Bug#491355: Laptop intermittent freeze after upgrade to linux-image-2.6.25-2-amd64 - Debian

This is a discussion on Bug#491355: Laptop intermittent freeze after upgrade to linux-image-2.6.25-2-amd64 - Debian ; Package: linux-image-2.6.25-2-amd64 Version: 2.6.25-6 Severity: normal While running my Dell Latitude D830 on battery, after ~30 seconds of not using the mouse or keyboard, attempting to move the mouse will result in a series of 2-second pauses, with about 1/4 ...

+ Reply to Thread
Results 1 to 2 of 2

Thread: Bug#491355: Laptop intermittent freeze after upgrade to linux-image-2.6.25-2-amd64

  1. Bug#491355: Laptop intermittent freeze after upgrade to linux-image-2.6.25-2-amd64

    Package: linux-image-2.6.25-2-amd64
    Version: 2.6.25-6
    Severity: normal

    While running my Dell Latitude D830 on battery, after ~30 seconds of not using the mouse or keyboard, attempting to move the mouse will result in a series of 2-second pauses, with about 1/4 second of activity between them (2 second pause, pointer jumps, 2 second pause, pointer jumps). After two or three of these intermittent pauses, the computer will respond normally until the keyboard/mouse is left for ~30 seconds.

    I first noticed this while listening to music, since anytime after the ~30 second mark, the last played sample will loop infinitely until there is keyboard/mouse activity.

    I have encountered this issue on a number of distributions, but not Debian until this latest kernel upgrade. I was running 2.6.24-7 previously.


    -- Package-specific info:
    ** Version:Linux version 2.6.25-2-amd64 (Debian 2.6.25-6) (maks@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Fri Jun 27 00:16:12 UTC 2008

