Bug#497392: e1000e driver does not initialize correctly - Debian

This is a discussion on Bug#497392: e1000e driver does not initialize correctly - Debian ; Package: linux-image-2.6.26-1-686 Version: 2.6.26-3 Severity: important The e1000e kernel module does not initialize correctly, then the network cannot initialize. It does not complain, but packets do not exit correctly. The port's LED on switch blinks quickly all time, IPv6 RA's ...

+ Reply to Thread
Results 1 to 3 of 3

Thread: Bug#497392: e1000e driver does not initialize correctly

  1. Bug#497392: e1000e driver does not initialize correctly

    Package: linux-image-2.6.26-1-686
    Version: 2.6.26-3
    Severity: important

    The e1000e kernel module does not initialize correctly, then the network cannot initialize.
    It does not complain, but packets do not exit correctly. The port's LED on switch blinks quickly all time, IPv6 RA's are recevied by the kernel, but no DHCP packet reaches router, nor any ICMP one after manual configuration.
    rmmod / modprobe module *sometimes* makes it working correctly, then the network interface is bringed up, DHCP responds, and communication can be established.

    e1000e worked correctly with linux-image-2.6.25-2-686 kernel.

    -- Package-specific info:
    ** Version:
    Linux version 2.6.26-1-686 (Debian 2.6.26-3) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Aug 20 12:56:41 UTC 2008

