Package: linux-image-2.6.26-1-686
Version: 2.6.26-5
Severity: normal


The current kernel for Lenny (2.6.26-1) boots fine on an Acer Aspire
One, except if there is an SDHC card in one of the card reader slots.

Then the boot process gets as far as:

Waiting for /dev to be fully populated

and hangs. After a minute the following message appears:

BUG: soft lockup - CPU#1 stuck for 61s! [kmemstick:1503]

and the message is repeated every minute after that.

The same configuration boots successfully with kernel 2.6.22 and the
memory card can be accessed once the boot is complete (although 2.6.22
doesn't support other aspects of the hardware).


-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-5) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Sep 10 16:46:13 UTC 2008

** Command line:
root=/dev/sda1 ro elevator=noop quiet

** Tainted: P (1)

** Kernel log:
[ 4.411602] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.455799] Driver 'sd' needs updating - please use bus_type methods
[ 4.455966] sd 1:0:0:0: [sda] 15761088 512-byte hardware sectors (8070 MB)
[ 4.456009] sd 1:0:0:0: [sda] Write Protect is off
[ 4.456015] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.456087] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.456222] sd 1:0:0:0: [sda] 15761088 512-byte hardware sectors (8070 MB)
[ 4.456262] sd 1:0:0:0: [sda] Write Protect is off
[ 4.456268] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.456341] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.456351] sda: sda1 sda2
[ 4.461826] sd 1:0:0:0: [sda] Attached SCSI disk
[ 4.567128] PM: Starting manual resume from disk
[ 4.949434] usb 5-5: new high speed USB device using ehci_hcd and address 3
[ 5.302032] usb 5-5: configuration #1 chosen from 1 choice
[ 5.348648] usb 5-5: New USB device found, idVendor=064e, idProduct=d101
[ 5.348648] usb 5-5: New USB device strings: Mfr=3, Product=1, SerialNumber=4
[ 5.348648] usb 5-5: Product: Acer Crystal Eye webcam
[ 5.348648] usb 5-5: Manufacturer: SuYin
[ 5.348648] usb 5-5: SerialNumber: CN0316-M608-OV01-VA-R02.00.00
[ 5.407072] udevd version 125 started
[ 5.587926] usb 1-1: new low speed USB device using uhci_hcd and address 4
[ 5.756507] usb 1-1: configuration #1 chosen from 1 choice
[ 5.760819] usb 1-1: New USB device found, idVendor=1267, idProduct=0210
[ 5.760819] usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 5.760819] usb 1-1: Product: PS/2+USB Mouse
[ 5.782903] Linux video capture interface: v2.00
[ 5.799282] uvcvideo: Found UVC 1.00 device Acer Crystal Eye webcam (064e:d101)
[ 5.803246] input: Acer Crystal Eye webcam as /class/input/input1
[ 5.803331] usbcore: registered new interface driver uvcvideo
[ 5.803341] USB Video Class driver (v0.1.0)
[ 6.176665] ACPI: WMI: Mapper loaded
[ 6.196669] acer-wmi: Acer Laptop ACPI-WMI Extras version 0.1
[ 7.506790] Linux agpgart interface v0.103
[ 7.526372] agpgart: Detected an Intel 945GME Chipset.
[ 7.526605] agpgart: Detected 7932K stolen memory.
[ 7.542793] agpgart: AGP aperture is 256M @ 0x20000000
[ 7.844087] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 7.844133] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 7.876856] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 8.168975] ath_hal: module license 'Proprietary' taints kernel.
[ 8.181538] AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417)
[ 8.545621] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 8.545646] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 9.035636] MadWifi: ath_attach: Switching rfkill capability off.
[ 9.091067] input: Power Button (FF) as /class/input/input2
[ 9.091344] ACPI: AC Adapter [ACAD] (off-line)
[ 9.135933] ACPI: Power Button (FF) [PWRF]
[ 9.136795] input: Power Button (CM) as /class/input/input3
[ 9.180203] ACPI: Power Button (CM) [PWRB]
[ 9.180382] input: Lid Switch as /class/input/input4
[ 9.239222] ACPI: Lid Switch [LID0]
[ 9.239424] input: Sleep Button (CM) as /class/input/input5
[ 9.267172] ACPI: Sleep Button (CM) [SLPB]
[ 10.090084] ACPI: Battery Slot [BAT1] (battery present)
[ 10.215969] input: Video Bus as /class/input/input6
[ 10.266579] ACPI: Video Device [OVGA] (multi-head: yes rom: yes post: no)
[ 10.390518] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 10.390684] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x0460)
[ 10.390742] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.967495] intel_rng: FWH not detected
[ 11.180260] input: PC Speaker as /class/input/input7
[ 11.393304] usbcore: registered new interface driver hiddev
[ 11.408223] input: PS/2+USB Mouse as /class/input/input8
[ 11.459638] input,hidraw0: USB HID v1.00 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.0-1
[ 11.459683] usbcore: registered new interface driver usbhid
[ 11.459693] usbhid: v2.6:USB HID core driver
[ 11.509137] Error: Driver 'pcspkr' is already registered, aborting...
[ 11.656385] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, Radio 10.2)
[ 11.944663] ath_pci: wifi0: Atheros 5424/2424: mem=0x35200000, irq=18
[ 11.945150] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 12.126662] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04771/0xa40000
[ 12.180195] input: SynPS/2 Synaptics TouchPad as /class/input/input9
[ 13.274035] Adding 554232k swap on /dev/sda2. Priority:-1 extents:1 across:554232k
[ 14.440976] loop: module loaded
[ 20.334272] r8169: eth0: link down
[ 22.654097] NET: Registered protocol family 10
[ 22.654097] lo: Disabled Privacy Extensions
[ 22.655148] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.892186] lp: driver loaded but no devices found
[ 23.085254] ppdev: user-space parallel port driver
[ 25.246371] device eth0 entered promiscuous mode
[ 25.979264] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 28.234213] Bluetooth: Core ver 2.11
[ 28.234213] NET: Registered protocol family 31
[ 28.234213] Bluetooth: HCI device and connection manager initialized
[ 28.234213] Bluetooth: HCI socket layer initialized
[ 28.350327] Bluetooth: L2CAP ver 2.9
[ 28.350327] Bluetooth: L2CAP socket layer initialized
[ 28.459056] Bluetooth: RFCOMM socket layer initialized
[ 28.459056] Bluetooth: RFCOMM TTY layer initialized
[ 28.459056] Bluetooth: RFCOMM ver 1.8
[ 31.602701] [drm] Initialized drm 1.1.0 20060810
[ 31.610670] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 31.610670] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 31.610670] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 31.774713] mtrr: no more MTRRs available
[ 89.749768] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 99.978588] ath0: no IPv6 routers present
[ 113.561007] ath0: no IPv6 routers present