    ** Command line:
    root=UUID=5c281424-7eb3-46e1-b140-018a1bdcb232 ro quiet

    ** Not tainted

    ** Kernel log:
    [ 162.261650] USB Mass Storage support registered.
    [ 167.242905] usb-storage: device scan complete
    [ 167.247110] scsi 3:0:0:0: Direct-Access LEXAR JD FIREFLY 1100 PQ: 0 ANSI: 0 CCS
    [ 167.250440] sd 3:0:0:0: [sdb] 1966080 512-byte hardware sectors (1007 MB)
    [ 167.251434] sd 3:0:0:0: [sdb] Write Protect is off
    [ 167.251443] sd 3:0:0:0: [sdb] Mode Sense: 43 00 00 00
    [ 167.251448] sd 3:0:0:0: [sdb] Assuming drive cache: write through
    [ 167.254176] sd 3:0:0:0: [sdb] 1966080 512-byte hardware sectors (1007 MB)
    [ 167.255076] sd 3:0:0:0: [sdb] Write Protect is off
    [ 167.255085] sd 3:0:0:0: [sdb] Mode Sense: 43 00 00 00
    [ 167.255090] sd 3:0:0:0: [sdb] Assuming drive cache: write through
    [ 167.255096] sdb: sdb1
    [ 167.308762] sd 3:0:0:0: [sdb] Attached SCSI removable disk
    [ 167.250031] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
    [ 498.809607] usb 7-1: USB disconnect, address 3
    [10011.853883] Clocksource tsc unstable (delta = -126769364 ns)
    [10733.979812] atkbd.c: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
    [10733.979812] atkbd.c: Use 'setkeycodes e00d ' to make it known.
    [10769.289677] CPU0 attaching NULL sched-domain.
    [10769.289694] CPU1 attaching NULL sched-domain.
    [10769.310630] CPU0 attaching sched-domain:
    [10769.310642] domain 0: span 00000003
    [10769.310651] groups: 00000001 00000002
    [10769.310663] domain 1: span 00000003
    [10769.310668] groups: 00000003
    [10769.310678] domain 2: span 00000003
    [10769.310691] groups: 00000003
    [10769.310711] CPU1 attaching sched-domain:
    [10769.310720] domain 0: span 00000003
    [10769.310731] groups: 00000002 00000001
    [10769.310756] domain 1: span 00000003
    [10769.310761] groups: 00000003
    [10769.310777] domain 2: span 00000003
    [10769.310787] groups: 00000003
    [10772.220068] ACPI: PCI interrupt for device 0000:0c:00.0 disabled
    [10811.287863] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
    [10811.288050] PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100102, writing 100106)
    [10811.349366] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [10773.675225] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [10776.502668] tg3: eth0: Link is up at 1000 Mbps, full duplex.
    [10776.502668] tg3: eth0: Flow control is off for TX and off for RX.
    [10776.502668] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [10776.980016] tg3: eth0: Link is down.
    [10779.325935] tg3: eth0: Link is up at 1000 Mbps, full duplex.
    [10779.325935] tg3: eth0: Flow control is off for TX and off for RX.
    [10779.325935] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [10779.806047] tg3: eth0: Link is down.
    [10782.144829] tg3: eth0: Link is up at 1000 Mbps, full duplex.
    [10782.144829] tg3: eth0: Flow control is off for TX and off for RX.
    [10834.465222] eth0: no IPv6 routers present
    [11230.565450] atkbd.c: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
    [11230.565465] atkbd.c: Use 'setkeycodes e00d ' to make it known.
    [11287.226787] CPU0 attaching NULL sched-domain.
    [11287.226802] CPU1 attaching NULL sched-domain.
    [11287.256769] CPU0 attaching sched-domain:
    [11287.256780] domain 0: span 00000003
    [11287.256786] groups: 00000001 00000002
    [11287.256794] domain 1: span 00000003
    [11287.256798] groups: 00000003
    [11287.256806] CPU1 attaching sched-domain:
    [11287.256810] domain 0: span 00000003
    [11287.256814] groups: 00000002 00000001
    [11287.256821] domain 1: span 00000003
    [11287.256826] groups: 00000003
    [11230.741013] psmouse.c: GlidePoint at isa0060/serio1/input0 lost synchronization, throwing 2 bytes away.
    [11289.695821] psmouse.c: resync failed, issuing reconnect request
    [11914.029286] atkbd.c: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
    [11914.029286] atkbd.c: Use 'setkeycodes e00d ' to make it known.
    [11914.128226] CPU0 attaching NULL sched-domain.
    [11914.128244] CPU1 attaching NULL sched-domain.
    [11914.146148] CPU0 attaching sched-domain:
    [11914.146168] domain 0: span 00000003
    [11914.146173] groups: 00000001 00000002
    [11914.146185] domain 1: span 00000003
    [11914.146193] groups: 00000003
    [11914.146199] domain 2: span 00000003
    [11914.146207] groups: 00000003
    [11914.146214] CPU1 attaching sched-domain:
    [11914.146222] domain 0: span 00000003
    [11914.146226] groups: 00000002 00000001
    [11914.146237] domain 1: span 00000003
    [11914.146242] groups: 00000003
    [11914.146251] domain 2: span 00000003
    [11914.146256] groups: 00000003
    [11934.803539] wlan0: Initial auth_alg=0
    [11934.803554] wlan0: authenticate with AP 00:0b:0e:94:fe:80
    [11934.805562] wlan0: RX authentication from 00:0b:0e:94:fe:80 (alg=0 transaction=2 status=0)
    [11934.805572] wlan0: authenticated
    [11934.805578] wlan0: associate with AP 00:0b:0e:94:fe:80
    [11871.772781] wlan0: RX AssocResp from 00:0b:0e:94:fe:80 (capab=0x31 status=0 aid=7)
    [11871.772793] wlan0: associated
    [11871.772803] wlan0: CTS protection enabled (BSSID=00:0b:0e:94:fe:80)
    [11871.772811] wlan0: switched to short barker preamble (BSSID=00:0b:0e:94:fe:80)
    [11871.772918] wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
    [11871.772925] wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
    [11871.772932] wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
    [11871.772938] wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
    [11871.774166] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [11883.163252] ACPI: PCI interrupt for device 0000:09:00.0 disabled
    [11889.641182] wlan0: no IPv6 routers present