    ** Command line:
    root=/dev/sda6 ro

    ** Not tainted

    ** Kernel log:
    [ 5.639460] EXT3-fs: mounted filesystem with ordered data mode.
    [ 6.838118] udevd version 125 started
    [ 7.555905] input: PC Speaker as /class/input/input3
    [ 8.116282] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 18 (level, low) -> IRQ 18
    [ 8.240908] Linux agpgart interface v0.103
    [ 8.280909] agpgart: Detected an Intel G33 Chipset.
    [ 8.280909] agpgart: Detected 7164K stolen memory.
    [ 8.294893] agpgart: AGP aperture is 256M @ 0xd0000000
    [ 8.297597] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
    [ 8.316909] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
    [ 8.316909] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0460)
    [ 8.316909] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 8.568520] input: Power Button (FF) as /class/input/input4
    [ 8.620819] ACPI: Power Button (FF) [PWRF]
    [ 8.620945] input: Power Button (CM) as /class/input/input5
    [ 8.669703] ACPI: Power Button (CM) [PWRB]
    [ 9.048402] Error: Driver 'pcspkr' is already registered, aborting...
    [ 9.068403] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
    [ 9.068403] PCI: Setting latency timer of device 0000:00:1b.0 to 64
    [ 9.104403] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
    [ 9.888929] Adding 1847432k swap on /dev/sda12. Priority:-1 extents:1 across:1847432k
    [ 10.222051] EXT3 FS on sda6, internal journal
    [ 10.641805] it87: Found IT8718F chip at 0x290, revision 3
    [ 10.641805] it87: in3 is VCC (+5V)
    [ 10.641805] it87: in7 is VCCH (+5V Stand-By)
    [ 10.657357] coretemp coretemp.0: Using relative temperature scale!
    [ 10.657357] coretemp coretemp.1: Using relative temperature scale!
    [ 10.745725] device-mapper: uevent: version 1.0.3
    [ 10.745725] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
    [ 26.582047] kjournald starting. Commit interval 5 seconds
    [ 26.582047] EXT3 FS on sda10, internal journal
    [ 26.582047] EXT3-fs: mounted filesystem with ordered data mode.
    [ 26.605941] kjournald starting. Commit interval 5 seconds
    [ 26.605941] EXT3 FS on sda8, internal journal
    [ 26.605941] EXT3-fs: mounted filesystem with ordered data mode.
    [ 26.641371] kjournald starting. Commit interval 5 seconds
    [ 26.641371] EXT3-fs: mounted filesystem with ordered data mode.
    [ 26.661274] kjournald starting. Commit interval 5 seconds
    [ 26.661274] EXT3-fs: mounted filesystem with ordered data mode.
    [ 26.677206] kjournald starting. Commit interval 5 seconds
    [ 26.677206] EXT3-fs: mounted filesystem with ordered data mode.
    [ 29.971694] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [ 29.971758] eth0: 10/100 speed: disabling TSO
    [ 42.084477] NET: Registered protocol family 10
    [ 42.085051] lo: Disabled Privacy Extensions
    [ 42.899159] lp: driver loaded but no devices found
    [ 42.955150] ppdev: user-space parallel port driver
    [ 44.514082] RPC: Registered udp transport module.
    [ 44.514082] RPC: Registered tcp transport module.
    [ 44.540877] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    [ 44.588337] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    [ 44.603502] NFSD: starting 90-second grace period
    [ 45.513208] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
    [ 50.493377] [drm] Initialized drm 1.1.0 20060810
    [ 50.507808] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
    [ 50.507819] PCI: Setting latency timer of device 0000:00:02.0 to 64
    [ 50.507903] [drm] Initialized i915 1.6.0 20060119 on minor 0
    [ 51.063638] set status page addr 0x00033000
    [ 72.047875] UDF-fs: Partition marked readonly; forcing readonly mount
    [ 72.079879] UDF-fs INFO UDF: Mounting volume 'VIIS', timestamp 2007/08/30 17:19 (1078)
    [ 120.622085] ACPI: PCI interrupt for device 0000:00:19.0 disabled
    [ 161.188681] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
    [ 161.188681] e1000e: Copyright (c) 1999-2008 Intel Corporation.
    [ 161.188681] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
    [ 161.188681] PCI: Setting latency timer of device 0000:00:19.0 to 64
    [ 161.278868] eth0: (PCI Express:2.5GB/s:Width x1) 00:1d:09:78:34:2b
    [ 161.278874] eth0: Intel(R) PRO/10/100 Network Connection
    [ 161.278900] eth0: MAC: 5, PHY: 7, PBA No: ffffff-0ff
    [ 161.321589] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 162.876381] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [ 162.876381] eth0: 10/100 speed: disabling TSO
    [ 162.876381] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 175.200514] eth0: no IPv6 routers present
    [ 207.020907] ACPI: PCI interrupt for device 0000:00:19.0 disabled
    [ 209.857248] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
    [ 209.857255] Copyright (c) 1999-2006 Intel Corporation.
    [ 261.918883] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
    [ 261.918883] e1000e: Copyright (c) 1999-2008 Intel Corporation.
    [ 261.918883] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
    [ 261.918883] PCI: Setting latency timer of device 0000:00:19.0 to 64
    [ 262.006886] eth0: (PCI Express:2.5GB/s:Width x1) 00:1d:09:78:34:2b
    [ 262.006886] eth0: Intel(R) PRO/10/100 Network Connection
    [ 262.006886] eth0: MAC: 5, PHY: 7, PBA No: ffffff-0ff
    [ 262.050364] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 263.799046] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [ 263.799053] eth0: 10/100 speed: disabling TSO
    [ 263.799283] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 320.581736] ACPI: PCI interrupt for device 0000:00:19.0 disabled
    [ 325.196148] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
    [ 325.196148] e1000e: Copyright (c) 1999-2008 Intel Corporation.
    [ 325.196148] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
    [ 325.196148] PCI: Setting latency timer of device 0000:00:19.0 to 64
    [ 325.282805] eth0: (PCI Express:2.5GB/s:Width x1) 00:1d:09:78:34:2b
    [ 325.282811] eth0: Intel(R) PRO/10/100 Network Connection
    [ 325.282837] eth0: MAC: 5, PHY: 7, PBA No: ffffff-0ff
    [ 325.330808] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 327.014511] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
    [ 327.014517] eth0: 10/100 speed: disabling TSO
    [ 327.014760] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 1182.677148] EXT3 FS on sda7, internal journal

