Bug#475134: linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg - Debian

This is a discussion on Bug#475134: linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg - Debian ; Package: linux-image-2.6.24-1-686 Version: 2.6.24-4 Severity: normal I'am experiencing kernel panic when copying large files (>20M) over FTP, using wi-fi card Edimax EW-7108Pcg. It's 100% repeatable. So I am ready to test it a send traces of whatever is needed to ...

+ Reply to Thread
Results 1 to 3 of 3

Thread: Bug#475134: linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg

  1. Bug#475134: linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg

    Package: linux-image-2.6.24-1-686
    Version: 2.6.24-4
    Severity: normal

    I'am experiencing kernel panic when copying large files (>20M) over FTP,
    using wi-fi card Edimax EW-7108Pcg. It's 100% repeatable. So I am ready
    to test it a send traces of whatever is needed to fix it. But I don't
    know, how to save the trace. I could make a screen photo, or copy trace
    text by eyes. Ready to answer.


    -- Package-specific info:
    ** Kernel log:
    EXT3 FS on hda1, internal journal
    device-mapper: uevent: version 1.0.3
    device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
    input: PS/2 Generic Mouse as /class/input/input7
    fuse init (API version 7.9)
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda6, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    ADDRCONF(NETDEV_UP): wlan0: link is not ready
    lp0: using parport0 (interrupt-driven).
    ppdev: user-space parallel port driver
    eth0: setting half-duplex.
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    [drm] Initialized drm 1.1.0 20060810
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    [drm] Initialized radeon 1.28.0 20060524 on minor 0
    agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
    agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
    agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
    [drm] Setting GART location based on new memory map
    [drm] writeback test succeeded in 2 usecs
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:14:1b:5b:7f:10
    wlan0: RX authentication from 00:14:1b:5b:7f:10 (alg=0 transaction=2 status=0)
    wlan0: authenticated
    wlan0: associate with AP 00:14:1b:5b:7f:10
    wlan0: RX AssocResp from 00:14:1b:5b:7f:10 (capab=0x431 status=0 aid=18)
    wlan0: associated
    wlan0: switched to short barker preamble (BSSID=00:14:1b:5b:7f:10)
    wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
    wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
    ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:14:1b:5b:7f:10
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:12:01:b5:66:00
    wlan0: RX authentication from 00:12:01:b5:66:00 (alg=0 transaction=2 status=0)
    wlan0: authenticated
    wlan0: associate with AP 00:12:01:b5:66:00
    wlan0: RX ReassocResp from 00:12:01:b5:66:00 (capab=0x431 status=0 aid=102)
    wlan0: associated
    wlan0: CTS protection enabled (BSSID=00:12:01:b5:66:00)
    wlan0: switched to long barker preamble (BSSID=00:12:01:b5:66:00)
    wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
    wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:12:01:b5:66:00
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:14:1b:5b:7f:10
    wlan0: RX authentication from 00:14:1b:5b:7f:10 (alg=0 transaction=2 status=0)
    wlan0: authenticated
    wlan0: associate with AP 00:14:1b:5b:7f:10
    wlan0: RX ReassocResp from 00:14:1b:5b:7f:10 (capab=0x431 status=0 aid=22)
    wlan0: associated
    wlan0: CTS protection disabled (BSSID=00:14:1b:5b:7f:10)
    wlan0: switched to short barker preamble (BSSID=00:14:1b:5b:7f:10)
    wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
    wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
    wlan0: CTS protection enabled (BSSID=00:14:1b:5b:7f:10)
    wlan0: CTS protection disabled (BSSID=00:14:1b:5b:7f:10)
    wlan0: CTS protection enabled (BSSID=00:14:1b:5b:7f:10)
    wlan0: CTS protection disabled (BSSID=00:14:1b:5b:7f:10)
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:14:1b:5b:7f:10
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:12:01:b5:66:00
    wlan0: RX authentication from 00:12:01:b5:66:00 (alg=0 transaction=2 status=0)
    wlan0: authenticated
    wlan0: associate with AP 00:12:01:b5:66:00
    wlan0: RX ReassocResp from 00:12:01:b5:66:00 (capab=0x431 status=0 aid=205)
    wlan0: associated
    wlan0: CTS protection enabled (BSSID=00:12:01:b5:66:00)
    wlan0: switched to long barker preamble (BSSID=00:12:01:b5:66:00)
    wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
    wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:12:01:b5:66:00
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:14:1b:5b:7f:10
    wlan0: RX authentication from 00:14:1b:5b:7f:10 (alg=0 transaction=2 status=0)
    wlan0: authenticated
    wlan0: associate with AP 00:14:1b:5b:7f:10
    wlan0: RX ReassocResp from 00:14:1b:5b:7f:10 (capab=0x431 status=0 aid=48)
    wlan0: associated
    wlan0: CTS protection disabled (BSSID=00:14:1b:5b:7f:10)
    wlan0: switched to short barker preamble (BSSID=00:14:1b:5b:7f:10)
    wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
    wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
    wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15

