This is a discussion on Re: Any successful installs on a Broadcom HT1000 chipset? - FreeBSD ; There aren't many SATA options, INT13 on or off (can't boot from it without that on..) and then S-ATA, P-ATA or RAID modes. S-ATA and P-ATA (another way of saying legacy on/off) modes both crash and burn the same, corrupting ...
There aren't many SATA options, INT13 on or off (can't boot from it
without that on..) and then S-ATA, P-ATA or RAID modes.
S-ATA and P-ATA (another way of saying legacy on/off) modes both crash
and burn the same, corrupting most data on the disk that the controller
It's too bad, the SiI3114 32-bit PCI SATA controller is considerably
slower, but at least it works reliably.
I tend to agree with what Anton Yuzhaninov said on 11/9, this seems like
it could be a PCI-X problem with the ServerWorks HT1000/HT2000 chipset
(and other chipsets) and FreeBSD.
Mike Tancsa wrote:
> At 10:11 PM 11/13/2007, Travis Mikalson wrote:
>> There is definitely a problem. The Tyan S3950G2NR (HT1000) on-board
>> SATA controller corrupts my data horribly and so does a Marvell
>> 88SX6081 8-port
> What are your SATA BIOS options set to ? I have such a board and I
> recall having to change the mode of the SATA controller for it to work.
> I think its turning off legacy mode. I also seem to recall having to
> fiddle with some USB options as well.
> I was running 6.1 and recently upgraded the box to RELENG_6 as of oct 25
> and the box continued to work fine.
> Copyright (c) 1992-2007 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 6.3-PRERELEASE #1: Thu Oct 25 21:54:13 EDT 2007
> ACPI APIC Table:
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: AMD Athlon(tm) 64 Processor 3800+ (2413.18-MHz 686-class CPU)
> Origin = "AuthenticAMD" Id = 0x40ff2 Stepping = 2
> AMD Features=0xea500800
> AMD Features2=0x1d
> real memory = 1073676288 (1023 MB)
> avail memory = 1041670144 (993 MB)
> MADT: Forcing active-low polarity and level trigger for SCI
irqs 0-15 on motherboard
irqs 16-31 on motherboard
irqs 32-47 on motherboard
> kbd1 at kbdmux0
> acpi0: on motherboard
> acpi0: Power Button (fixed)
> acpi0: Sleep Button (fixed)
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
port 0xcf8-0xcff on acpi0
at device 1.0 on pci0
at device 13.0 on pci1
> 0xa880-0xa8bf mem 0xff2c0000-0xff2dffff,0xff280000-0xff2bffff irq 16 at
> device 3.0 on pci2
> em0: Ethernet address: 00:0e:0c:81:14:d4
> 0xac00-0xac3f mem 0xff2e0000-0xff2fffff irq 17 at device 3.1 on pci2
> em1: Ethernet address: 00:0e:0c:81:14:d5
> mem 0xff3fe000-0xff3fffff irq 11 at device 14.0 on pci1
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 2.1 on pci0
at device 2.2 on pci0
port 0xe000-0xe0ff mem
> 0xff6b4000-0xff6b4fff irq 10 at device 3.0 on pci0
> ohci0: [GIANT-LOCKED]
> usb0: OHCI version 1.0, legacy support
> usb0: SMM does not respond, resetting
> usb0: USB revision 1.0
> uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
port 0xe400-0xe4ff mem
> 0xff6b5000-0xff6b5fff irq 10 at device 3.1 on pci0
> ohci1: [GIANT-LOCKED]
> usb1: OHCI version 1.0, legacy support
> usb1: SMM does not respond, resetting
> usb1: USB revision 1.0
> uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
port 0xe800-0xe8ff mem
> 0xff6b6000-0xff6b6fff irq 10 at device 3.2 on pci0
> ehci0: [GIANT-LOCKED]
> usb2: EHCI version 1.0
> usb2: companion controllers, 2 ports each: usb0 usb1
> usb2: USB revision 2.0
> uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub2: 4 ports with 4 removable, self powered
> 0xdc00-0xdc3f mem 0xff680000-0xff69ffff,0xff660000-0xff67ffff irq 24 at
> device 4.0 on pci0
> em2: Ethernet address: 00:e0:81:5e:be:3c
> 0xd880-0xd8bf mem 0xff620000-0xff63ffff,0xff600000-0xff61ffff irq 25 at
> device 5.0 on pci0
> em3: Ethernet address: 00:e0:81:5e:be:3d
at device 6.0 (no driver attached)
port 0xd400-0xd4ff mem
> 0xff6b3c00-0xff6b3cff irq 27 at device 7.0 on pci0
> rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl0: Ethernet address: 00:50:fc:a7:9d:04
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
> sio0: type 16550A, console
> pmtimer0 on isa0
> 0xc0000-0xc7fff,0xc8000-0xc9fff,0xca000-0xcafff,0xcb000-0xcbfff on isa0
at port 0x60,0x64 on isa0
irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> ppc0: parallel port not found.
at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounter "TSC" frequency 2413179713 Hz quality 800
> Timecounters tick every 1.000 msec
> ad4: 76319MB
at ata2-master SATA150
> Trying to mount root from ufs:/dev/ad4s1a
>> I have had to buy a couple cheap 4-port SiI3114 PCI cards for now to
>> be able to use this system with RELENG_7 and ZFS.
>> Jeff Roberson wrote:
>>> I have reports from a user that his install ends up corrupted. I
>>> wanted to find out if it was a general problem with this chipset.
>> TerraNovaNet Internet Services - Key Largo, FL
>> Voice: (305)453-4011 x101 Fax: (305)451-5991
>> Life's not fair, but the root password helps.
>> firstname.lastname@example.org mailing list
>> To unsubscribe, send any mail to
> email@example.com mailing list
> To unsubscribe, send any mail to "firstname.lastname@example.org"
TerraNovaNet Internet Services - Key Largo, FL
Voice: (305)453-4011 x101 Fax: (305)451-5991
Life's not fair, but the root password helps.
email@example.com mailing list
To unsubscribe, send any mail to "firstname.lastname@example.org"