    ** Loaded modules:
    Module Size Used by
    e1000e 84612 0
    nfs 213896 2
    udf 67748 1
    nls_base 6820 1 udf
    crc_itu_t 2080 1 udf
    i915 25280 2
    drm 65256 3 i915
    binfmt_misc 7528 1
    nfsd 186704 13
    lockd 54248 2 nfs,nfsd
    nfs_acl 2912 2 nfs,nfsd
    auth_rpcgss 33952 1 nfsd
    sunrpc 162176 19 nfs,nfsd,lockd,nfs_acl,auth_rpcgss
    exportfs 3904 1 nfsd
    ppdev 6468 0
    parport_pc 22500 0
    lp 8164 0
    parport 30988 3 ppdev,parport_pc,lp
    ipv6 235172 39
    dm_crypt 11172 0
    crypto_blkcipher 15236 1 dm_crypt
    dm_mod 46184 1 dm_crypt
    coretemp 5504 0
    it87 17744 0
    hwmon_vid 2720 1 it87
    snd_hda_intel 324248 1
    snd_pcm_oss 32800 0
    snd_pcm 62628 2 snd_hda_intel,snd_pcm_oss
    snd_mixer_oss 12320 1 snd_pcm_oss
    snd_seq_dummy 2660 0
    snd_seq_oss 24992 0
    snd_seq_midi 5728 0
    snd_rawmidi 18560 1 snd_seq_midi
    button 6064 0
    snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
    snd_seq 41456 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
    snd_timer 17800 2 snd_pcm,snd_seq
    snd_seq_device 6380 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
    snd 45604 11 snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
    soundcore 6368 1 snd
    snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
    iTCO_wdt 9508 0
    dcdbas 6272 0
    intel_agp 22300 1
    evdev 8000 4
    agpgart 28776 3 drm,intel_agp
    psmouse 32336 0
    serio_raw 4740 0
    i2c_i801 7920 0
    i2c_core 19828 1 i2c_i801
    pcspkr 2432 0
    ext3 105256 6
    jbd 39444 1 ext3
    mbcache 7108 1 ext3
    sg 26964 0
    sr_mod 13316 1
    cdrom 30176 1 sr_mod
    sd_mod 22200 8
    ide_pci_generic 3908 0 [permanent]
    ide_core 92628 1 ide_pci_generic
    ata_generic 4676 0
    usbhid 35904 0
    hid 33184 1 usbhid
    ff_memless 4392 1 usbhid
    floppy 47716 0
    ata_piix 14180 8
    libata 140416 2 ata_generic,ata_piix
    scsi_mod 129356 4 sg,sr_mod,sd_mod,libata
    dock 8272 1 libata
    ehci_hcd 28428 0
    uhci_hcd 18672 0
    usbcore 118160 4 usbhid,ehci_hcd,uhci_hcd
    thermal 15228 0
    processor 32576 1 thermal
    fan 4164 0
    thermal_sys 10856 3 thermal,processor,fan

    ** PCI devices:
    00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Capabilities:
    Kernel driver in use: agpgart-intel
    Kernel modules: intel-agp

    00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port [8086:29c1] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fde00000-fdefffff
    Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:
    Kernel driver in use: pcieport-driver
    Kernel modules: shpchp

    00:02.0 VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express Integrated Graphics Controller [8086:29c2] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at ff00 [size=8]
    Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at fdb00000 (32-bit, non-prefetchable) [size=1M]
    Capabilities:

    00:19.0 Ethernet controller [0200]: Intel Corporation 82562V-2 10/100 Network Connection [8086:10c0] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 222
    Region 0: Memory at fdfc0000 (32-bit, non-prefetchable) [size=128K]
    Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]
    Region 2: I/O ports at fe00 [size=32]
    Capabilities:
    Kernel driver in use: e1000e
    Kernel modules: e1000e

    00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 4: I/O ports at fd00 [size=32]
    Capabilities:
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 21
    Region 4: I/O ports at fc00 [size=32]
    Capabilities:
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin D routed to IRQ 19
    Region 4: I/O ports at fb00 [size=32]
    Capabilities:
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20)
    Subsystem: Dell Device [1028:0238]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin C routed to IRQ 18
    Region 0: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
    Capabilities:
    Kernel driver in use: ehci_hcd
    Kernel modules: ehci-hcd

    00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 22
    Region 0: Memory at fdff4000 (64-bit, non-prefetchable) [size=16K]
    Capabilities:
    Kernel driver in use: HDA Intel
    Kernel modules: snd-hda-intel

    00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 4: I/O ports at fa00 [size=32]
    Capabilities:
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 4: I/O ports at f900 [size=32]
    Capabilities:
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin C routed to IRQ 18
    Region 4: I/O ports at f800 [size=32]
    Capabilities:
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20)
    Subsystem: Dell Device [1028:0238]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at fdffd000 (32-bit, non-prefetchable) [size=1K]
    Capabilities:
    Kernel driver in use: ehci_hcd
    Kernel modules: ehci-hcd

    00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fdd00000-fddfffff
    Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:

    00:1f.0 ISA bridge [0601]: Intel Corporation 82801IR (ICH9R) LPC Interface Controller [8086:2916] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Capabilities:
    Kernel modules: iTCO_wdt

    00:1f.2 IDE interface [0101]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 4 port SATA IDE Controller [8086:2920] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 19
    Region 0: I/O ports at f700 [size=8]
    Region 1: I/O ports at f600 [size=4]
    Region 2: I/O ports at f500 [size=8]
    Region 3: I/O ports at f400 [size=4]
    Region 4: I/O ports at f300 [size=16]
    Region 5: I/O ports at f200 [size=16]
    Capabilities:
    Kernel driver in use: ata_piix
    Kernel modules: ata_piix

    00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 02)
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 18
    Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=256]
    Region 4: I/O ports at 0500 [size=32]
    Kernel driver in use: i801_smbus
    Kernel modules: i2c-i801