    ** Loaded modules:
    Module Size Used by
    radeon 112096 2
    drm 74132 3 radeon
    ppdev 8804 0
    lp 11076 0
    ipv6 240772 14
    fuse 45204 1
    dm_snapshot 16964 0
    dm_mirror 21600 0
    dm_mod 55812 2 dm_snapshot,dm_mirror
    arc4 2016 2
    ecb 3552 2
    blkcipher 6724 1 ecb
    rt61pci 23072 0
    rt2x00pci 9920 1 rt61pci
    rt2x00lib 20000 2 rt61pci,rt2x00pci
    rfkill 7312 1 rt2x00lib
    input_polldev 5000 1 rt2x00lib
    crc_itu_t 2176 1 rt2x00lib
    mac80211 114380 3 rt61pci,rt2x00pci,rt2x00lib
    cfg80211 13480 1 mac80211
    eeprom_93cx6 2304 1 rt61pci
    joydev 11360 0
    pcmcia 37036 0
    firmware_class 9312 2 rt2x00lib,pcmcia
    irda 174236 0
    crc_ccitt 2176 1 irda
    parport_pc 33668 1
    parport 34280 3 ppdev,lp,parport_pc
    serio_raw 6660 0
    psmouse 36464 0
    pcspkr 3200 0
    yenta_socket 24844 3
    rsrc_nonstatic 11872 1 yenta_socket
    pcmcia_core 36884 3 pcmcia,yenta_socket,rsrc_nonstatic
    rtc 13052 0
    video 18672 0
    output 3744 1 video
    snd_intel8x0 32028 1
    snd_intel8x0m 16844 0
    snd_ac97_codec 92932 2 snd_intel8x0,snd_intel8x0m
    ac97_bus 2176 1 snd_ac97_codec
    snd_pcm_oss 38272 0
    snd_mixer_oss 15296 1 snd_pcm_oss
    snd_pcm 71780 4 snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_ oss
    snd_timer 21092 1 snd_pcm
    button 8432 0
    battery 13572 0
    snd 48612 9 snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_ oss,snd_mixer_oss,snd_pcm,snd_timer
    ac 6116 0
    soundcore 7552 1 snd
    snd_page_alloc 10056 3 snd_intel8x0,snd_intel8x0m,snd_pcm
    iTCO_wdt 11268 0
    shpchp 31028 0
    pci_hotplug 27712 1 shpchp
    intel_agp 23412 1
    agpgart 31688 2 drm,intel_agp
    evdev 11104 6
    ext3 122920 2
    jbd 43732 1 ext3
    mbcache 8288 1 ext3
    ide_disk 15648 4
    piix 7492 0 [permanent]
    generic 4388 0 [permanent]
    ide_core 108292 3 ide_disk,piix,generic
    floppy 54628 0
    ata_generic 7428 0
    uhci_hcd 23376 0
    3c59x 41064 0
    mii 5312 1 3c59x
    libata 144464 1 ata_generic
    scsi_mod 141196 1 libata
    usbcore 132940 2 uhci_hcd
    thermal 16028 0
    processor 36520 2 thermal
    fan 4772 0

    ** PCI devices:
    00:00.0 Host bridge [0600]: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge [8086:1a30] (rev 04)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
    Capabilities:
    Kernel driver in use: agpgart-intel
    Kernel modules: intel-agp

    00:01.0 PCI bridge [0604]: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge [8086:1a31] (rev 04) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 32
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fc000000-fdffffff
    Prefetchable memory behind bridge: e0000000-e7ffffff
    Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Kernel modules: shpchp

    00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02) (prog-if 00 [UHCI])
    Subsystem: Intel Corporation Latitude C640 [8086:4541]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 11
    Region 4: I/O ports at bf80 [size=32]
    Kernel driver in use: uhci_hcd
    Kernel modules: uhci-hcd

