At 10:11 PM 11/13/2007, Travis Mikalson wrote:
>There is definitely a problem. The Tyan S3950G2NR (HT1000) on-board
>SATA controller corrupts my data horribly and so does a Marvell
>88SX6081 8-port


What are your SATA BIOS options set to ? I have such a board and I
recall having to change the mode of the SATA controller for it to
work. I think its turning off legacy mode. I also seem to recall
having to fiddle with some USB options as well.

I was running 6.1 and recently upgraded the box to RELENG_6 as of oct
25 and the box continued to work fine.

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-PRERELEASE #1: Thu Oct 25 21:54:13 EDT 2007
mdtancsa@fw3.sentex.ca:/usr/obj/usr/src/sys/iolite
ACPI APIC Table:
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3800+ (2413.18-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x40ff2 Stepping = 2
Features=0x78bfbff
Features2=0x2001
AMD Features=0xea500800
AMD Features2=0x1d
real memory = 1073676288 (1023 MB)
avail memory = 1041670144 (993 MB)
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 irqs 0-15 on motherboard
ioapic1 irqs 16-31 on motherboard
ioapic2 irqs 32-47 on motherboard
kbd1 at kbdmux0
acpi0:
on motherboard
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
cpu0: on acpi0
pcib0: port 0xcf8-0xcff on acpi0
pci0: on pcib0
pcib1: at device 1.0 on pci0
pci1: on pcib1
pcib2: at device 13.0 on pci1
pci2: on pcib2
em0: port
0xa880-0xa8bf mem 0xff2c0000-0xff2dffff,0xff280000-0xff2bffff irq 16
at device 3.0 on pci2
em0: Ethernet address: 00:0e:0c:81:14:d4
em1: port
0xac00-0xac3f mem 0xff2e0000-0xff2fffff irq 17 at device 3.1 on pci2
em1: Ethernet address: 00:0e:0c:81:14:d5
atapci0: port
0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb81f
mem 0xff3fe000-0xff3fffff irq 11 at device 14.0 on pci1
ata2: on atapci0
ata3: on atapci0
ata4: on atapci0
ata5: on atapci0
atapci1: port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 2.1 on pci0
ata0: on atapci1
ata1: on atapci1
isab0: at device 2.2 on pci0
isa0: on isab0
ohci0: port 0xe000-0xe0ff mem
0xff6b4000-0xff6b4fff irq 10 at device 3.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ohci1: port 0xe400-0xe4ff mem
0xff6b5000-0xff6b5fff irq 10 at device 3.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: on ohci1
usb1: USB revision 1.0
uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0: port 0xe800-0xe8ff mem
0xff6b6000-0xff6b6fff irq 10 at device 3.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: on ehci0
usb2: USB revision 2.0
uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
em2: port
0xdc00-0xdc3f mem 0xff680000-0xff69ffff,0xff660000-0xff67ffff irq 24
at device 4.0 on pci0
em2: Ethernet address: 00:e0:81:5e:be:3c
em3: port
0xd880-0xd8bf mem 0xff620000-0xff63ffff,0xff600000-0xff61ffff irq 25
at device 5.0 on pci0
em3: Ethernet address: 00:e0:81:5e:be:3d
pci0: at device 6.0 (no driver attached)
rl0: port 0xd400-0xd4ff mem
0xff6b3c00-0xff6b3cff irq 27 at device 7.0 on pci0
miibus0: on rl0
rlphy0: on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:50:fc:a7:9d:04
acpi_button0: on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
pmtimer0 on isa0
orm0: at iomem
0xc0000-0xc7fff,0xc8000-0xc9fff,0xca000-0xcafff,0xcb000-0xcbfff on isa0
atkbdc0: at port 0x60,0x64 on isa0
atkbd0: irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
sc0: at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 2413179713 Hz quality 800
Timecounters tick every 1.000 msec
ad4: 76319MB at ata2-master SATA150
Trying to mount root from ufs:/dev/ad4s1a


>I have had to buy a couple cheap 4-port SiI3114 PCI cards for now to
>be able to use this system with RELENG_7 and ZFS.
>
>Jeff Roberson wrote:
>>I have reports from a user that his install ends up corrupted. I
>>wanted to find out if it was a general problem with this chipset.
>>Thanks,
>>Jeff

>
>--
>TerraNovaNet Internet Services - Key Largo, FL
>Voice: (305)453-4011 x101 Fax: (305)451-5991
>
http://www.terranova.net/
>----------------------------------------------
>Life's not fair, but the root password helps.
>_______________________________________________
>freebsd-current@freebsd.org mailing list
>http://lists.freebsd.org/mailman/lis...reebsd-current
>To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"


_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/lis...reebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"