check RAID status - BSD

This is a discussion on check RAID status - BSD ; Hi, mpt0:vol0(mpt0:0:0): Settings ( Hot-Plug-Spares ) mpt0:vol0(mpt0:0:0): Using Spare Pool: 0 mpt0:vol0(mpt0:0:0): 2 Members: (mpt0:1:0:0): Primary Online (mpt0:1:1:0): Secondary Online mpt0:vol0(mpt0:0:0): RAID-1 - Optimal mpt0:vol0(mpt0:0:0): Status ( Enabled ) (mpt0:vol0:0): Physical (mpt0:0:0:0), Pass-thru (mpt0:1:0:0) (mpt0:vol0:0): Online (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru ...

+ Reply to Thread
Results 1 to 2 of 2

Thread: check RAID status

  1. check RAID status

    Hi,

    mpt0:vol0(mpt0:0:0): Settings ( Hot-Plug-Spares )
    mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    mpt0:vol0(mpt0:0:0): 2 Members:
    (mpt0:1:0:0): Primary Online
    (mpt0:1:1:0): Secondary Online
    mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    mpt0:vol0(mpt0:0:0): Status ( Enabled )
    (mpt0:vol0:0): Physical (mpt0:0:0:0), Pass-thru (mpt0:1:0:0)
    (mpt0:vol0:0): Online
    (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:1:0)
    (mpt0:vol0:1): Online
    da0 at mpt0 bus 0 target 0 lun 0
    da0: Fixed Direct Access SCSI-2 device
    da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit)
    da0: Command Queueing Enabled
    da0: 69878MB (143110144 512 byte sectors: 255H 63S/T 8908C)

    Is there a way to check the status of the RAID by command? I tried
    camcontrol but I'm not sure how exactly to use it. Something like for the
    ATA Version:

    ad4: 38154MB at ata2-master UDMA100
    ad6: 38154MB at ata3-master UDMA100
    ar0: 38154MB status: READY
    ar0: disk0 READY (master) using ad4 at ata2-master
    ar0: disk1 READY (mirror) using ad6 at ata3-master

    [root@mvt ~]# atacontrol status ar0
    ar0: ATA RAID1 status: READY
    subdisks:
    0 ad4 ONLINE
    1 ad6 ONLINE
    [root@mvt ~]#

    Thanks, Helmut

    --
    No Swen today, my love has gone away
    My mailbox stands for lorn, a symbol of the dawn


  2. Re: check RAID status

    Good question, please the same for scsi

    Am 17.07.2008, 20:08 Uhr, schrieb Helmut Schneider :

    > Hi,
    >
    > mpt0:vol0(mpt0:0:0): Settings ( Hot-Plug-Spares )
    > mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    > mpt0:vol0(mpt0:0:0): 2 Members:
    > (mpt0:1:0:0): Primary Online
    > (mpt0:1:1:0): Secondary Online
    > mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    > mpt0:vol0(mpt0:0:0): Status ( Enabled )
    > (mpt0:vol0:0): Physical (mpt0:0:0:0), Pass-thru (mpt0:1:0:0)
    > (mpt0:vol0:0): Online
    > (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:1:0)
    > (mpt0:vol0:1): Online
    > da0 at mpt0 bus 0 target 0 lun 0
    > da0: Fixed Direct Access SCSI-2 device
    > da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit)
    > da0: Command Queueing Enabled
    > da0: 69878MB (143110144 512 byte sectors: 255H 63S/T 8908C)
    >
    > Is there a way to check the status of the RAID by command? I tried
    > camcontrol but I'm not sure how exactly to use it. Something like for
    > the ATA Version:
    >
    > ad4: 38154MB at ata2-master UDMA100
    > ad6: 38154MB at ata3-master UDMA100
    > ar0: 38154MB status: READY
    > ar0: disk0 READY (master) using ad4 at ata2-master
    > ar0: disk1 READY (mirror) using ad6 at ata3-master
    >
    > [root@mvt ~]# atacontrol status ar0
    > ar0: ATA RAID1 status: READY
    > subdisks:
    > 0 ad4 ONLINE
    > 1 ad6 ONLINE
    > [root@mvt ~]#
    >
    > Thanks, Helmut
    >




    --
    Erstellt mit Operas revolutionärem E-Mail-Modul: http://www.opera.com/mail/

+ Reply to Thread