    ** Loaded modules:
    Module Size Used by
    nls_utf8 6528 0
    nls_cp437 11392 0
    vfat 17920 0
    fat 57016 1 vfat
    nls_base 13444 4 nls_utf8,nls_cp437,vfat,fat
    usb_storage 94400 0
    i915 37632 1
    drm 99112 2 i915
    rfcomm 46112 0
    l2cap 29696 5 rfcomm
    bluetooth 65444 4 rfcomm,l2cap
    ipv6 294120 16
    ppdev 13832 0
    parport_pc 34344 0
    lp 17540 0
    parport 44848 3 ppdev,parport_pc,lp
    acpi_cpufreq 14096 2
    cpufreq_userspace 9092 0
    cpufreq_powersave 6272 0
    cpufreq_conservative 13320 0
    cpufreq_stats 10528 0
    cpufreq_ondemand 13712 1
    freq_table 9728 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
    ext2 76304 1
    fuse 53440 1
    ext3 139408 1
    jbd 55336 1 ext3
    mbcache 13956 2 ext2,ext3
    sha256_generic 13952 0
    aes_x86_64 12928 7
    aes_generic 32424 1 aes_x86_64
    cbc 8960 3
    dm_crypt 20488 1
    dm_mod 68536 7 dm_crypt
    loop 23044 0
    firewire_sbp2 22808 0
    joydev 17664 0
    arc4 6528 2
    ecb 8192 2
    crypto_blkcipher 24324 6 cbc,dm_crypt,ecb
    snd_hda_intel 414296 1
    snd_pcm_oss 46752 0
    snd_mixer_oss 21376 1 snd_pcm_oss
    pcmcia 45080 0
    iwl3945 98036 0
    snd_pcm 88072 2 snd_hda_intel,snd_pcm_oss
    snd_timer 29328 1 snd_pcm
    firmware_class 14976 2 pcmcia,iwl3945
    snd 66888 7 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_timer
    mac80211 143244 1 iwl3945
    psmouse 45724 0
    iTCO_wdt 17360 0
    soundcore 13088 1 snd
    yenta_socket 31500 1
    i2c_i801 15260 0
    serio_raw 11652 0
    cfg80211 25360 1 mac80211
    snd_page_alloc 15120 2 snd_hda_intel,snd_pcm
    rsrc_nonstatic 16128 1 yenta_socket
    pcmcia_core 46500 3 pcmcia,yenta_socket,rsrc_nonstatic
    i2c_core 30752 1 i2c_i801
    video 27412 0
    output 8704 1 video
    bay 11392 0
    wmi 13120 0
    battery 14208 0
    button 13856 0
    ac 9344 0
    intel_agp 34160 1
    dcdbas 13616 0
    evdev 17408 7
    xfs 492968 2
    sd_mod 33728 6
    ide_cd_mod 41504 0
    cdrom 39464 1 ide_cd_mod
    ata_generic 13572 0
    ide_pci_generic 9476 0 [permanent]
    ahci 36616 5
    libata 166064 2 ata_generic,ahci
    scsi_mod 170488 4 usb_storage,firewire_sbp2,sd_mod,libata
    firewire_ohci 27908 0
    firewire_core 45920 2 firewire_sbp2,firewire_ohci
    crc_itu_t 6656 1 firewire_core
    piix 12808 0 [permanent]
    ide_core 138160 3 ide_cd_mod,ide_pci_generic,piix
    ehci_hcd 40076 0
    dock 16288 2 bay,libata
    uhci_hcd 29472 0
    thermal 26656 0
    processor 49388 4 acpi_cpufreq,thermal
    fan 10760 0

    ** PCI devices:
    00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 0c)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Capabilities:
    Kernel driver in use: agpgart-intel
    Kernel modules: intel-agp

    00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 0c)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=1M]
    Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
    Region 4: I/O ports at eff8 [size=8]
    Capabilities:

    00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a03] (rev 0c)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Region 0: Memory at feb00000 (64-bit, non-prefetchable) [size=1M]
    Capabilities:

    00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 20
    Region 4: I/O ports at 6f20 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 21
    Region 4: I/O ports at 6f00 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin C routed to IRQ 22
    Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
    Capabilities:
    Kernel driver in use: ehci_hcd
    Kernel modules: ehci-hcd

    00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 21
    Region 0: Memory at fe9fc000 (64-bit, non-prefetchable) [size=16K]
    Capabilities:
    Kernel driver in use: HDA Intel
    Kernel modules: snd-hda-intel

    00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:
    Kernel driver in use: pcieport-driver
    Kernel modules: shpchp

    00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
    Memory behind bridge: fe800000-fe8fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:
    Kernel driver in use: pcieport-driver
    Kernel modules: shpchp

    00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 [8086:2845] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fe600000-fe7fffff
    Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:
    Kernel driver in use: pcieport-driver
    Kernel modules: shpchp

    00:1c.5 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 [8086:2849] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
    Memory behind bridge: fe500000-fe5fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:
    Kernel driver in use: pcieport-driver
    Kernel modules: shpchp

    00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 20
    Region 4: I/O ports at 6f80 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 21
    Region 4: I/O ports at 6f60 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin C routed to IRQ 22
    Region 4: I/O ports at 6f40 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 20
    Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
    Capabilities:
    Kernel driver in use: ehci_hcd
    Kernel modules: ehci-hcd

    00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f2) (prog-if 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Bus: primary=00, secondary=03, subordinate=07, sec-latency=32
    I/O behind bridge: 00002000-00002fff
    Memory behind bridge: fe400000-fe4fffff
    Prefetchable memory behind bridge: 0000000088000000-000000008bffffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities:

    00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Capabilities:
    Kernel modules: iTCO_wdt

    00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 02) (prog-if 8a [Master SecP PriP])
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: I/O ports at 01f0 [size=8]
    Region 1: I/O ports at 03f4 [size=1]
    Region 2: I/O ports at 0170 [size=8]
    Region 3: I/O ports at 0374 [size=1]
    Region 4: I/O ports at 6fa0 [size=16]
    Kernel driver in use: PIIX_IDE
    Kernel modules: ata_generic, piix, ide-pci-generic

    00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 02) (prog-if 01)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 1275
    Region 0: I/O ports at 6eb0 [size=8]
    Region 1: I/O ports at 6eb8 [size=4]
    Region 2: I/O ports at 6ec0 [size=8]
    Region 3: I/O ports at 6ec8 [size=4]
    Region 4: I/O ports at 6ee0 [size=32]
    Region 5: Memory at fe9fb800 (32-bit, non-prefetchable) [size=2K]
    Capabilities:
    Kernel driver in use: ahci
    Kernel modules: ahci

    00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 17
    Region 0: Memory at fe9fb700 (32-bit, non-prefetchable) [size=256]
    Region 4: I/O ports at 10c0 [size=32]
    Kernel driver in use: i801_smbus
    Kernel modules: i2c-i801

    03:01.0 CardBus bridge [0607]: O2 Micro, Inc. Cardbus bridge [1217:7135] (rev 21)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- SERR- Latency: 168
    Interrupt: pin A routed to IRQ 19
    Region 0: Memory at fe400000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
    Memory window 0: 88000000-8bfff000 (prefetchable)
    Memory window 1: 8c000000-8ffff000
    I/O window 0: 00002000-000020ff
    I/O window 1: 00002400-000024ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001
    Kernel driver in use: yenta_cardbus
    Kernel modules: yenta_socket

    03:01.4 FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Firewire (IEEE 1394) [1217:00f7] (rev 02) (prog-if 10)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 64, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 19
    Region 0: Memory at fe4ff000 (32-bit, non-prefetchable) [size=4K]
    Region 1: Memory at fe4fe800 (32-bit, non-prefetchable) [size=2K]
    Capabilities:
    Kernel driver in use: firewire_ohci
    Kernel modules: firewire-ohci