    00:1f.5 IDE interface [0101]: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller [8086:2926] (rev 02) (prog-if 85 [Master SecO PriO])
    Subsystem: Dell Device [1028:0238]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 19
    Region 0: I/O ports at f000 [size=8]
    Region 1: I/O ports at ef00 [size=4]
    Region 2: I/O ports at ee00 [size=8]
    Region 3: I/O ports at ed00 [size=4]
    Region 4: I/O ports at ec00 [size=16]
    Region 5: I/O ports at eb00 [size=16]
    Capabilities:
    Kernel driver in use: ata_piix
    Kernel modules: ata_piix



    -- System Information:
    Debian Release: lenny/sid
    APT prefers gutsy
    APT policy: (500, 'gutsy'), (500, 'testing')
    Architecture: i386 (i686)

    Kernel: Linux 2.6.26-1-686 (SMP w/2 CPU cores)
    Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
    Shell: /bin/sh linked to /bin/bash

    Versions of packages linux-image-2.6.26-1-686 depends on:
    ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
    ii initramfs-tools [linux-initra 0.92f tools for generating an initramfs
    ii module-init-tools 3.4-1 tools for managing Linux kernel mo

    Versions of packages linux-image-2.6.26-1-686 recommends:
    ii libc6-i686 2.7-13 GNU C Library: Shared libraries [i

    Versions of packages linux-image-2.6.26-1-686 suggests:
    ii grub 0.97-46 GRand Unified Bootloader (Legacy v
    pn linux-doc-2.6.26 (no description available)

    -- debconf information:
    linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
    shared/kernel-image/really-run-bootloader: true
    linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
    linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
    linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
    linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
    linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
    linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
    linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
    linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
    linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
    linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
    linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
    linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
    linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
    linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
    linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
    linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
    linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
    linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
    linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:



    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

  2. Bug#497392: e1000e driver does not initialize correctly

    On Mon, Sep 01, 2008 at 02:22:00PM +0200, Bastien Durel wrote:
    > The e1000e kernel module does not initialize correctly, then the network cannot initialize.


    Please explain, the attached log does not show strange e1000 related
    messages.

    > 00:19.0 Ethernet controller [0200]: Intel Corporation 82562V-2 10/100 Network Connection [8086:10c0] (rev 02)
    > Subsystem: Dell Device [1028:0238]


    Which sort of controller is this?

    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- > Latency: 0
    > Interrupt: pin A routed to IRQ 222
    > Region 0: Memory at fdfc0000 (32-bit, non-prefetchable) [size=128K]
    > Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]
    > Region 2: I/O ports at fe00 [size=32]
    > Capabilities:
    > Kernel driver in use: e1000e
    > Kernel modules: e1000e


    Mine is know to work.

    02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit Ethernet Controller [8086:109a]
    Subsystem: Lenovo Device [17aa:207e]
    Flags: bus master, fast devsel, latency 0, IRQ 218
    Memory at ee000000 (32-bit, non-prefetchable) [size=128K]
    I/O ports at 2000 [size=32]
    Capabilities:
    Kernel driver in use: e1000e
    Kernel modules: e1000e

    Bstian

    --
    Too much of anything, even love, isn't necessarily a good thing.
    -- Kirk, "The Trouble with Tribbles", stardate 4525.6



    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

  3. Bug#497392: e1000e driver does not initialize correctly

    On Mon, Sep 22, 2008 at 01:44:38PM +0200, Bastien Durel wrote:
    > Le dimanche 21 septembre 2008 à 15:14 +0200, Bastian Blank a écrit :
    > > On Mon, Sep 01, 2008 at 02:22:00PM +0200, Bastien Durel wrote:
    > > > The e1000e kernel module does not initialize correctly, then the network cannot initialize.

    > >
    > > Please explain, the attached log does not show strange e1000 related
    > > messages.
    > >

    > Well,
    >
    > when the module is inserted, nothing complains, the RAs are recevied,
    > but ipv4 cannot be used on the interface. DHCP does not respond, and
    > manual configuration does not allow packets to reach another computer.
    > tcpdump on the router does not show any packet going from the computer
    > during DHCP or after manual configuration.
    >
    > After a few(exact number may change) rmmod's modprobe's, IPv4 can goes
    > through interface. *That's* very strange.


    Is this behaviour also reproducible if you try a current 2.6.28-rcX
    kernel? If so, could you file a report at bugzilla.kernel.org?

    Cheers,
    Moritz



    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

+ Reply to Thread