    00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 42) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
    Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
    I/O behind bridge: 0000e000-0000ffff
    Memory behind bridge: f4000000-fbffffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Kernel modules: shpchp

    00:1f.0 ISA bridge [0601]: Intel Corporation 82801CAM ISA Bridge (LPC) [8086:248c] (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Kernel modules: iTCO_wdt, intel-rng

    00:1f.1 IDE interface [0101]: Intel Corporation 82801CAM IDE U100 Controller [8086:248a] (rev 02) (prog-if 8a [Master SecP PriP])
    Subsystem: Intel Corporation Latitude C640 [8086:4541]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin A routed to IRQ 11
    Region 0: I/O ports at 01f0 [size=8]
    Region 1: I/O ports at 03f4 [size=1]
    Region 2: I/O ports at 0170 [size=8]
    Region 3: I/O ports at 0374 [size=1]
    Region 4: I/O ports at bfa0 [size=16]
    Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
    Kernel driver in use: PIIX_IDE
    Kernel modules: piix

    00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801CA/CAM AC'97 Audio Controller [8086:2485] (rev 02)
    Subsystem: Cirrus Logic Crystal WMD Audio Codec [1013:5959]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 5
    Region 0: I/O ports at d800 [size=256]
    Region 1: I/O ports at dc80 [size=64]
    Kernel driver in use: Intel ICH
    Kernel modules: snd-intel8x0

    00:1f.6 Modem [0703]: Intel Corporation 82801CA/CAM AC'97 Modem Controller [8086:2486] (rev 02) (prog-if 00 [Generic])
    Subsystem: PCTel Inc Dell Inspiron 2100 internal modem [134d:4c21]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
    Interrupt: pin B routed to IRQ 5
    Region 0: I/O ports at d400 [size=256]
    Region 1: I/O ports at dc00 [size=128]
    Kernel driver in use: Intel ICH Modem
    Kernel modules: snd-intel8x0m

    01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] [1002:4c57] (prog-if 00 [VGA controller])
    Subsystem: Dell Latitude C640 [1028:012a]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32 (2000ns min), Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
    Region 1: I/O ports at c000 [size=256]
    Region 2: Memory at fcff0000 (32-bit, non-prefetchable) [size=64K]
    [virtual] Expansion ROM at fc000000 [disabled] [size=128K]
    Capabilities:
    Kernel modules: radeonfb

    02:00.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 78)
    Subsystem: Dell 3C920 Integrated Fast Ethernet Controller [Latitude C640] [1028:012a]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: I/O ports at ec80 [size=128]
    Region 1: Memory at f8fffc00 (32-bit, non-prefetchable) [size=128]
    Expansion ROM at f8000000 [disabled] [size=128K]
    Capabilities:
    Kernel driver in use: 3c59x
    Kernel modules: 3c59x

    02:01.0 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
    Subsystem: Dell Latitude C640 [1028:012a]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 168, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at f8020000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
    Memory window 0: f4000000-f7fff000 (prefetchable)
    Memory window 1: 34000000-37fff000
    I/O window 0: 0000e000-0000e0ff
    I/O window 1: 0000e400-0000e4ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001
    Kernel driver in use: yenta_cardbus
    Kernel modules: yenta_socket

    02:01.1 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
    Subsystem: Dell Latitude C640 [1028:012a]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 168, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at f8021000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
    Memory window 0: 38000000-3bfff000 (prefetchable)
    Memory window 1: 3c000000-3ffff000
    I/O window 0: 0000e800-0000e8ff
    I/O window 1: 00001000-000010ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
    16-bit legacy interface ports at 0001
    Kernel driver in use: yenta_cardbus
    Kernel modules: yenta_socket

    07:00.0 Network controller [0280]: RaLink RT2561/RT61 802.11g PCI [1814:0301]
    Subsystem: RaLink EW-7108PCg [1814:2561]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- SERR- Latency: 64, Cache Line Size: 128 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at 3c000000 (32-bit, non-prefetchable) [size=32K]
    Capabilities:
    Kernel driver in use: rt61pci
    Kernel modules: rt61pci


    ** Version:
    Linux version 2.6.24-1-686 (Debian 2.6.24-4) (waldi@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Mon Feb 11 14:37:45 UTC 2008

    ** Command line:
    root=/dev/hda1 resume=/dev/hda5 ro

    ** Not tainted


    -- System Information:
    Debian Release: lenny/sid
    APT prefers testing
    APT policy: (500, 'testing'), (500, 'stable')
    Architecture: i386 (i686)