** Loaded modules:
Module Size Used by
wlan_tkip 10272 2
i915 25280 2
drm 65256 3 i915
rfcomm 28272 0
l2cap 17248 5 rfcomm
bluetooth 44900 4 rfcomm,l2cap
ppdev 6468 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
ipv6 235300 24
acpi_cpufreq 6796 1
cpufreq_userspace 3172 0
cpufreq_stats 3776 0
cpufreq_powersave 1856 0
cpufreq_ondemand 6476 1
freq_table 4224 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 5960 0
loop 12748 0
joydev 8480 0
wlan_scan_sta 11200 1
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
psmouse 32336 0
snd_pcsp 8576 0
serio_raw 4740 0
rng_core 3940 0
i2c_i801 7920 0
i2c_core 19828 1 i2c_i801
iTCO_wdt 9508 0
video 16400 0
output 2912 1 video
ath_rate_sample 11008 1
battery 10180 0
button 6064 0
ac 4196 0
ath_pci 202104 0
wlan 193040 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci
ath_hal 300672 3 ath_rate_sample,ath_pci
snd_hda_intel 324248 1
intel_agp 22300 1
agpgart 28776 3 drm,intel_agp
snd_pcm_oss 32800 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62628 3 snd_pcsp,snd_hda_intel,snd_pcm_oss
snd_timer 17800 1 snd_pcm
snd 45604 8 snd_pcsp,snd_hda_intel,snd_pcm_oss,snd_mixer_oss,s nd_pcm,snd_timer
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
acer_wmi 8852 0
led_class 3908 1 acer_wmi
evdev 8000 8
wmi 6440 1 acer_wmi
uvcvideo 45576 0
compat_ioctl32 1312 1 uvcvideo
videodev 27520 1 uvcvideo
v4l1_compat 12260 2 uvcvideo,videodev
ext2 54344 1
mbcache 7108 1 ext2
sd_mod 22200 3
ide_pci_generic 3908 0 [permanent]
ide_core 92628 1 ide_pci_generic
ata_generic 4676 0
ata_piix 14180 2
libata 140416 2 ata_generic,ata_piix
scsi_mod 129356 2 sd_mod,libata
dock 8272 1 libata
ehci_hcd 28428 0
uhci_hcd 18672 0
usbcore 118160 5 usbhid,uvcvideo,ehci_hcd,uhci_hcd
r8169 23684 0
thermal 15228 0
processor 32576 4 acpi_cpufreq,thermal
fan 4164 0
thermal_sys 10856 4 video,thermal,processor,fan

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Capabilities:
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 38480000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 60c0 [size=8]
Region 2: Memory at 20000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at 38500000 (32-bit, non-prefetchable) [size=256K]
Capabilities:

00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Region 0: Memory at 38400000 (32-bit, non-prefetchable) [size=512K]
Capabilities:

00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 38540000 (64-bit, non-prefetchable) [size=16K]
Capabilities:
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: 37300000-383fffff
Prefetchable memory behind bridge: 0000000030000000-0000000030ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00004fff
Memory behind bridge: 36300000-372fffff
Prefetchable memory behind bridge: 0000000031000000-00000000320fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 35200000-362fffff
Prefetchable memory behind bridge: 0000000032100000-00000000330fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 34100000-351fffff
Prefetchable memory behind bridge: 0000000033100000-00000000340fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 6080 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 6060 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 6040 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 6020 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 38544400 (32-bit, non-prefetchable) [size=1K]
Capabilities:
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Capabilities:
Kernel modules: intel-rng, iTCO_wdt

00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 02) (prog-if 80 [Master])
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 60a0 [size=16]
Capabilities:
Kernel driver in use: ata_piix
Kernel modules: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 6000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:015b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 219
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at 31010000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at 31000000 (64-bit, prefetchable) [size=64K]
Expansion ROM at 31020000 [disabled] [size=128K]
Capabilities:
Kernel driver in use: r8169
Kernel modules: r8169

03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 35200000 (64-bit, non-prefetchable) [size=64K]
Capabilities:
Kernel driver in use: ath_pci
Kernel modules: ath5k, ath_pci



-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)

Kernel: Linux 2.6.26-1-686 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92j tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-13 GNU C Library: Shared libraries [i

Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 (no description available)

-- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:



--
To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org