device 0.0 on pci4
uhci3: port 0x3060-0x307f irq 23 at
device 29.0 on pci0
uhci3: [ITHREAD]
usb4: on uhci3
usb4: USB revision 1.0
uhub4: on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: port 0x3040-0x305f irq 19 at
device 29.1 on pci0
uhci4: [ITHREAD]
usb5: on uhci4
usb5: USB revision 1.0
uhub5: on usb5
uhub5: 2 ports with 2 removable, self powered
uhci5: port 0x3020-0x303f irq 18 at
device 29.2 on pci0
uhci5: [ITHREAD]
usb6: on uhci5
usb6: USB revision 1.0
uhub6: on usb6
uhub6: 2 ports with 2 removable, self powered
ehci1: mem 0xe3b21000-0xe3b213ff
irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usb7: EHCI version 1.0
usb7: companion controllers, 2 ports each: usb4 usb5 usb6
usb7: on ehci1
usb7: USB revision 2.0
uhub7: on usb7
uhub7: 6 ports with 6 removable, self powered
pcib5: at device 30.0 on pci0
pci5: on pcib5
em1: port 0x1000-0x103f
mem 0xe3920000-0xe393ffff,0xe3900000-0xe391ffff irq 18 at device 2.0 on pci5
em1: [FILTER]
em1: Ethernet address: 00:15:17:28:d0:fc
isab0: at device 31.0 on pci0
isa0: on isab0
atapci0: port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3430-0x343f,0x3420-0x342f irq
21 at device 31.2 on pci0
ata0: on atapci0
ata0: [ITHREAD]
ata1: on atapci0
ata1: [ITHREAD]
pci0: at device 31.3 (no driver attached)
atapci1: port
irq 21 at device 31.5 on pci0
atapci1: [ITHREAD]
ata2: on atapci1
ata2: [ITHREAD]
ata3: on atapci1
ata3: [ITHREAD]
atkbdc0: port 0x60,0x64 irq 1 on acpi0
atkbd0: irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
cpu0: on acpi0
est0: on cpu0
p4tcc0: on cpu0
cpu1: on acpi0
est1: on cpu1
p4tcc1: on cpu1
cryptosoft0: on motherboard
pmtimer0 on isa0
orm0: at iomem 0xc0000-0xc7fff,0xc8000-0xc9fff
pnpid ORM0000 on isa0
sc0: at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: parallel port not found.
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
da0 at twa0 bus 0 target 0 lun 0
da0: Fixed Direct Access SCSI-5 device
da0: 100.000MB/s transfers
da0: 238408MB (488259584 512 byte sectors: 255H 63S/T 30392C)
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/da0s1a


Mike Tancsa, tel +1 519 651 3400
Sentex Communications,
Providing Internet since 1994
Cambridge, Ontario Canada

_______________________________________________ mailing list
To unsubscribe, send any mail to ""