    Kernel: Linux 2.6.24-1-686 (SMP w/1 CPU core)
    Locale: LANG=cs_CZ.UTF-8, LC_CTYPE=cs_CZ.UTF-8 (charmap=UTF-8)
    Shell: /bin/sh linked to /bin/bash

    Versions of packages linux-image-2.6.24-1-686 depends on:
    ii debconf [debconf-2.0] 1.5.20 Debian configuration management sy
    ii initramfs-tools [linux-initr 0.91e tools for generating an initramfs
    ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo

    Versions of packages linux-image-2.6.24-1-686 recommends:
    ii libc6-i686 2.7-6 GNU C Library: Shared libraries [i

    -- debconf information:
    shared/kernel-image/really-run-bootloader: true
    linux-image-2.6.24-1-686/preinst/overwriting-modules-2.6.24-1-686: true
    linux-image-2.6.24-1-686/postinst/bootloader-error-2.6.24-1-686:
    linux-image-2.6.24-1-686/postinst/create-kimage-link-2.6.24-1-686: true
    linux-image-2.6.24-1-686/postinst/old-system-map-link-2.6.24-1-686: true
    linux-image-2.6.24-1-686/prerm/would-invalidate-boot-loader-2.6.24-1-686: true
    linux-image-2.6.24-1-686/preinst/initrd-2.6.24-1-686:
    linux-image-2.6.24-1-686/preinst/failed-to-move-modules-2.6.24-1-686:
    linux-image-2.6.24-1-686/postinst/depmod-error-initrd-2.6.24-1-686: false
    linux-image-2.6.24-1-686/preinst/bootloader-initrd-2.6.24-1-686: true
    linux-image-2.6.24-1-686/postinst/old-initrd-link-2.6.24-1-686: true
    linux-image-2.6.24-1-686/preinst/lilo-has-ramdisk:
    linux-image-2.6.24-1-686/postinst/old-dir-initrd-link-2.6.24-1-686: true
    linux-image-2.6.24-1-686/preinst/abort-install-2.6.24-1-686:
    linux-image-2.6.24-1-686/prerm/removing-running-kernel-2.6.24-1-686: true
    linux-image-2.6.24-1-686/postinst/depmod-error-2.6.24-1-686: false
    linux-image-2.6.24-1-686/preinst/abort-overwrite-2.6.24-1-686:
    linux-image-2.6.24-1-686/preinst/elilo-initrd-2.6.24-1-686: true
    linux-image-2.6.24-1-686/postinst/bootloader-test-error-2.6.24-1-686:
    linux-image-2.6.24-1-686/postinst/kimage-is-a-directory:
    linux-image-2.6.24-1-686/preinst/lilo-initrd-2.6.24-1-686: true



    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

  2. Bug#475134: linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg

    On Wed, Apr 09, 2008 at 11:37:37AM +0200, Ond??ej Kunc wrote:
    >
    > I'am experiencing kernel panic when copying large files (>20M) over FTP,
    > using wi-fi card Edimax EW-7108Pcg. It's 100% repeatable. So I am ready
    > to test it a send traces of whatever is needed to fix it. But I don't
    > know, how to save the trace. I could make a screen photo, or copy trace
    > text by eyes. Ready to answer.


    okay please checkout newer kernel 2.6.25-rc8, see trunk apt lines
    -> http://wiki.debian.org/DebianKernel

    installs just fine in lenny/sid.



    --
    To UNSUBSCRIBE, email to debian-bugs-dist-REQUEST@lists.debian.org
    with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

  3. Bug#475134: marked as done (linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg)


    Your message dated Mon, 28 Apr 2008 12:08:45 +0000
    with message-id
    and subject line Bug#475134: fixed in linux-2.6 2.6.25-1
    has caused the Debian Bug report #475134,
    regarding linux-image-2.6.24-1-686: Kernel panic caused by network traffic on Edimax 7108Pcg
    to be marked as done.

    This means that you claim that the problem has been dealt with.
    If this is not the case it is now your responsibility to reopen the
    Bug report if necessary, and/or fix the problem forthwith.

    (NB: If you are a system administrator and have no idea what this
    message is talking about, this may indicate a serious mail system
    misconfiguration somewhere. Please contact owner@bugs.debian.org
    immediately.)


    --
    475134: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=475134
    Debian Bug Tracking System
    Contact owner@bugs.debian.org with problems


+ Reply to Thread