    09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express [14e4:1673] (rev 02)
    Subsystem: Dell Device [1028:01fe]
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Interrupt: pin A routed to IRQ 17
    Region 0: Memory at fe5f0000 (64-bit, non-prefetchable) [size=64K]
    Expansion ROM at [disabled]
    Capabilities:
    Kernel modules: tg3

    0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG Network Connection [8086:4222] (rev 02)
    Subsystem: Intel Corporation Device [8086:1020]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 1274
    Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=4K]
    Capabilities:
    Kernel driver in use: iwl3945
    Kernel modules: iwl3945



    -- System Information:
    Debian Release: lenny/sid
    APT prefers testing
    APT policy: (500, 'testing')
    Architecture: amd64 (x86_64)

    Kernel: Linux 2.6.25-2-amd64 (SMP w/2 CPU cores)
    Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
    Shell: /bin/sh linked to /bin/bash

    Versions of packages linux-image-2.6.25-2-amd64 depends on:
    ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
    ii initramfs-tools [linux-initra 0.92e tools for generating an initramfs
    ii module-init-tools 3.4-1 tools for managing Linux kernel mo

    linux-image-2.6.25-2-amd64 recommends no packages.

    -- debconf information:
    shared/kernel-image/really-run-bootloader: true
    linux-image-2.6.25-2-amd64/prerm/removing-running-kernel-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/preinst/abort-overwrite-2.6.25-2-amd64:
    linux-image-2.6.25-2-amd64/postinst/old-initrd-link-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/postinst/create-kimage-link-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/preinst/failed-to-move-modules-2.6.25-2-amd64:
    linux-image-2.6.25-2-amd64/preinst/abort-install-2.6.25-2-amd64:
    linux-image-2.6.25-2-amd64/postinst/kimage-is-a-directory:
    linux-image-2.6.25-2-amd64/postinst/depmod-error-2.6.25-2-amd64: false
    linux-image-2.6.25-2-amd64/postinst/bootloader-test-error-2.6.25-2-amd64:
    linux-image-2.6.25-2-amd64/postinst/old-system-map-link-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/prerm/would-invalidate-boot-loader-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/preinst/overwriting-modules-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/postinst/depmod-error-initrd-2.6.25-2-amd64: false
    linux-image-2.6.25-2-amd64/postinst/old-dir-initrd-link-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/preinst/elilo-initrd-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/postinst/bootloader-error-2.6.25-2-amd64:
    linux-image-2.6.25-2-amd64/preinst/lilo-initrd-2.6.25-2-amd64: true
    linux-image-2.6.25-2-amd64/preinst/lilo-has-ramdisk:
    linux-image-2.6.25-2-amd64/preinst/initrd-2.6.25-2-amd64:
    linux-image-2.6.25-2-amd64/preinst/bootloader-initrd-2.6.25-2-amd64: true






    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

  2. Bug#491355: Laptop intermittent freeze after upgrade to linux-image-2.6.25-2-amd64

    On Fri, Jul 18, 2008 at 01:36:48PM -0700, ben grindy wrote:
    > Package: linux-image-2.6.25-2-amd64
    > Version: 2.6.25-6
    > Severity: normal
    >
    > While running my Dell Latitude D830 on battery, after ~30 seconds of not using the mouse or keyboard, attempting to move the mouse will result in a series of 2-second pauses, with about 1/4 second of activity between them (2 second pause, pointer jumps, 2 second pause, pointer jumps). After two or three of these intermittent pauses, the computer will respond normally until the keyboard/mouse is left for ~30 seconds.
    >
    > I first noticed this while listening to music, since anytime after the ~30 second mark, the last played sample will loop infinitely until there is keyboard/mouse activity.
    >
    > I have encountered this issue on a number of distributions, but not Debian until this latest kernel upgrade. I was running 2.6.24-7 previously.


    Does this behaviour still occur with the 2.6.26 based kernel from Lenny?

    Cheers,
    Moritz



    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

+ Reply to Thread